Cisco Switching/Routing :: 2960 - Private Vlans Across Multiple Switches
Nov 11, 2012
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?
what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature
View 7 Replies
ADVERTISEMENT
Nov 12, 2012
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature?
View 1 Replies
View Related
Apr 30, 2012
I have a a hardware server running a VM hosting virtual servers which are all on different VLANs. My challenge now is to configure the switchport that the server is connected to, to see all the VLANs needed by this VM. The VM has an IP that is used for managing the server VMs which is on a different VLAN also.
My switch is a 2960 switch and it is presently trunked from the core switch.
View 3 Replies
View Related
May 7, 2013
I have a problem with DHCP. I have two 2960 connected with a port channel on ports 47 and 48 as trunk with native vlan 10. I only have this one vlan. In port 1 of sw 1, I have a C800 as DHCP server.
I have an AP autonomous with single ssid on vlan 10. When I connect the AP to sw1, I receive dhcp with no problems.When I connect the AP to sw 2, I’m not getting IP by DHCP.I have DHCP snooping working on vlan 10 on both devices.
The ports where I connect the AP are access ports on vlan 10 config as trusted.The trunk ports are also configured as trusted.The port 1 of ws 1 that goes to the C800 is also configured as trusted.
figure out why I’m not getting IP by DHCP when I connect the AP to the SW 2.The only I notice is that when I connect the AP to sw 2, I get on SW 1 the message of packet drop by option 82, but even after configuring ip dhcp snooping information option allow-untrusted on both switches, the problem persists.
View 5 Replies
View Related
Sep 5, 2012
Is this supported on a 3750X ?? A router has two VRFs and its lan interface is a trunk with 2 VLAN IDs, let say VLAN 10 and VLAN 20. The ip address subnet of these two vlans is the same (therefore , they are in different VRFs)
fa0/1
VLAN 10 = 10.15.4.9 (VRF A)
VLAN 20 = 10.15.4.10 (VRF B)
This router is connected on a 3750X switch. There is a firewall connected to this switch also, which is default gateway for several VLANs including VLAN 10 (10.15.4.1)
The goal is that VRF B ip can talk to 10.15.4.1 and VRF A can talk to 10.15.4.1 but VRF B can't talk to VRF A (10.15.4.9 <-> 10.15.4.10)
FW |--- TRUNK VLANs 1,2,3,4,10 ---------| SWITCH |----- TRUNK VLAN 10,20 -----| ROUTER (vlan 10 = VRF A, vlan 20 = VRF B)
I think this is not supported on the C3750, as my promiscuous port is located on a trunk.
View 1 Replies
View Related
Aug 28, 2012
We have a requirement for private VLANS for DMZ hosting within one of our datacentres. I just want to query how private VLANs would work in our environment.We have physical servers connected to fex ports (2 fex per rack for each 5k) of a 5548UP switch, virtual servers using the nexus 1000v (vmware hosts connected to fex ports) Out firewalls and load balancers are connected to an upstream pair of nexus 7ks using vPCs.My question is this, ordinarily the firewall would be in a promiscuous port but as these reside on a physically separate switch will the normal vPC trunk still be sufficient or would the "switchport mode private-vlan trunk promiscuous" be required on the vPC up to the northbound 7k.As these connections are already in production I do not want to affect the existing traffic that doesn’t use private VLANs.
View 3 Replies
View Related
Aug 13, 2012
regarding PVLANs and the Nexus, my understanding is that we cannot configure Private VLANs on a FEX trunk port with a NX-OS release older than 5.1(3)N2(1) for the Nexus5548... Is there any known workaround for this limitation (appart from performing a SW upgrade)?
View 2 Replies
View Related
Mar 9, 2010
Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies
View Related
Nov 29, 2011
We currently have a HP blade platform which has two Cisco CBS30X0 switches built into it running Version 12.2(55)SE. These are connected to two Cisco C2960 aggregation switches running Version 12.2(44)SE6. According to this article I need to upgrade these to 12.2(25)FX: url...
1.)This will according to that article only allow me to create edge ports on them, is this a hardware limitation or am I just not finding what firmware I need to upgrade them to, in order to allow the creation of community VLANs? We have these aggregation switches conncted directly to multiple types of firewalls which take care of each of our clients networks including internet access etc. We are wasting many VLANs and IP addresses with our current setup so I am hoping to move over to using private VLANs. The setup of the private VLANs looks simple enough.
