Cisco Switches :: Multiple VLANs And Relaying DHCP On Two Stacked SGE2000-G5
Nov 17, 2011
We have been set the task of securing a small managed office system which is currently set up with a standard switch allowing each of the offices (containing different companies) to see each other, and in some cases, access each others documents across the network.
Obviously this is a far from adequate set up and our aim is to isolate each office using VLAN's but share a common internet connection provided by the managed offices. We have two Cisco SGE2000-G5 layer 3 switches but we are new to Cisco equipment and VLAN's so we are not quite sure on how to implement this. DHCP would need to be provided by a Router, there is no Server. We are open to suggestions on the Router as we have yet to purchase one.
View 10 Replies
ADVERTISEMENT
Aug 18, 2011
configure a secondary ip address (over the same address range) in a vlan interface on the SGE2000?For example, I want Interface Vlan 10 on mw switch has 172.16.10.1/24 and 172.16.10.2/24. Is that possible? If I try I get an error message with a duplicate IP address error. On Catalyst switches it can be done, but on Small Business?
View 1 Replies
View Related
Sep 18, 2012
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies
View Related
Jun 25, 2012
DHCP Relay on a SGE2000 switch.I have configured two VLANs on the switch, VLAN2 (192.168.10.x/24) and VLAN3 (192.168.9.x/24). I have the switch in Layer 3 mode. I have configured the DHCP relay server of 192.168.10.4 and the DHCP Interfaces as VLAN3. All of the IP Static Routes were generated by the switch.
If I put a client computer on a port that is Untagged VLAN 3 and try to get a DHCP address from the server on an Untagged VLAN 2 port I never get a response back.I have done some packet captures and here is what I have found:
I see the DHCP broadcast on the client computerI see the DHCP Request on the DHCP server coming from the IP assiged to the switch on VLAN 3 (192.168.9.254)I see the DHCP server respond with a DHCP OfferThe DHCP offer never gets to the client computer I can't seem to get a DHCP address to any system not on the same VLAN as the DHCP server. Option 82 is disable and I did try enabling it, which made no difference.
View 2 Replies
View Related
Mar 9, 2010
Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies
View Related
Jan 26, 2013
How to configure DHCP server if i have 2 vlans. I know how to configure rest of the network, just i don't know server.I use packet tracer and i attached file with my network. PC1 is on VLAN1 and PC2 is on VLAN2.I want ip addresses in vlan1 to be from 192.168.1.2 and in vlan2 from 192.168.2.2. I would like to do it just like in the designed network, without router.
View 5 Replies
View Related
Jul 17, 2012
I was looking for configuring QOS for two VLANS i have created. these will be for voice traffic vlan 22 and video traffic vlan23. i also have three other vlans for pc's, wireless devices and our cnc machines. we have 5 switches that are all SG30028P's with a single switch doing the intervlan routing (operating at layer 3). all of the switches are trunked back to the main switch and ive been through the guide written on how to do this on a single switch which i dont think is layer 3.
View 5 Replies
View Related
Aug 20, 2012
I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
View 3 Replies
View Related
Mar 13, 2012
I can not get dhcp to work.I can ping from the switch to both vlans...
here is my config for the router.....
Router is a 1760
Current configuration : 1379 bytes
!
version 12.4
service timestamps debug datetime msec
[Code]....
View 1 Replies
View Related
Aug 26, 2012
I have 2 SG300-10 switches, and I need two VLANs, one for internal network and one for WiFi APs.I need ports 1->4 on both switches to be part of 1st VLAN and ports 5->8 on 2nd VLAN; and port 10 uplink to 2nd switch.How I set up the VLANs and interface VLAN mode?
[code]...
View 1 Replies
View Related
Jun 22, 2011
I am having problems accomplishing these tasks with my new SG 200-18.
I have a LinkSys WRT54G2 connected to port 1. I would like ports 2-8 to be in one VLAN with access to the Internet and to be able to share their printers, hard drives, etc. with other computers on ports 2-8. I would like each of ports 9-16 to be on a separate VLAN with access only to the Internet and no other ports on the switch. I would like to be able to manage the switch from any of the ports 2-8.
After I create the VLAN 1009 (see screenshot below), port 9 can browse the Internet and cannot see the other ports on the switch which is correct. However, ports 2-8 can no longer access the switch at 192.168.1.20 in order to manage the switch.
View 10 Replies
View Related
Jun 21, 2011
I have SGE2010 switches and I want to implement Multiple VLANs. Im a newbie and starting to study VLANS's.
