Cisco Switches :: SRW224G4 - Cannot Access Web View Management Interface Through IP Address
Jul 12, 2012
I am the Systems Admin at LDM Media and am trying to get some support for one of the SRW224G4 managed switches we have in our rack. The issue is as follows:
Any endpoint connected to the switch is assigned an IP address in the range of 169.254.154.XXX regardless of the switches set IP range, the second issue is that I cannot access the web view management interface through the default IP address 192.168.1.254 (and I have tried to use the last IP in the range set by the router 169.254.154.254, to no avail)
How to regaining control of this supposedly smart switch?
View 3 Replies
ADVERTISEMENT
Feb 2, 2012
I was given a linksys SRW224G4 switch .. It seems to work fine on some ports and others dont,I am tring to log into it to see what the current config is . I cant seem to find what ip address its pulling to be able to log into the web interface. I have tried the blue cable , and using hypertermail but with no luck .. I dont have com 1 or 2 as an option on my latop just com 3. how I can log into this switch and rest it back to factory specs so then I can go though and setup how i want.
View 4 Replies
View Related
Oct 19, 2011
I have got a 3502 setup and functioning in Office Extend mode. I have found one issue though. I have to set the checkbox on the my Management Interface to Enable NAT Address and put the external address in the box. Once this occurs no internal APs can join the controller.
Need setting this up with a single controller behind a router and not having to set the NAT Address for the Management interface? Should I setup a second interface on the controller to be for external management?
View 9 Replies
View Related
Dec 21, 2012
I have a new SG300-28P, and have had occasional issues with being unable to connect to it via anything other than the serial port. I have connectivity between my machine and the switch (tested with ping each way), and in fact, have the same problem if I take a laptop to the switch and connect them directly.What happens is that though the switch is operating normally, http, https, ssh and telnet attempts to access all fail in one way or another. Ssh and telnet either yields no response or a refused connection (even though those services are enabled). For http and https, I'll occasionally get enough of the web page to be able to tell what it is ... but attempts to log in just don't work.While this is happening, the CPU and packet load on the switch is very, very low.Rebooting didn't work entirely, though it may have made it better. Resetting to factory defaults and then reconfiguring makes it work.This is using the latest firmware: 1.2.7.76.
View 3 Replies
View Related
Jun 13, 2012
How to set the management interface on a SG300 Switch in Layer 3 mode? I've some vlans configured on the switch with interfaces in each of them:
Vlan 100 (10.0.1.254 /24)
Vlan 200 (10.0.2.254 /24)
Vlan 300 (10.0.3.254 /24)
...
Vlan 900 (10.0.9.254 /24)
Now, the management interface is listening on all interfaces (IPs). But I would like to configure the switch to only listen on 10.0.9.254. What I need to configure or whether it is possible?
View 3 Replies
View Related
Jul 31, 2011
I volunteer at a school who just purchased two 48 port SGE2010 managed switches. I am not a big fan of the web gui and was hoping to see the standard Cisco command prompt instead of the menu-type interface.
Is there a way to view the MAC table showing which MAC address is plugged into which port on the switch? I have been fighting with the menu and the gui for a while now and do not see this anywhere.
View 5 Replies
View Related
Jan 19, 2013
I'm trying to upgrade a switch SRW224G4 but without success. Model Name SRW224G4 Hardware Version 00.03.00Boot Version 1.0.0.06
I send the file via the XModem( SRW2xxG4_FW_1.2.3.0 ).
View 2 Replies
View Related
Jan 16, 2013
After I've upgraded software to the v7.3 and applied AP-SSO it made imposible to access the controller's gui via Service-port. So we tried to access it by management-port, but there is some problem too. It is not working from another subnets. But default gateway on management vlan is set correctly and I even tried to turn of all acl's on switch. WLC is only accessible from the same network. But at the same time wlc is replying on ping fine.All other protocols cannot connect to the controller.
View 3 Replies
View Related
May 24, 2011
I was wondering if there was a difference between the Linksys SRW224G4 & Cisco SF300-24 switches. Going through the support docs I see the SF300 has limited L3 functionality in terms of being able to establish static routes between VLANS. Any further information would be of use.
View 2 Replies
View Related
May 8, 2013
After some wireshark, I see that when I have a vLan on the switch, only win7 gets IP, my macbook doesn't, sniffing to the bootp, I see that the DHCP sends NAK and after I only have DISCOVER & OFFER...
When I get the same switch and the same router and take out the vLan on the switch, everybody get an IP. What's the deal with this switch and vLans and Mac OS x ? Do I have to setup something else ?
