Cisco Switching/Routing :: Internet Sharing Multiple VLANS 300 Series Small Business Switch
Apr 7, 2012
My problem is that I have a Cisco 300 series small business switch with multiple VLANS each one with an IP address and two or three ports assigned to each VLAN. I have an E3200 wireless router that I want to use to use to share internet on the switch. All of the VLANs are reachable from the other VLANs and I've put a static route on the E3200 so that I can reach the VLANs from a machine connected only to the router. But I can't reach machines on the otherside of the router or get to the internet from the switch.
View 3 Replies
ADVERTISEMENT
Nov 2, 2010
i have major problem with two new Small Business 300 Series switches.Everytime i try to save the running config i get a GUI error message: "Another copy process is active, please try again later."It's also not possible to re-flash the firmware because the GUI stops responding.I have also tried to do this via console access and this produces a "the copy utility is occupied by another user" error message.-> so this is not a browser based problem.My first thought was that the switch (SG 300-28) is faulty so i unpacked the next new one (SF 300)and got the same error messages!Then i had a 2 hour webex support session with the Cisco Small Business Support and they did not found a reason for this behavior.Both switches are working normally, you can configure them, but after a reboot they are back to factory default again There is no possibilty for copy running config to startup config and it's also not possible to flash the firmware.(Web GUI & Console). tell me if this is a fundamental problem of the 300 Series?
View 6 Replies
View Related
Mar 6, 2012
[code] Basically, we used to use Outlook for our customer management, but after I tried to design a custom form for customers that suited our needs better than Outlook's default form (i.e. we don't need state, country, region, etc. for each customer, and we'd prefer to have spots for Roof, Shingle, Shingle color, etc. in their place), we ended up turning OneNote into our new Customer Management System.Our problem is sharing files, and the security or lack thereof that goes along with it.We used to save all the files to a single computer, and use Windows 7 Home group to access them. That worked okay, but often we couldn't see the file-holding computer, and would have to disconnect/reconnect to the internet.
We recently bought a NAS HD, which actually works a lot better than I expected. Unfortunately, we've learned recently that new employees are not always the most trustworthy. So this is what we are trying to do:We want to set up some type of way for us to save, store, and access files, which allows us to keep track of who has done what (access, save, copy, delete, print, etc.), preferably one where we can set up alerts if certain things happen (i.e. someone copies and pastes the entire thing, or attempts to delete). We've run into the problem where, yes, we want people to be able to copy and paste certain documents, yes we want people to be able to print, but no we don't want someone to be able to print out our entire customer lists, current project lists, etc.This NAS HD (MyBook Live 2TB by Western Digital) could quite possibly have the most ridiculous set up I've ever encountered. I can set up accounts and passwords, but they are completely irrelevant because from "Computer" you can just select the z:/ drive and it will still take you to our files. We just brought on a couple new people, and its like, everyone tells them to come to me in regards to the computers, and I can't even hook them up to the internet because it would give them access to our network, which in turn gives them access to our z:/ drive, which contains every file our company has.
View 7 Replies
View Related
Mar 9, 2010
Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies
View Related
Aug 26, 2012
I've got an RV180W for my office, and so far it has been great. I have two users that use a certain application that crashes all the time. For some reason, they don't crash when put into the DMZ. Is there any way i can put both of them in the DMZ? I can only figure out how to have one host in the DMZ at a time.
View 1 Replies
View Related
May 1, 2013
I need to extract the serial numbers of SFPs which are plugged in a SG-200-18.For information, SG-200 doesn't have a CLI ... only a Web GUI.I just find this information : [URL]
View 2 Replies
View Related
Feb 21, 2012
We recently deployed SG300-28 to replace an old 3Com switch.The setup: RVS400 router and all workstations and server are plugged into the SG300 switch.The problem: Windows 7 workstations are unable to obtain IP addresses from the server which is also plugged into the switch.If however, we plug in the worstations into the 4 port switch on the back of the RVS4000 (the router), they get IPs from the server no problem. This worked just fine with the old 3Com switch.