I want to implement 5 VLAN's on my test lab network and here as follows:
192.168.1.x default
192.168.2.x
192.168.3.x
192.168.20.x
192.168.100.x
The .1 is exclusively for my test-lab servers.
The .2 is general test-lab Win-XP workstations.
The .3 is general test-lab Win7 worstations
The .20 is general test-lab production worstations
The .100 is for test-lab IP PHONES.
View 4 Replies
View Related
Aug 19, 2012
I have to configure multiple vlans served with a unique DCHP server . As first step, I just will The DHCP server to serve 2 vlans. The following is the hardware and configuration that I implemented :
[code]...
But If I connect the DHCP server on a trunked switch port and adapt the DHCP server gateway 172.16.0.1 to 172.16.0.254, hosts receive ip address properly.I have to connect the DHCP server directly to the router. How can I do that, what is wrong in the configuration?
View 14 Replies
View Related
Jun 26, 2012
I can't figure out how to configure a port membership with multiple VLANs. My setup:
- VLAN10
- VLAN20
- port settings tab: port24 in general mode
- ports to VLANs tab: untagged everywhere, when I set port 24 membership to VLAN10 I can't set port 24 membership in VLAN20 because when I do that port 24 membership in VLAN10 dissapears and vice versa
- but I can set port 24 membership to both VLANs in VLANs to port tab, but I think it doesn't work because:
- when I connect hosts to ports 23 (port 23 is a member of VLAN10 only) and 24 (member of VLAN10 and VLAN20)
there are not any connectivity between them
- but connectivity is working when I set the same PVID for both ports 23 and 24 in port setting tab, I can't set multiple PVID in here.
So, is it possible to configure port membership for multiple VLANs on this linksys. [URL]
View 1 Replies
View Related
Aug 30, 2011
I have 8 apartments that have a single internet connection coming into the building, I then have a PoE Access Point in each of the 8x apartments.
What I would like to be able to do is to have each apartment within its own vlan, but to be able to use the internet via one of the non-PoE ports (port 9 say) but do not want residents in different flats to be able to see each others devices on the same network.
I have a Cisco SG 300-10MP which has 8x PoE ports and 2x Ethernet ports, one of which my Internet connection is plugged into (using WiMax).
View 2 Replies
View Related
Mar 28, 2012
We have a Cisco 887 router and a Cisco SG-200 switch.We'd like to setup trunking between these 2 devices for multiple VLANs on the switch to be made available on the router.
With previous routers, you could set the router up in the configuration 'router-on-a-stick' and VLANs worked like a charm but the 887 no longer support sub-interfaces.So how can you get trunking working between the 2 devices?
Is there a VTP configuration menu for the SG-200 which we can setup in order for it to talk 'VTP' with the 887 router??
View 1 Replies
View Related
Nov 11, 2012
I am aware that private-vlans are not supported on edge switches like 2960 series - so my question is would it be possibel to ceate private vlans on say just the core switch which would be a 3570 or 4506 that supports private vlans and then just trunk these to the edge like normal vlans?
what I need to achive is to have edge port not able to communicate to each other even across switches - which cannot be done using 'protected' port so need the private vlan feature
View 7 Replies
View Related
Aug 13, 2011
I just received a new Cisco SG300-10 and am configuring it in Layer 3 mode. I am trying to setup multiple routed VLANs going back to a FiOS Actiontec router. My configuration is as follows.
Fios Router: 192.168.1.1
Assigning DHCP 192.168.1.2 through 100.
SG300-10 has VLan 1 ip 192.168.1.5 used for Mgmt.
VLAN2 is 10.0.2.1
VLAN3 is 10.0.3.1.
I have a static route set on the fios router for both subnets setup as follows.
Destination 10.0.3.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
Destination 10.0.2.0 Gateway 192.168.1.5 Netmask 255.255.255.0 Metric 1
I have a laptop connected to Gi8 on the Cisco (Vlan 3) and statically assigned 10.0.3.3, with a gateway of 10.0.3.1. DNS set to the fios router (192.168.1.1).
Everything pretty much works EXCEPT, I cannot get out to the internet from either vlan. Traffic routes between vlans/and the default subnet on the fios without issue.
When I ping out, DNS resolves, but will not go past the fios router. Am I missing a setting somewhere?