2.)When the private VLAN's try to communicate, all info will be sent directly to the layer 3 device I gather, which will not need to know anything about the private VLANs?
View 12 Replies
View Related
Nov 3, 2012
Need to confirm if WS-C3750-48TS-S supports Private vlans and IPV6?
Also need to know which stack cable like part number i can use for stacking them .
View 3 Replies
View Related
Mar 13, 2013
I have 2960 cisco switch. I want to configure private vlan. But it is not getting configured in cisco 2960. Is there any other way to configure that in switch.
View 1 Replies
View Related
Mar 25, 2013
How to setup 3 SG300-52 (in L2 mode) as per this diagram:Port 1 on all switches should be able to talk to each other and access the blob at the right.The ports 25 on the other hand should only be able to talk among themselves in their own private vlan. They are to carry sensitive traffic. So I created 3 vlans, vlan 78 for ports gi1, gi51 and vlan 10 for port25,49,50 and a dummy vlan: 666 with the intent of segratating vlan 10 from vlan 78. My attempts so far have failed. ports gi49-50 are configured as trunk ports and gi1,gi51 as access ports as the following cli output (excerpts of the startup config):
vlan database
vlan 10,78,666
exit
interface vlan 1
ip address 172.16.10.11 255.255.255.0
[code]....
Ports gi1 can talk to each other and access the blob but ports 25 refuse to talk to each other. But as soon as I remove the access links to the blob they can! Obviously, at that point port gi1 lose access.Is such a topology feasable or even advisable?
View 7 Replies
View Related
Feb 7, 2012
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies
View Related
Feb 8, 2012
I have two switches, a 2960 (sw01) and a 2948 (sw02). The sw01 is trunking via dot1q on Gi0/24 to sw02 on 2/48. Why are VLANs 2-4 not active on sw02?
sw01#sh int Gi0/24 trunk
Port Mode Encapsulation Status Native vlan
Gi0/24 auto 802.1q trunking 1
Port Vlans allowed on trunk
Gi0/24 1-4094
[code].....
View 5 Replies
View Related
Sep 26, 2012
How can i add two data vlans on cisco 2960 on one interfase? i have 3 mac adresses on one interfase: one PC, one ipphone and one XP virtual machine(VM). PC and VM are in one data vlan and phone is in voice vlan. i need to place the VM in another data vlan is it possible? if so could you give me a link or place information here.
View 2 Replies
View Related
Oct 23, 2012
I recently set up a Cisco 881 to cover a small business network. The router is currently set up and working as expected. We recently decided to move to VoIP phones and here is where I'm running into some issues.
First an overview: We run a network with a cable internet WAN connection, this connection is DHCP, however we have a static IP through our ISP. We also have a block of 30 additional IP addresses for one to one mapping as we need them. The new VoIP system is being run over T1 lines throughout the township (we are a municipal organization) and the VoIP system is being run to about 5 buildings in the township.
This brings me to the topic of VLANs. As the phone engineer explained it to me, there is a network set up over the T1 that allows the VoIP equipment to talk to one another and operates all of the VoIP phones on one network. The equipment that is being installed at our building connects to the network over the T1 and "talks" to the other equipment on the network. The engineer wants to create a VLAN and run it on ports fa1 and fa2, with the fa2 port being connected to the actual "MPLS" (their term) that connects to the T1 and into the cloud, and the fa1 port connected to the internal phone switch.
TLDR; The problem is this: When we attempt to set up the VLAN on ports fa1 and fa2, we have no connectivity with the other units in the external VoIP cloud. Pinging while directly connected to the "MPLS" yields successful pings, while pinging from the router with the "MPLS" connected to fa2 yields failures. I'm going to post the running config below, I feel like what we're doing should be working. I asked around about subinterfacing, but others seemed to think this was not necessary.
ROUTER CONFIG
Building configuration...
Current configuration : 4909 bytes
!
! No configuration change since last restart
version 15.1
[Code].....
View 10 Replies
View Related
Dec 19, 2012
I have two Catalyst 2960 Series (48 port) switches with the newest Cisco IOS installed. There is also a Cisco 2600 Series Router which I can't manage because it's ISP managed.