View 15 Replies
View Related
Feb 19, 2011
I was looking at the Cisco SRW2008 since for one, I like Cisco and two, it has WebView which should make it easy for an idiot like me to manage. Here are some of the features I am looking for.
VLAN support
ACLs
NIC Teaming
Gigabit - Up to 16 ports
Easy to Manage
PoE - Not necessary
No more than $500
There will be 2-3 physical servers connected to it, and many VMs in use.
View 19 Replies
View Related
Oct 6, 2011
i have a customer that will use this switch model.I was wondering if there is any recommendation from like an AS-BU for the most appropriate software version and what would be ?
View 4 Replies
View Related
Apr 27, 2013
They have a locked Cisco Router which is from the ISP and its confed on a fa 0/0 interface to share Internet access on the network. The ip on that interface is 195.198.11.217 255.255.255.252 and i tried it with a PC (set my personal ip to .218 and entered their dns info (195.67.199.27) and it is working. The question is now. My friend found a 3550 laying around and since the ISP wont let them conf their router he wants to use the 3550 to create 2 vlans with internet access and without access to eachother. Vlan 10 for the desktops and Vlan 20 for the wireless (Moving on to some netgear wireless switches) How would you configure the 3550 for this to work?
View 23 Replies
View Related
Apr 5, 2013
i am trying to set up a cisco 2950 with a vlan to seperate all of the pos machines on the network (4 of them) from all other machnes in the building (3 hard wired and wi-fi). i was going to use vlan 1 as a trunk to allow internet access to go from fa0/1 to both vlans (vlan 10 and vlan 20). i have read things about the acl having an explicit deny at the end, so i'm thinking that is my problem. i am testing it at my house before deploying it to the network. i have 1 laptop setup with an ip of 192.168.0.50, and the other is .60. my router is 192.168.0.1. i have the ethernet from the router plugged into fa0/1, the 1st laptop on fa0/2 and the other at fa0/3. before i set the vlans up, i checked the communication by just plugging them in and trying to ping, they could both ping each other, the router and 8.8.8.8. when i finished setting up the test vlans, they could not ping each other(what i wanted) and laptop 1 can ping the router, and 8.8.8.8. laptop 2 cannot ping anything.
the only thing i did was create vlan 10 and 20, set port fa0/2 to vlan 10 and no sh, fa03 to vlan 20 and no sh, fa0/1 to vlan 1 and no sh. then i did switchport mode trunk on fa0/1, and switchport native vlan 1. this seems to be how i was supposed to do it, but it's been a while since i have worked with switches. i'm sure it's simple, but after searching the internet and poring over my cisco books for 5 hours, it is turning out not to be the case. here are some details:
greenhouse#sh int fa0/1 switchport
Name: Fa0/1
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
[code]...
View 10 Replies
View Related
Sep 1, 2011
The SMART Designs state that both the ESW500 and 300-series switches should not be used for deployments of over 100 IP phones.But now that both the UC560 can go up to 138 (128 IP phones) and the BE3000 can go up to 300 users is this design restriction still valid or is the Catalyst 2960 and above the only options?
The QPT is still showing both the 300- and ESW500 switches as options for all versions of the UC560, and the 300- and 2960 switches are shown as valid options in the LAN for the BE3000.
View 5 Replies
View Related
Feb 17, 2013
We need to give differentiated internet access to three VLANs. Each one of this VLANs is used for totally different purposes, so traffic between the VLANs is not allowed. Each VLAN has its own internet access provided for the data center using one fast ethernet connection.
We're thinking about using cisco 2911 for Internet access, VPN and firewall. I suppose that best option for VLANs is using Catalyst 2960S or a swithing module for the 2911, but these two options are too expensive for us. We're thinking about using swtiches from the SB series (maybe a SG-200).
We're totaly newbies to VLANs so we have many doubts. This are our questions:
1) The 2911 has three on board ethernet interfaces; we have three VLANs and three internet connections, so we need to use HWICs to get three more ethernet ports. That's right?