View 3 Replies
View Related
Dec 16, 2012
We have 3 SG500-52 switches that are stacked and configured for layer 3 that replaced a couple of SG2010 switches a month ago. Switch units 1 and 2 are for servers and unit 3 for the workstations. The switches are connected with stacking SFP+ copper cables, 1 1M and 2 7M cables. The problems are occurring between the workstations and servers resulting in slow traffic on some links and connection failures. A repeatable failure occurs doing a backup from a PC on unit 3 to a server on unit 1 and 2 (2 port LAG). Moving the workstation to a port on unit 1 results in successful backups every time.
Initially I was able to confirm packet loss between my PC (on unit 3) and the servers using ping (ping -f -c 100000 -s 1460) of about .1%. The iperf program in udp mode also showed some packet loss and in tcp mode showed slow connections. A week ago I then upgraded the switches from v1.2.0.97 to v1.2.7.76 and rebooted. After that the ping and iperf tests show no problems although there are still slow connections to samba shares and the backups still consistently fail.
I suspect there is a problem with the stacking connections and have searched for traffic statistics on the stacking ports to look for errors but have not found anything. Doing a snmpwalk didn't reveal anything that I recognized. There are interface counters for all the ports except the stacking ports.
View 4 Replies
View Related
Jun 26, 2011
I have a Campus LAN setup which is layed out using Cisco SRW2024 and SGE2000 SB switches. On the LAN we are running various services. These are CCTV, VOIP(SIP), Public Address(multicasting) and Internet hotspots to various locations. I have attached a layout of the setup. A unique VLAN is setup for each of these services.The problem we have is that the PA audio is breaking up at intervals making the output distorted this is also happening for the SIP phones within the facility. Using the user guide we have tried to setup QoS on the system but we seem not to improve the services.
View 2 Replies
View Related
May 7, 2013
I have a problem with DHCP. I have two 2960 connected with a port channel on ports 47 and 48 as trunk with native vlan 10. I only have this one vlan. In port 1 of sw 1, I have a C800 as DHCP server.
I have an AP autonomous with single ssid on vlan 10. When I connect the AP to sw1, I receive dhcp with no problems.When I connect the AP to sw 2, I’m not getting IP by DHCP.I have DHCP snooping working on vlan 10 on both devices.
The ports where I connect the AP are access ports on vlan 10 config as trusted.The trunk ports are also configured as trusted.The port 1 of ws 1 that goes to the C800 is also configured as trusted.
figure out why I’m not getting IP by DHCP when I connect the AP to the SW 2.The only I notice is that when I connect the AP to sw 2, I get on SW 1 the message of packet drop by option 82, but even after configuring ip dhcp snooping information option allow-untrusted on both switches, the problem persists.
View 5 Replies
View Related
Aug 22, 2011
I'm having trouble getting a stack of three sge2000 switches to connect together and NOT reboot.Two of the switches are older Linksys sge2000s and they stack well together, but as soon as i connect the new Cisco sge2000, it will make them both reboot sequentially, even though it detects that it needs to be #3 in the stack.SW 1 port 24 is connected to SW 2 port 12 and they function correctly (both of the linksys switches). The documentation states they should be connected in a ring topology so I first tried completing the loop with SW3 (the newer cisco sge2000). When that had the aforementioned troubles I just connected SW2 port 24 to SW3 port 12. Still forcing the switches to reboot.I SUSPECT it may be a firmware/software issue, but I wanted to check if they'ed even work together.
View 2 Replies
View Related
Apr 13, 2013
We are planning to implement the redundant physical connection from 5508 WLC to not stacked 3750 switches. The sheme is attached.
View 7 Replies
View Related
Oct 21, 2012
how i can configure a second ssid for guest access in our environment. this is our network setup prior to this request: Internet----Firewall (not ASA)---ce520---C1131AG and CME router is also connecting to the ce520 switch. we only have two vlans: one for voice and two for data.
Presently, there is no vlan configured on the AP because it on broadcasting ont ssid and wireless users gets IP from a windows DHCP server on the LAN. the configuration on the ce520 switch port for the AP and other switches say access vlan is the DATA vlan which automatically becomes the native vlan for all trunk port connecting the AP and other Stiches to the network.
