configure a secondary ip address (over the same address range) in a vlan interface on the SGE2000?For example, I want Interface Vlan 10 on mw switch has 172.16.10.1/24 and 172.16.10.2/24. Is that possible? If I try I get an error message with a duplicate IP address error. On Catalyst switches it can be done, but on Small Business?
View 1 RepliesWe have been set the task of securing a small managed office system which is currently set up with a standard switch allowing each of the offices (containing different companies) to see each other, and in some cases, access each others documents across the network.
Obviously this is a far from adequate set up and our aim is to isolate each office using VLAN's but share a common internet connection provided by the managed offices. We have two Cisco SGE2000-G5 layer 3 switches but we are new to Cisco equipment and VLAN's so we are not quite sure on how to implement this. DHCP would need to be provided by a Router, there is no Server. We are open to suggestions on the Router as we have yet to purchase one.
We've been trying to monitor the used bandwidth of our SGE2000 and SGE2010 switches with Nagios.We've been experimenting with the various OIDs and we've found the OIDs linked to the different switchports.
Though when we use SNMPWalk (to find the OIDs connected to the port) the names of the ports are all the same.
[code]....
Is there a way to change the names of these interface to unique names?We've already given unique names in the description field through the switch's GUI, but it doesn't make any difference for Nagios.
We have a standalone Cisco SGE 2000.
We lost connectivity to the web user interface - it no longer responds on the configured IP address.From the manual we see that by default the switch get its IP address via DHCP - but we find no record of any ip address assigned to this switch.Is there a IP address that this unit defaults to when DHCP is not available? Also - what is the best way to connect to the console using Windows 7?
I have a Campus LAN setup which is layed out using Cisco SRW2024 and SGE2000 SB switches. On the LAN we are running various services. These are CCTV, VOIP(SIP), Public Address(multicasting) and Internet hotspots to various locations. I have attached a layout of the setup. A unique VLAN is setup for each of these services.The problem we have is that the PA audio is breaking up at intervals making the output distorted this is also happening for the SIP phones within the facility. Using the user guide we have tried to setup QoS on the system but we seem not to improve the services.
View 2 Replies View RelatedI'm having trouble getting a stack of three sge2000 switches to connect together and NOT reboot.Two of the switches are older Linksys sge2000s and they stack well together, but as soon as i connect the new Cisco sge2000, it will make them both reboot sequentially, even though it detects that it needs to be #3 in the stack.SW 1 port 24 is connected to SW 2 port 12 and they function correctly (both of the linksys switches). The documentation states they should be connected in a ring topology so I first tried completing the loop with SW3 (the newer cisco sge2000). When that had the aforementioned troubles I just connected SW2 port 24 to SW3 port 12. Still forcing the switches to reboot.I SUSPECT it may be a firmware/software issue, but I wanted to check if they'ed even work together.
View 2 Replies View RelatedWhy layer 2 switches need its mac address, even it does not have any interface ? (does not have stp and etc)
View 8 Replies View RelatedI was given a linksys SRW224G4 switch .. It seems to work fine on some ports and others dont,I am tring to log into it to see what the current config is . I cant seem to find what ip address its pulling to be able to log into the web interface. I have tried the blue cable , and using hypertermail but with no luck .. I dont have com 1 or 2 as an option on my latop just com 3. how I can log into this switch and rest it back to factory specs so then I can go though and setup how i want.
View 4 Replies View RelatedCan MGBSX1 transceivers use on SGE2000? what type of transceivers can be use on SGE2000.
View 1 Replies View RelatedWhat is the difference between a SGE2000 and a SG500-28?
View 3 Replies View RelatedI am running the SGE2000 as my l3 core switch with multiple inter-vlans.
have a customer requirement that needs to restrict eg. GUEST-VLAN10 to all other VLANS in the network. Only allowing access to the internet.