2) We need three HWICs or there is some kind of HWIC with more that one ethernet interface?
3) The routing solution is to assign static routes in the 2911 for each interface connected to a VLAN through a 2911's interface connected to internet?
4) Simply connecting three different router interfaces with three different switch ports, each one of them assigned to one of the three different VLAN, are we going to get internet access for all devices in those VLANs? or do we need to configure something else like trunking, VSIs...?
5) Can we achieve our goals using the SG-200 switch?
6) We have the chance to use older routers, is this possible? We're specially interested in knowing if a 1841 or a 2801 router could be used for this setup.
7) This is not a production environment so we can use refurbished equipment.
View 4 Replies
View Related
Oct 22, 2011
I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Any simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic between the two vlans without an external router?
-VLAN1 10.10.10.0
-VLAN2 10.10.20.0
I've tried to do this through the GUI and can't seem to make it work. I'm missing something in the GUI.
View 6 Replies
View Related
Feb 22, 2012
I have a small cisco switch cluster (seven different 2924, 3524cisco switches) with 3550 as a cluster control which does all the inter vlan routing that works fine.
This cluster is in semi production PBX interop testing lab. This is a closed network without internet access and not connected to our corporate network.However now I have to add this capability so some equipment in the lab can get Microsoft updates over the internet.
I've created a port on a 3550 (fa0/19) and connected it to another network that has internet access. It picked an ip address and when I'm logged in to the 3550 I can ping hosts on the outside network. However I can't ping any hosts on that network from any hosts that are connected to my vlans.I've tried a few different things, but still can't make it to work.
Here is a short version of my 3550 configuration:
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log datetime
no service password-encryption
[code]....
View 13 Replies
View Related
Oct 23, 2012
I recently set up a Cisco 881 to cover a small business network. The router is currently set up and working as expected. We recently decided to move to VoIP phones and here is where I'm running into some issues.
First an overview: We run a network with a cable internet WAN connection, this connection is DHCP, however we have a static IP through our ISP. We also have a block of 30 additional IP addresses for one to one mapping as we need them. The new VoIP system is being run over T1 lines throughout the township (we are a municipal organization) and the VoIP system is being run to about 5 buildings in the township.
This brings me to the topic of VLANs. As the phone engineer explained it to me, there is a network set up over the T1 that allows the VoIP equipment to talk to one another and operates all of the VoIP phones on one network. The equipment that is being installed at our building connects to the network over the T1 and "talks" to the other equipment on the network. The engineer wants to create a VLAN and run it on ports fa1 and fa2, with the fa2 port being connected to the actual "MPLS" (their term) that connects to the T1 and into the cloud, and the fa1 port connected to the internal phone switch.
TLDR; The problem is this: When we attempt to set up the VLAN on ports fa1 and fa2, we have no connectivity with the other units in the external VoIP cloud. Pinging while directly connected to the "MPLS" yields successful pings, while pinging from the router with the "MPLS" connected to fa2 yields failures. I'm going to post the running config below, I feel like what we're doing should be working. I asked around about subinterfacing, but others seemed to think this was not necessary.
ROUTER CONFIG
Building configuration...
Current configuration : 4909 bytes
!
! No configuration change since last restart
version 15.1
[Code].....
View 10 Replies
View Related
May 9, 2012
Switch: SG500 VLANS: 1 (default) xxx.xxx.0.0/24 network, 150 (device management vlan) xxx.xxx.150.0/24 network I am plugged into port 1. This is a trunk port with VLANs assigned as follows: VLAN 1 (Default) - UntaggedVLAN 150 (dev mgmt) - Tagged Device is plugged into port 2. This is an access port with the following VLAN assigned: VLAN 150 - Untagged Why is it I cannot communicate with the device on port 2?
