Cisco Switches :: Linksys SRW248G4 And Multiple Membership In VLANs?
Jun 26, 2012
I can't figure out how to configure a port membership with multiple VLANs. My setup:
- VLAN10
- VLAN20
- port settings tab: port24 in general mode
- ports to VLANs tab: untagged everywhere, when I set port 24 membership to VLAN10 I can't set port 24 membership in VLAN20 because when I do that port 24 membership in VLAN10 dissapears and vice versa
- but I can set port 24 membership to both VLANs in VLANs to port tab, but I think it doesn't work because:
- when I connect hosts to ports 23 (port 23 is a member of VLAN10 only) and 24 (member of VLAN10 and VLAN20)
there are not any connectivity between them
- but connectivity is working when I set the same PVID for both ports 23 and 24 in port setting tab, I can't set multiple PVID in here.
So, is it possible to configure port membership for multiple VLANs on this linksys. [URL]
View 1 Replies
ADVERTISEMENT
Jul 29, 2012
We are using Linksys SRW248G4 in our network as Layer 2 Device. We have configured QoS policy for Voice and Video Priority over Data. On Layer 3 we are using CISCO SGE 2000, on that we have also configured QoS Policy and that is working, if we are connecting two IP Phones on L3 Switch but when we are connecting IP Phones on L2 Linksys we are not getting Voice and Video quality over Data.P2P link is of 10MB.I am Putting Whole configuration of that switch in TEXT FILE. [code]
View 5 Replies
View Related
Jul 17, 2012
I was looking for configuring QOS for two VLANS i have created. these will be for voice traffic vlan 22 and video traffic vlan23. i also have three other vlans for pc's, wireless devices and our cnc machines. we have 5 switches that are all SG30028P's with a single switch doing the intervlan routing (operating at layer 3). all of the switches are trunked back to the main switch and ive been through the guide written on how to do this on a single switch which i dont think is layer 3.
View 5 Replies
View Related
Aug 20, 2012
I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
View 3 Replies
View Related
Jan 6, 2011
My customer requires the hostport on an access switch to be allocated to a specific Vlan based upon the AD Group that the user is a memeber of ? I am planning to setup NAC in a Real Gateway OOB deployment, using an ACS 5.2. I was initially thinking that the initial authentication server would be the ACS and then the AD, which using group mappings within the AD, I could then assign the user to a specific ACS group and then pass a Radius attribute back to the NAC manager for processing?
View 2 Replies
View Related
Aug 26, 2012
I have 2 SG300-10 switches, and I need two VLANs, one for internal network and one for WiFi APs.I need ports 1->4 on both switches to be part of 1st VLAN and ports 5->8 on 2nd VLAN; and port 10 uplink to 2nd switch.How I set up the VLANs and interface VLAN mode?
[code]...
View 1 Replies
View Related
Jun 22, 2011
I am having problems accomplishing these tasks with my new SG 200-18.
I have a LinkSys WRT54G2 connected to port 1. I would like ports 2-8 to be in one VLAN with access to the Internet and to be able to share their printers, hard drives, etc. with other computers on ports 2-8. I would like each of ports 9-16 to be on a separate VLAN with access only to the Internet and no other ports on the switch. I would like to be able to manage the switch from any of the ports 2-8.
After I create the VLAN 1009 (see screenshot below), port 9 can browse the Internet and cannot see the other ports on the switch which is correct. However, ports 2-8 can no longer access the switch at 192.168.1.20 in order to manage the switch.
View 10 Replies
View Related
Jun 21, 2011
I have SGE2010 switches and I want to implement Multiple VLANs. Im a newbie and starting to study VLANS's.
I want to implement 5 VLAN's on my test lab network and here as follows:
192.168.1.x default
192.168.2.x
192.168.3.x
192.168.20.x
192.168.100.x
The .1 is exclusively for my test-lab servers.
The .2 is general test-lab Win-XP workstations.
The .3 is general test-lab Win7 worstations
The .20 is general test-lab production worstations
The .100 is for test-lab IP PHONES.
View 4 Replies
View Related
Aug 19, 2012
I have to configure multiple vlans served with a unique DCHP server . As first step, I just will The DHCP server to serve 2 vlans. The following is the hardware and configuration that I implemented :
[code]...
But If I connect the DHCP server on a trunked switch port and adapt the DHCP server gateway 172.16.0.1 to 172.16.0.254, hosts receive ip address properly.I have to connect the DHCP server directly to the router. How can I do that, what is wrong in the configuration?
View 14 Replies
View Related
Aug 30, 2011
I have 8 apartments that have a single internet connection coming into the building, I then have a PoE Access Point in each of the 8x apartments.