It seems on the switch i am able to bind ACL to per port interface. if this is possible on the SGE2000
Searched through conference and still have no resolution.Switch: Cisco SGE 2000..Layer3 mode enabled through console. [code]
View 3 Replies View RelatedI'm trying to get a network of SGE2000 switches mapped into Cisco network assistant.It always comes back with the device type unknown and status unsupported device.Is there a way to fix this ? I'm using Cisco network assistant ver.5.7(6)
View 4 Replies View RelatedWhere I could find an SGE2000 visio stencil? It isnt listed in the Cisco Visio Stencil page?
View 1 Replies View RelatedDHCP Relay on a SGE2000 switch.I have configured two VLANs on the switch, VLAN2 (192.168.10.x/24) and VLAN3 (192.168.9.x/24). I have the switch in Layer 3 mode. I have configured the DHCP relay server of 192.168.10.4 and the DHCP Interfaces as VLAN3. All of the IP Static Routes were generated by the switch.
If I put a client computer on a port that is Untagged VLAN 3 and try to get a DHCP address from the server on an Untagged VLAN 2 port I never get a response back.I have done some packet captures and here is what I have found:
I see the DHCP broadcast on the client computerI see the DHCP Request on the DHCP server coming from the IP assiged to the switch on VLAN 3 (192.168.9.254)I see the DHCP server respond with a DHCP OfferThe DHCP offer never gets to the client computer I can't seem to get a DHCP address to any system not on the same VLAN as the DHCP server. Option 82 is disable and I did try enabling it, which made no difference.
Does the SGE2000 supports NetFlow? I've checked the Cisco docs and also called Cisco support to which no one has been able to answer me.
Anyhow, just in case it doesn't support NetFlow, how to be able to set up something that would be able to check the bandwidth usage on each port?
I've got a problem where I think the SGE2000 switch is failing when I pump around 190~200Mbps through x2 of the ports (Server A on port 1=130Mbps and Server B on port 2=60Mbps) of Multicast traffic (UDP). I can measure the output from the Streaming servers that provide the multicast content, thats how I know the input to the switch and I know that there are no packets lost or any errors departing from the servers, yet when I increase server B to say 80Mbps, I get break up and all sorts of problems on the client end STBs and it is happening on the multicast content provided by Server A too which is a different source, so I'm 99.9% sure its a SGE2000 switch problem which is why I'd like to monitor it somehow.
I´ve got a strange problem with the connectivity within a ring topology.There are five switches from the SGE2000 series and one SG200-50.The SG200-50 is the root bridge and RSTP is configured.From the root bridge switch (Switch 5) I can ping Switch 0.But I cannot ping Switch 0 from PC0.
On the other hand I am able to ping all other Switches (1-5) from PC0.In addition to that I can establish a RDP connection from PC0 to Server0.This tells me that there is no general problem with the connection from PC0 to the Switch0.
Right now when I want to configure Switch0 the only way is to connect to Server0 first.But we have to move Server0 and this is why I want to manage Switch0 from PC0 like any other Switch on that network.
I am trying to assign static ip address on vlan 1 interface , the model no of switch is SG300 & the firmware version is 1.1.2.0 .But whenever I type the IP address & press enter , a question is popped up asking for confirmation (switch0d851f(config-if)#ip address 1.1.1.1 255.0.0.0.
Please ensure that the port through which the device is managed has the proper settings and is a member of the new management interface.Would you like to apply this new configuration? (Y/N)[N] N )
I am the Systems Admin at LDM Media and am trying to get some support for one of the SRW224G4 managed switches we have in our rack. The issue is as follows:
Any endpoint connected to the switch is assigned an IP address in the range of 169.254.154.XXX regardless of the switches set IP range, the second issue is that I cannot access the web view management interface through the default IP address 192.168.1.254 (and I have tried to use the last IP in the range set by the router 169.254.154.254, to no avail)
How to regaining control of this supposedly smart switch?
We have a couple of cisco SGE switches connected to a single DELL, between the cisco switches we have a trunk interface. I'm not sure which setting should be configured on the switches to get it working because a loop is occuring.