View 1 Replies
View Related
Sep 13, 2012
I have a above said switch at my remote office (600KM) which is connected with L2 Point to Point leased line. Both the ends I have Cisco 3950 catalyst switches with Vlans configured at both the ends. Now, for obvious reasons I should remove the other end 3950 switch and replace with Cisco 2950 switch. The other end 3950 is having 4 Vlans configured on 4 ports. Now my requirement is, I should configure 3 Vlans (one for P2P, one for 10 Desktops and one for to bring traffic from other network).
View 1 Replies
View Related
Mar 13, 2012
I can not get dhcp to work.I can ping from the switch to both vlans...
here is my config for the router.....
Router is a 1760
Current configuration : 1379 bytes
!
version 12.4
service timestamps debug datetime msec
[Code]....
View 1 Replies
View Related
Apr 30, 2012
I have a a hardware server running a VM hosting virtual servers which are all on different VLANs. My challenge now is to configure the switchport that the server is connected to, to see all the VLANs needed by this VM. The VM has an IP that is used for managing the server VMs which is on a different VLAN also.
My switch is a 2960 switch and it is presently trunked from the core switch.
View 3 Replies
View Related
Jun 18, 2012
I was assigned a task to configure an SG300-28P to have 3 different vlans.Now on VLAN1 their will be only one device configured with static IP 192.168.0.230,On the other 2 VLANS there will be a separate router connected on each one of them and will also act as a DHCP server.
View 4 Replies
View Related
Nov 11, 2012
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?
what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature
View 7 Replies
View Related
Apr 11, 2012
I would like to configure a 3750 switch port to be able to use two vlans. I know you can do this with a voice and data vlan, but what about two data vlans ? Say I have two devices, one on a 10 subnet and the other on a 172 subnet, but i only have one wall jack for both devices to plug into. So I use a mini switch to connect both devices and connect the switch to the wall jack; and of course this all leads back to one switch port. When I go to enter the switchport access vlan 172 cmd, how would I also make it so the device on the 10 subnet could route out ?
View 9 Replies
View Related
Aug 27, 2007
We have a customer that is relocating thier headquarters. They have a temporary requirement to bridge multiple vlans or a router T3 link to the new location as they cannot change the IP subnets. Setup is 3560 switch connecting to a 3845 then T3 to remote 3845 and 3560. I need to bridge multiple VLANs. I have seen a good example on how to do it over sonet but I don't see how to translate that to an HDLC or Frame Relay encapsulation for the T3 Link.
View 5 Replies
View Related
Feb 12, 2012
I have a Cisco SG200 26 Port Switch, 2 Cisco WAP4410N Access points, and a VLAN aware Router. I have created 4 VLAN's. For the sake of this conversation lets call them.
98 - Intel Vpro
99 - Management
100 - General
101 - Guest
The Access points are capable of doing V LAN tagging so I plan on having them tag a guest network as V LAN 101. That can get sent to the V LAN aware router and out. No problem. I have some devices, or management pages that I don't want accessible from the general network. (Intel V pro KVM, Remote Management Cards, AP Config Menus, Switch config menu...) . I need to be able to take a V LAN unaware device, plug it into port 1, and have it communicate with V LAN 98, 99 and 100.
View 1 Replies
View Related
Nov 16, 2012
I'm involved in setting up a new office for a business that's just starting out. I have some computer experience but not a whole lot in networking and security. We just have 3 people that will be working in the office and we need a way to store/backup/share files on the network as well as a way to access them remotely if need be. Our internet service is going to be providing us with a static IP. I was thinking that we could use an NAS with RAID 1 attached to the router, which is in turn connected to the cable modem, but I'm not sure if this is secure. Do we need some type of hardware firewall in between the cable modem and the router to protect us from the outside?
View 2 Replies
View Related
Dec 29, 2011
I'm currently using LMS 3.2 to monitor my network. We've recently purchsed a few of the Cisco Small Business Switches, the SF 300-24 model to be exact. They're considered 'managed switches' (tho thier CLI is terrible) and I would like to monitor them in CWLMS. My problem is that once I add it to CS, it doesn't resolve to anything, just sits there as a blue box with a question mark. I'm assuming this means that these devices are not (currently) supported by LMS 3.2 - do you know if that will change, or how I can go about managing this device with LMS 3.2?