What I would like to be able to do is to have each apartment within its own vlan, but to be able to use the internet via one of the non-PoE ports (port 9 say) but do not want residents in different flats to be able to see each others devices on the same network.
I have a Cisco SG 300-10MP which has 8x PoE ports and 2x Ethernet ports, one of which my Internet connection is plugged into (using WiMax).
View 2 Replies
View Related
Mar 28, 2012
We have a Cisco 887 router and a Cisco SG-200 switch.We'd like to setup trunking between these 2 devices for multiple VLANs on the switch to be made available on the router.
With previous routers, you could set the router up in the configuration 'router-on-a-stick' and VLANs worked like a charm but the 887 no longer support sub-interfaces.So how can you get trunking working between the 2 devices?
Is there a VTP configuration menu for the SG-200 which we can setup in order for it to talk 'VTP' with the 887 router??
View 1 Replies
View Related
Nov 17, 2011
We have been set the task of securing a small managed office system which is currently set up with a standard switch allowing each of the offices (containing different companies) to see each other, and in some cases, access each others documents across the network.
Obviously this is a far from adequate set up and our aim is to isolate each office using VLAN's but share a common internet connection provided by the managed offices. We have two Cisco SGE2000-G5 layer 3 switches but we are new to Cisco equipment and VLAN's so we are not quite sure on how to implement this. DHCP would need to be provided by a Router, there is no Server. We are open to suggestions on the Router as we have yet to purchase one.
View 10 Replies
View Related
Nov 11, 2012
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?
what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature
View 7 Replies
View Related
May 21, 2012
I have been fighting against this Lynksys cisco switch to be able to restore admin password, no success. Theorically, is just unplug and plug switch, press ESC and press option 3) Password Recovery Procedure. Then Enter and Enter and switch will boot normaly with admin/blank password, well, not work,.
*******************************************************************
*** Running SW Ver. 1.2.1b Date 31-Aug-2006 Time 13:47:21 ***
*******************************************************************
HW version is 00.03.00
Base Mac address is: 00:1e:e5:1c:fd:eb
[Code]......
View 1 Replies
View Related
Jun 2, 2013
I want to configure my SRW248G4 switch thru console port. Unfortunately in this switch there is no RJ45 console port input, I can only see cosole port that is look like RS232 input. I bought two standard cisco console cables that have one end with db9 and one with RJ45.
Now I have and idea to put one end of one cable (db9) to switch, and one end (db9) of second cable in my computer (COM input/output)
I need to connect two RJ45 together - this is not a problem, I know how to do this. Here is the question :I know how pinout in my computer look like but i can't find pinout of console port in my SRW248G4. There is many pictures in Internet, for many Cisco devices but this isn't working. Maybe in LINKSYS pinout look different ?
View 3 Replies
View Related
Dec 12, 2012
with TFTP upgrade SRW2xxG4_FW_1.2.3.0.ros and WEB interface after the restart, the switch will not start, display HyperTerminal link. You can also restore the switches do not?
View 1 Replies
View Related
Aug 13, 2011
I just received a new Cisco SG300-10 and am configuring it in Layer 3 mode. I am trying to setup multiple routed VLANs going back to a FiOS Actiontec router. My configuration is as follows.
Fios Router: 192.168.1.1
Assigning DHCP 192.168.1.2 through 100.
SG300-10 has VLan 1 ip 192.168.1.5 used for Mgmt.
VLAN2 is 10.0.2.1
VLAN3 is 10.0.3.1.
I have a static route set on the fios router for both subnets setup as follows.
Destination 10.0.3.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
Destination 10.0.2.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
I have a laptop connected to Gi8 on the Cisco (Vlan 3) and statically assigned 10.0.3.3, with a gateway of 10.0.3.1. DNS set to the fios router (192.168.1.1).
Everything pretty much works EXCEPT, I cannot get out to the internet from either vlan. Traffic routes between vlans/and the default subnet on the fios without issue.
When I ping out, DNS resolves, but will not go past the fios router. Am I missing a setting somewhere?
View 3 Replies
View Related
Sep 4, 2011
Any snmpset commands to modify port vlan membership on SG300-28 switches? I checked [URL] however this information is apparently only valid for catalysts.
The latest firmware is installed and the provided MIB files are used.
View 5 Replies
View Related
Aug 31, 2012
I have two Cisco SG300-20 switches. Both of them are configured in L3 mode. They have several VLAN's configured.