View 1 Replies View RelatedI currently am using the SGE2000 switches for our datacentre and they have run great. We are looking at replacing them as part of our normal equipment refresh and have questions about what is the best switch for us. We are looking at upgrading to at least 48 port switches which isn't a huge issue.The main purposes of the switches will be for iSCSI traffic between Starwind SANs and Vsphere 5.1 hosts. We had some latency issues with one of the SGE2000s but otherwise they've been great.
We also will use these switches to handle our feeds from our ISP and our normal interserver communications. We have had DDoS attacks in the past of 40k packets per second and 600mbps and the SGE2000 never even flinched. We don't need it for any layer3 routing (which we use virtualized PFsense for). Looking at the Miercom report the SG200 series looks like it would be fine for us but I'm just worried around the part which mentions it becoame unresponsive in a DoS attack and also whther it may be slower for iSCSI. Both series seem to support flow control and jumbo frames.
I have a Linksys SGE2000 Switch and I've been trying to get Vlan's to work.How I'm trying to setup is like this
Port 1 - Vlan22 - Plugged into trusted port in firewall
Port 3 - Vlan25 - Plugged into DMZ in firewall
Port 15 - is plugged into a VMWare host. The network is setup as production is Vlan 22, DMZ is Vlan 25.
Port 16 - Internal server so is Vlan 22
Both Vlans have a different IP subnet.I think I have port 3 configured ok as it's only one Vlan. I'm trying to get Port 15 configured properly and it won't work.Servers on VMWare hosts are Windows Server O/S.
I am trying to update the SGE2000v1.0 with 24ports to 3.0.1.0: url...I got the error "illegal software format" using tftp.
View 2 Replies View RelatedThe switch sge2000-g5 a small business switch, has a redundant power supply port built in the switch. It is a port that handles a 12v power supply. My problem is to find the exact device to supply the power to this port so I can have, obviously, a redundant power in my switch. This switch is actually out of production.
View 1 Replies View RelatedI was looking for configuring QOS for two VLANS i have created. these will be for voice traffic vlan 22 and video traffic vlan23. i also have three other vlans for pc's, wireless devices and our cnc machines. we have 5 switches that are all SG30028P's with a single switch doing the intervlan routing (operating at layer 3). all of the switches are trunked back to the main switch and ive been through the guide written on how to do this on a single switch which i dont think is layer 3.
View 5 Replies View RelatedI'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View RelatedI'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?
View 1 Replies View RelatedMy internet router acts as an IGMP Proxy for the LAN and distributes IPTV there. The router is connected to one of my three SG 300 10 Cisco switches (connected to one another via uplink port). Now I want all switches to send multicast traffic to only the recipients of such traffic (PCs with VLC and Network Media Players) connected to either one of them. How do I have to configure the switches to do so and not flood the LAN with multicast traffic, is it enough to enable IGMP Snooping on each switch?
View 2 Replies View Relatedwe just received 5 new SF200-48 Smart Switches for small business. I noticed only way I can configure them is by using the web gui. Is there a way to enable good old CLI?
View 6 Replies View RelatedWe are in the process of adding second isp for webhosting purposes .Is there any issue if we are making outside 2 interface on the pix .i need to host some websites through this new link ie isp2 .
PIX Version 7.0(7)
We have Cisco ASA 5505 box.We have a /29 subnet available.At this moment one of IP addresses in this rage is assigned to VLAN2 used for outside interface all outgoing traffic from VLAN10 (for employees) will go out using one IP, xxx.xxx.xxx.1all outgoing traffic from VLAN20 (for visitors) will go out using second IP, xxx.xxx.xxx.2all outgoing traffic from VLAN10 host yyy.yyy.yyy.yyy (mail server, webmail, ...) will go out using third IP, xxx.xxx.xxx.3all specified incomming traffic to xxx.xxx.xxx.3 will be NATted to internal host yyy.yyy.yyy.yyy in VLAN10 .The main purpose is to have specific public IP address for mail server only not to get to any black list,and to give visitors different outgoing IP address than for our internal users.
View 3 Replies View Related