View 2 Replies
View Related
Sep 30, 2011
I just took a position and never had to work with networks that much before. Our lan is very slow and trying to figure out why. We have verizon business class 3 t1 lines dedicated 4 M. When I do a speed test we get about 4.05 average and 4.23 down. We have 11 computers on the network connected to a Dell power connect 2716. We have Two network printers and that is it. We are having problems with it being very slow when connecting to a share on the server or using RDP.
View 4 Replies
View Related
Jun 3, 2011
I work for a small business of five computers. We have a wireless network for internet traffic, and a wired network for file sharing. The wireless network works great for using the internet, but we are having trouble with the wired network.The issue is being able to communicate with all of the computers on the wired network. The ability to speak with all of the computers on the network is hit or miss. Generally, computer A can speak with computer B, C, and D, but D can only speak with A.
View 4 Replies
View Related
Feb 13, 2012
He currently has 1 server, and 11 workstations, he also has a network switch that we will be replacing.We have picked out a Dell server, running Windows Server 2008 R2 that will be used as the main file server, as well as the domain controller. Where I seem to be confused is on setting up the networking component, particularly how the machines will get IP addresses. As mentioned, I will be purchasing a new Ethernet switch, in order to get the fastest LAN speed possible; I have selected the Dell PowerConnect 2816, which is a 10/100/1000Mbs switch. My question is, will I be letting the switch handle the IP's/DHCP or would I be better off, setting up the server for DHCP? If so, do I also setup the server as the DNS server? From what I am reading online using the server as the DHCP/DNS server gives us more management capabilities and is more "secure". As a test, I loaded Windows Server 2008 R2 on a home machine and played around with this. I got a bit lost on the DHCP and DNS setup and it appears that one needs a Static IP from your ISP in order to setup your serve as the DHCP/DNS server for the domain. Is this correct? I haven't been to his office yet to check out all the existing equipment, is it safe to assume that his ISP provides a router or whatever is needed to feed the switch?
View 3 Replies
View Related
Sep 24, 2011
I am looking to start a proposal for the smallish business I work for. We have about 65 devices on the network with ~ 12 being VOIP phones. Currently our network consists of 2 cisco 2950's and a bunch of daisy chained consumer 5 port switches. I would like to get a couple of 48 port 2960S or 3XXX series catalysis' and run drops to all the devices. It's an older brick building with beamed 15 foot ceilings. It has a couple of semi-enclosed office spaces, with one large space for all the developers and designers. The plan I have involves running a cable tray down the length of the office and run drops off of the main run. I would like to be as cheap as possible with the cable tray, but it seems like all the trays I have seen are about ~50-100 dollars per 10' (not including mounting hardware). Seems extremely expensive for basically wire baskets.
View 3 Replies
View Related
Aug 29, 2012
I need an example of a insecure network configuration that is may occur in small-business.For example insecure devices that can be used or how they are connected with each other. Also router/nas/pc configurations. With wireless network it is easy, but i am not familiar with wired networks. Specially I need weak points of a router configurations and weakly designed connections between different devices.I need to design a insecure small-business network configuration for my school project. For example 2 workstations, 1 laptop, NAS, network printer, VoIP telephone etc. After that I need to analyse these weak points.
View 3 Replies
View Related
Jun 12, 2012
I have a small business with 1 "server PC", 7 PC's & 2 Mac's (and a WiFi TV)Oh and a copier.the server reaches the internet from the wall socket through the copier through a router through a WAP finally to Server. All wired PCs can see the server and interact with it and the copier. All wireless devices (through WAP) cannot access the server computer or the copier. There is no inexpensive way to get a wire to the devices with out causing a tripping hazard or lots of unsightly strung wires. Why are the wireless connections not seeing the server and can I fix that by reconfiguring the setup of my existing devices?
View 6 Replies
View Related