Now with this new requirement, i have made my research and i have configured the AP to broadcast both the production and the guest Vlans. The two vlans are 20-DATA and 60-Guest. I made the DATA vlan on the AP the native vlan since the poe switch is using the DATA vlan as native on the trunk ports. I configured the firewall to serve as DHCP server for the guest ssid and i have added the ip helper-address on the guest vlan interface on all switches while the windows server remains the dhcp server for the production DATA Vlan. I have confirmed that the AP, switches can ping the default gateway of the guest dhcp server which is another interface on the firewall. I can now see and connect to all broadcasted ssids but the problem is I am not getting IP addresses from both the production dhcp server and guest dhcp server when i connected to the ssid one at a time. My AP config is attached below.
Do i need to redesign the whole network to have a native vlan other nthan the data vlan? Does the access point need to be aware of the voice vlan? Do the native Vlan on the AP need to be in Bridge-group 1 or can i leave it in bridge-group 20?
View 1 Replies
View Related
Jul 1, 2011
We've have a 2 SGE2010-48 port, stacked. 4 LAGS are denifed, two on primary, whitch are working, two on slave unit are NOT working. Devices connected to LAGS are de the same and same configuration (Cisco ASA 5510).
View 3 Replies
View Related
Nov 15, 2011
I have a 4 member stack of 3750's. We would like to take advantage of wccp and we understand that we will need to upgrade our switch licensing from IPBase to IPServices. My question is do we need to pay for a license for each member in the stack or does one IPServices license upgrade cover the whole stack?
WS-C3750G-48PS
WS-C3750G-48TSWS-C3750G-48TSWS-C3750G-48TS
View 1 Replies
View Related
May 10, 2012
I am about to buy 2x Series 500 switches but before that I have a design to be sure :I want to create a redondant network so it is the reason why I want to stack 2x Series 500 switches.Each server on my network (ESX and Windows 2008) are connected with two NIC (one port on the first switch , one port on the second switch), with trunk mode + etherchannel for LACP.
First question : I saw that the limitation is up to 8 etherchanel groups, can I have a mix of multiple servers on the same etherchannel group or should I create one etherchanel group for one server with only the two NIC inside?
Second question:I want to use the series 500 to do intervlan routing and want to be sure that if the the ports are in trunk mode with some vlan set on the card itself that the default gateway for the vlan will be propagated on the two switches (in stack mode) and will not cause any issues when both switchs works fine and if one switch crashes?
View 3 Replies
View Related
May 28, 2012
How many Switches can be stacked with WS-C2960S-48FPD-L at a max..
As per my Knowledge it is 4 and as below..
Switch 1 to Switch 2
Switch 2 to Switch 3
Switch 3 to Switch 4
Switch 4 to Switch 1
If yes then, is it mandatory to do the "Switch 4 to Switch 1" stack. why am I asking this is because this stack requires a long cable and the cable which comes with the Switch is only 0.5M.
View 3 Replies
View Related
Nov 14, 2012
Can MGBSX1 transceivers use on SGE2000? what type of transceivers can be use on SGE2000.
View 1 Replies
View Related
May 10, 2012
What is the difference between a SGE2000 and a SG500-28?
View 3 Replies
View Related
Jul 17, 2012
I am running the SGE2000 as my l3 core switch with multiple inter-vlans.
have a customer requirement that needs to restrict eg. GUEST-VLAN10 to all other VLANS in the network. Only allowing access to the internet.
It seems on the switch i am able to bind ACL to per port interface. if this is possible on the SGE2000
View 4 Replies
View Related
Apr 2, 2012
My company is beginning to have a lot of sites were we are stacking 3 to 4 C2960S-48 switche.This is making "show running-config" very very long because of the 4 x 48 interfaces.I can’t find a CLI command that show me the running-config of a ranges of interfaces. If I for example would like to see running-config for switch 3 (interfaces 3/0/1-52)The Show Running-config will show all the interfaces (for the two first swtiche = 104 interfaces), which take a time before I reach to switch 3.I miss a CLI command like: show Running-config switch 3, or module 3, or show running-config interface range x/x/x-x ?I’m well aware of the CLI command show running-config interface x/x/x, but this will only show me one interface.
View 3 Replies
View Related
Feb 25, 2013
I have two 3750x stacked switches , both with the latest firmware on them. I enter the configuration onto one switch and it obviously copies over onto the other switch. Although in the configuration I have both a console username and password and an enable password, when I try to log onto the initial switch that I entered the configuration on, I am prompted for a username and password, which works fine, but when I try to enter enable mode i get an error stating that no password has been set. However when logging onto the other switch I am not prompted for a username or password but when I try to enter enable mode I am prompted for a password and can access it with no problems.
View 1 Replies
View Related