When I reboot my switches some VLAN membership settings are lost! I have already saved the settings over and over before rebooting, and even tried to save it to the backup memory and so on. Say for example I have changed port 9 to 14 from VLAN 101 to VLAN 105. I save the configuration, reboot the switch. And then the changes are lost. This is a big problem, because servers and my iSCSI network loose connectivity. They already have the latest firmware. This issue was there three firmwares before.
This issue pop-ups when I have a power loss, or I need to reboot/shutdown them manually. It may be off-topic but I also have the feeling that the performance of the switches goes down during uptime. A reboot solves the performance issue. I don't have a performance benchmark, but I can notice it on the performance transfer rate between clients and servers.
View 4 Replies
View Related
Oct 21, 2012
how i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
View 1 Replies
View Related
Sep 18, 2012
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies
View Related
Mar 9, 2010
Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies
View Related
Aug 20, 2012
I have 2 switch groups.
2 SGE2010's with VLAN's defined as 10,20 and 30
Vlan 10 is the management VLAN, and it uplinks to our border router.Vlan 20 is the workstation VLAN, and all workstations point to the switch as their default GW? Vlan 30 is the ip phone VLAN, and all phones use this as their gateway.
I would like to put a LAG between said switches, we have some servers on the ip phone switch that need to be accessed by the workstation clients, and the single 100mb link through the router is probably not going to be enough.As I understand it, because the switches have different networks on them, a simple lag will not work. I did create a lag, and assign ip addresses to each side, however in that mode, it doesn't appear I can block vlan 10 from transiting the LAG, and with out that block I will end up with a logical loop, and spanning-tree will block one of the uplinks, or the LAG itself.
View 10 Replies
View Related
Jan 26, 2013
How to configure DHCP server if i have 2 vlans. I know how to configure rest of the network, just i don't know server.I use packet tracer and i attached file with my network. PC1 is on VLAN1 and PC2 is on VLAN2.I want ip addresses in vlan1 to be from 192.168.1.2 and in vlan2 from 192.168.2.2. I would like to do it just like in the designed network, without router.
View 5 Replies
View Related
Apr 4, 2013
The network topology is like this. Router with DHCP_Server on it.
VLAN 10
VLAN 20
VLAN 30
My question is how to configure the router so that all devices on all 3 VLANS can obtain IP from the router. I've tried to enable proxy arp on all interfaces and create sub interfaces and trunk them to their appropriate vlans, but I can't specify the gateway on all trunked sub interfaces because I get a warning that addresses overlap. Then I tried to set access-group on all sub-interfaces and still doesn't work.
View 5 Replies
View Related
Jun 17, 2012
I'm trying to setup a VPN connection for the two PC's in the graphic below. I have the link between the two locations setup and secured, now I just working with the routing elements.what I need to add to the firewall config in order to get this to work? Here is what I have:
SITE A------access-list mpls_vpn_sitea extended permit ip host 172.168.199.1 host 172.168.199.2 access-list mpls_vpn_sitea extended permit ip TEST-LOCAL 255.255.255.0 TEST-REMOTE 255.255.255.0crypto map mpls_vpn 1 match address mpls_vpn_siteacrypto map mpls_vpn 1 set peer 172.168.199.2 crypto map mpls_vpn 1 set transform-set ESP-3DES-SHAcrypto map mpls_vpn interface MPLScrypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
SITE B------access-list mpls_vpn_siteb extended permit ip host 172.168.199.2 host 172.168.199.1 access-list mpls_vpn_siteb extended permit ip TEST-LOCAL 255.255.255.0 TEST-REMOTE 255.255.255.0crypto map mpls_vpn 1 match address mpls_vpn_sitebcrypto map mpls_vpn 1 set peer 172.168.199.1 crypto map mpls_vpn 1 set transform-set ESP-3DES-SHAcrypto map mpls_vpn interface MPLScrypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
do I need to specify a route between the two networks? What do I need to have for NAT statements?
View 10 Replies
View Related
Oct 23, 2012
I recently set up a Cisco 881 to cover a small business network. The router is currently set up and working as expected. We recently decided to move to VoIP phones and here is where I'm running into some issues.
First an overview: We run a network with a cable internet WAN connection, this connection is DHCP, however we have a static IP through our ISP. We also have a block of 30 additional IP addresses for one to one mapping as we need them. The new VoIP system is being run over T1 lines throughout the township (we are a municipal organization) and the VoIP system is being run to about 5 buildings in the township.
This brings me to the topic of VLANs. As the phone engineer explained it to me, there is a network set up over the T1 that allows the VoIP equipment to talk to one another and operates all of the VoIP phones on one network. The equipment that is being installed at our building connects to the network over the T1 and "talks" to the other equipment on the network. The engineer wants to create a VLAN and run it on ports fa1 and fa2, with the fa2 port being connected to the actual "MPLS" (their term) that connects to the T1 and into the cloud, and the fa1 port connected to the internal phone switch.