Now the problem is as follows. I'd like to create two VLANs, one in the IP range 192.168.0.xxx and the other in the 192.168.1.xxx. Now the router has a gateway IP address 192.168.1.1 .
Would it be possible to somehow connect these two VLANs with the router so that these 2 VLANs can't see each other but they can ofcourse both contact the router and exit on the internet?
View 3 Replies
View Related
Nov 22, 2011
On a low-end switch like a 2960 the maximum VLANs is 255, as shown in the output of VTP status:
Maximum VLANs supported locally : 255
Number of existing VLANs : 245
When the VTP mode is changed to transparent, VLANs from the extended range can be added without increasing the number of existing VLANs - e.g. if I create VLANs 3000 - 4000 the number of existing VLANs is still listed as 245.
If MST is used to cut down on the number of spanning-tree instances - and assuming propagation of VLAN configuration via VTP is not required - is there any downside to using transparent-mode VTP to increase the number of available VLANs? It does feel like I'm cheating the maximum listed in the datasheet.
View 4 Replies
View Related
Mar 7, 2012
I've just started a new job after a couple of years not touching cisco gear and been pitched in... My new employer has a network that's Juniper based. We've inherited a load of Cisco switches as part of the deal for hosting matches during the Rugby world cup (plus a load of Aruba wireless gear that promises to be my very own special millstone, but that's bye the bye.)
My task is to hang these catalyst 2960's onto our existing infrastructure via fibre connections.
On the Juniper switch, there are four vlans being pushed to the port the cisco's hooked into: Code...
View 7 Replies
View Related
May 9, 2012
Switch: SG500 VLANS: 1 (default) xxx.xxx.0.0/24 network, 150 (device management vlan) xxx.xxx.150.0/24 network I am plugged into port 1. This is a trunk port with VLANs assigned as follows: VLAN 1 (Default) - UntaggedVLAN 150 (dev mgmt) - Tagged Device is plugged into port 2. This is an access port with the following VLAN assigned: VLAN 150 - Untagged Why is it I cannot communicate with the device on port 2?
View 1 Replies
View Related
Sep 13, 2012
I have a above said switch at my remote office (600KM) which is connected with L2 Point to Point leased line. Both the ends I have Cisco 3950 catalyst switches with Vlans configured at both the ends. Now, for obvious reasons I should remove the other end 3950 switch and replace with Cisco 2950 switch. The other end 3950 is having 4 Vlans configured on 4 ports. Now my requirement is, I should configure 3 Vlans (one for P2P, one for 10 Desktops and one for to bring traffic from other network).
View 1 Replies
View Related
Mar 13, 2012
I can not get dhcp to work.I can ping from the switch to both vlans...
here is my config for the router.....
Router is a 1760
Current configuration : 1379 bytes
!
version 12.4
service timestamps debug datetime msec
[Code]....
View 1 Replies
View Related
Jul 17, 2012
I was looking for configuring QOS for two VLANS i have created. these will be for voice traffic vlan 22 and video traffic vlan23. i also have three other vlans for pc's, wireless devices and our cnc machines. we have 5 switches that are all SG30028P's with a single switch doing the intervlan routing (operating at layer 3). all of the switches are trunked back to the main switch and ive been through the guide written on how to do this on a single switch which i dont think is layer 3.
View 5 Replies
View Related
Aug 20, 2012
I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
View 3 Replies
View Related
Jun 18, 2012
I was assigned a task to configure an SG300-28P to have 3 different vlans.Now on VLAN1 their will be only one device configured with static IP 192.168.0.230,On the other 2 VLANS there will be a separate router connected on each one of them and will also act as a DHCP server.
View 4 Replies
View Related
Jan 23, 2011
I'm going to move offices into a shared situation with 3 companies. Each company will want its own private network so there's no snooping between companies. I am planning on using VOIP for the phone system (Nextiva cloud based). Is it possible to set up the system so that each company has access to the VOIP system but yet remains sequestered in the their own network for everything else. I was hoping to do this with one data port at each workstation using Cisco SPA-303 phones. The way I understand this, is that the phone plugs in to the data port and you daisy chain the workstation off from each phone. Is this possible to do this while having the system I described? Another wrinkle is that I'd also like all the networks to be access shared printers.