TLDR; The problem is this: When we attempt to set up the VLAN on ports fa1 and fa2, we have no connectivity with the other units in the external VoIP cloud. Pinging while directly connected to the "MPLS" yields successful pings, while pinging from the router with the "MPLS" connected to fa2 yields failures. I'm going to post the running config below, I feel like what we're doing should be working. I asked around about subinterfacing, but others seemed to think this was not necessary.
ROUTER CONFIG
Building configuration...
Current configuration : 4909 bytes
!
! No configuration change since last restart
version 15.1
[Code].....
View 10 Replies
View Related
Feb 20, 2008
I have two Cisco 1300's acting as bridges only. I have created an infrastructure ssid on VLAN 2 and assigned this to the radio. I am carrying multiple VLANs between the bridges (using subinterfaces on the fastethernet and radio ports).I have enabled WPA-PSK, but how do I check that this is being used between the bridges? Also - I have a switch connected at each end of the bridge. When I make VTP changes, the remote switch does not pick these up - is this because VTP goes over VLAN1 regardless of the Native VLAN (2 in my case)? Do I have to carry VLAN1 over the bridge to get VTP working, or is there an alternative solution?
View 7 Replies
View Related
Sep 27, 2012
I have a RV180W and a EnGenius EAP350 Access Point. The EnGenius supports multiple SSID's and VLAN tags them. If port 1 on the RV180W has VLAN 1 untagged and VLAN2 tagged, any connection to the EnGenius always gets an IP from the VLAN 1, even though they are connected to the SSID which is tagged with VLAN2.
View 3 Replies
View Related
May 22, 2011
I am trying to set up three vlans across two switches. The switches are Cisco SG200 and SG 300 series. There are 20 devices connected to the two switches including a router for Internet. Among these devices are five wireless access points all hardwired to the LAN. If I understand correctly the first thing I have to do is aggregate the two switches. I ran two cat5 cables to ports 1 and 2 of each switch. As I understand it all I need to do is to create SAG with the two ports on each switch. I think I need to use tagging but I don't really understand how to do this. Once I get the trunking set up correctly I want to create one vlan to which all devices will belong for Internet access. The other two would be for data and VoIP. Do I create vlans with the same name on both switches? When I assign the devices (by port) do I need to enable tagging? Which type of port setting should I use? I am assuming that by including the acess points in the vlans will mean that any wireless device connected to them will have acess to the Internet and the devices in the same vlan.
View 1 Replies
View Related
May 9, 2012
Switch: SG500 VLANS: 1 (default) xxx.xxx.0.0/24 network, 150 (device management vlan) xxx.xxx.150.0/24 network I am plugged into port 1. This is a trunk port with VLANs assigned as follows: VLAN 1 (Default) - UntaggedVLAN 150 (dev mgmt) - Tagged Device is plugged into port 2. This is an access port with the following VLAN assigned: VLAN 150 - Untagged Why is it I cannot communicate with the device on port 2?
View 1 Replies
View Related
Sep 13, 2012
I have a above said switch at my remote office (600KM) which is connected with L2 Point to Point leased line. Both the ends I have Cisco 3950 catalyst switches with Vlans configured at both the ends. Now, for obvious reasons I should remove the other end 3950 switch and replace with Cisco 2950 switch. The other end 3950 is having 4 Vlans configured on 4 ports. Now my requirement is, I should configure 3 Vlans (one for P2P, one for 10 Desktops and one for to bring traffic from other network).
View 1 Replies
View Related
Nov 17, 2011
The ASA device is going to be the gateway for multiple distinct inside IP subnets. We can have have a unique outside IP address to correspond to each inside IP subnet if needed, but we need some means for a VPN client or a site-to-site VPN to have acess to a pre-definied IP subnet (i.e. if customer A establishes a VPN connection, they have connectivity to IP subnet X; customer B establishes a VPN connection, they have connectivity to IP subnet Y, etc.).Currently, the two inside IP subnets are 10.10.0.0/16 and 10.20.0.0/16. We will be adding more.The problem we are facing is that we cannot reach the VLAN 201 from the ASA we believe this is because. I have setup two addresses on port 0/1 Vlan1, 10.10.20.2 and 10.20.20.1 as an alias. How can we make traffic for the 10.10.0.0/16 subnet untagged and traffic for the 10.20.0.0/16 subnet tagged for VLAN 201.
View 1 Replies
View Related