View 7 Replies
View Related
Apr 11, 2012
I would like to configure a 3750 switch port to be able to use two vlans. I know you can do this with a voice and data vlan, but what about two data vlans ? Say I have two devices, one on a 10 subnet and the other on a 172 subnet, but i only have one wall jack for both devices to plug into. So I use a mini switch to connect both devices and connect the switch to the wall jack; and of course this all leads back to one switch port. When I go to enter the switchport access vlan 172 cmd, how would I also make it so the device on the 10 subnet could route out ?
View 9 Replies
View Related
Feb 17, 2013
We need to give differentiated internet access to three VLANs. Each one of this VLANs is used for totally different purposes, so traffic between the VLANs is not allowed. Each VLAN has its own internet access provided for the data center using one fast ethernet connection.
We're thinking about using cisco 2911 for Internet access, VPN and firewall. I suppose that best option for VLANs is using Catalyst 2960S or a swithing module for the 2911, but these two options are too expensive for us. We're thinking about using swtiches from the SB series (maybe a SG-200).
We're totaly newbies to VLANs so we have many doubts. This are our questions:
1) The 2911 has three on board ethernet interfaces; we have three VLANs and three internet connections, so we need to use HWICs to get three more ethernet ports. That's right?
2) We need three HWICs or there is some kind of HWIC with more that one ethernet interface?
3) The routing solution is to assign static routes in the 2911 for each interface connected to a VLAN through a 2911's interface connected to internet?
4) Simply connecting three different router interfaces with three different switch ports, each one of them assigned to one of the three different VLAN, are we going to get internet access for all devices in those VLANs? or do we need to configure something else like trunking, VSIs...?
5) Can we achieve our goals using the SG-200 switch?
6) We have the chance to use older routers, is this possible? We're specially interested in knowing if a 1841 or a 2801 router could be used for this setup.
7) This is not a production environment so we can use refurbished equipment.
View 4 Replies
View Related
Aug 27, 2007
We have a customer that is relocating thier headquarters. They have a temporary requirement to bridge multiple vlans or a router T3 link to the new location as they cannot change the IP subnets. Setup is 3560 switch connecting to a 3845 then T3 to remote 3845 and 3560. I need to bridge multiple VLANs. I have seen a good example on how to do it over sonet but I don't see how to translate that to an HDLC or Frame Relay encapsulation for the T3 Link.
View 5 Replies
View Related
Mar 11, 2013
Using Cisco 2960 series switches (Have 8 . 2 stacks of 4) to replace 6 old switches. 4 old switches had IP ranges of 192.168.6.*** and all new switches have 10.1.*.* addresses. Core switch has 10.1. as well as 192.168 ip addresses but i need to configure one vlan (5?) to route to 192.168 address. PC's on 10. address taking a long time to access 192 range.
View 2 Replies
View Related
Feb 12, 2012
I have a Cisco SG200 26 Port Switch, 2 Cisco WAP4410N Access points, and a VLAN aware Router. I have created 4 VLAN's. For the sake of this conversation lets call them.
98 - Intel Vpro
99 - Management
100 - General
101 - Guest
The Access points are capable of doing V LAN tagging so I plan on having them tag a guest network as V LAN 101. That can get sent to the V LAN aware router and out. No problem. I have some devices, or management pages that I don't want accessible from the general network. (Intel V pro KVM, Remote Management Cards, AP Config Menus, Switch config menu...) . I need to be able to take a V LAN unaware device, plug it into port 1, and have it communicate with V LAN 98, 99 and 100.
View 1 Replies
View Related
May 21, 2012
We're going to be switching some of our gear from Foundry to Cisco, and were looking at the WS-C2960S-48TS-L. We currently have 3 different VLAN's, and I wanted to have 1 uplink back to our firewall (ASA 5550) and then let the firewall do the routing between the subnets. I realize that 1 link will carry the traffic twice then, but is that possibly with those switches to have all three vlans assigned to one port and then just let the firewall do the routing between the vlans or would I need to have 3 uplink ports back to the 5550?
View 1 Replies
View Related
Apr 7, 2012
My problem is that I have a Cisco 300 series small business switch with multiple VLANS each one with an IP address and two or three ports assigned to each VLAN. I have an E3200 wireless router that I want to use to use to share internet on the switch. All of the VLANs are reachable from the other VLANs and I've put a static route on the E3200 so that I can reach the VLANs from a machine connected only to the router. But I can't reach machines on the otherside of the router or get to the internet from the switch.
View 3 Replies
View Related