View 1 Replies
View Related
Oct 30, 2012
i cannot access the web managemnet interface of this router from a different subnet.THe WAN interface is a 4G LTE connection,I have disabled both the SPI firewall and NAT and enabled remote management from any ip address but i cannot access the admin web page from a remote subnet.Doing a port scan of the routers WAN or LAN address i cannot see any ports open at all...its as if firewall or NAT is still enabled somehow.
View 0 Replies
View Related
Apr 3, 2013
I configure IP address on the management interface port 1 of 5508 controller when i connect it direct to my laptop i can't ping or access controller from my laptop even i connect through layer 2 switch still i can't not.
IP Address of management interface : 10.21.0.50
Laptop IP Address : 10.21.0,51
View 13 Replies
View Related
Jul 28, 2009
I have a switch SRW224G4 from Linksys and doesn't work now after an firmware upgrade!
Simple, here the result when I try to install the firmware "ls_106-12216.ros" or "SRW224G4P_SRW248G4P_image_v1020.bix" that came from your web site!
Here the result for "ls_106-12216.ros"
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>
[Code].....
View 12 Replies
View Related
Jun 8, 2011
I've got an ASA 5505 running 6.3 I've connected the management interface to our management vlan (which contains switch IPs, ilo's etc)Is there a way to allow access to this vlan from another?
View 1 Replies
View Related
Aug 15, 2012
We have small network with 15 Computers all connected to SRW224G4 . After a power brake our switch dosent "boot" anymore. I see all leds working flashing etc but no network acces, no Serial acces. When i try connecting to serial port and "reset" device the screen is blank.
View 1 Replies
View Related
Aug 30, 2011
I've got a new 5508 wireless lan controller and can ping the ip address of the management interface, but can't access the GUI at the management interface's ip address. I can access the GUI on the service-port interface. No static routes in the controller; trunk appears to be set up correctly.
View 5 Replies
View Related
Mar 25, 2012
I have a SG300 switch working in layer 3 mode. I created 3 VLANS and the intervlan communication is working fine. I want to know how to block acces to switch managment from the Vlans. One of the vlan is allowed to access the switch but not the others vlans. What is the best way to implement this? with ACL or with Managment Access Method, creating an access profile?
View 1 Replies
View Related
Dec 27, 2011
Why layer 2 switches need its mac address, even it does not have any interface ? (does not have stp and etc)
View 8 Replies
View Related
Apr 29, 2012
We've got a SG200-18 switch that is to be used as a workgroup switch in our environment (SW Version 1.1.1.8). Working with CLI on big and mid-range Cisco-gear over the past two decades I'm having a hard time figuring out the following on the SG200:
o) I want to change the Management-VLAN from the default "1" to the management-VLAN used in our environment. Sure enough I created that vlan in the SG200-config, however when it comes to assigning the management-IP and VLAN for the management interface in the corresponding pulldown under "IPv4 interface -> Management VLAN" the only thing selectable is the default "1". (see screenshots enclosed)So how do I set a management VLAN different from 1?
o) How do I enable telnet/ssh-access to the SG200-18 - I'd be far more comfortable with a CLI-environment?
View 2 Replies
View Related
Aug 18, 2011
configure a secondary ip address (over the same address range) in a vlan interface on the SGE2000?For example, I want Interface Vlan 10 on mw switch has 172.16.10.1/24 and 172.16.10.2/24. Is that possible? If I try I get an error message with a duplicate IP address error. On Catalyst switches it can be done, but on Small Business?
View 1 Replies
View Related
Dec 13, 2011
I am trying to assign static ip address on vlan 1 interface , the model no of switch is SG300 & the firmware version is 1.1.2.0 .But whenever I type the IP address & press enter , a question is popped up asking for confirmation (switch0d851f(config-if)#ip address 1.1.1.1 255.0.0.0.
Please ensure that the port through which the device is managed has the proper settings and is a member of the new management interface.Would you like to apply this new configuration? (Y/N)[N] N )
View 3 Replies
View Related
Aug 8, 2011
How can I access the we interface of this switch if it is configured to get its IP address from the DHCP server? Since it is DHCP I do not know what IP address has been assigned to it therefore I do not know what ip address to enter in the browser.
View 9 Replies
View Related
Jun 17, 2012
I've been trying to configure a TP-Link L-WR740N to act as an access point using the instructions here as a guide. As stated in the guide, I've been changing the IP address of the TP-Link router to a new address that lies outwith the pool of available DHCP addresses in my combined modem/router but with less than resounding success. After rebooting the TP-Link router, I am unable to access the set-up interface - the newly allocated IP address doesn't work, neither does the original IP address work. What is happening here? If I change the IP address to one that lies within the DHCP pool and reboot, I can access it ok with the new address. However, that obviously clashes with the set-up instructions.
View 1 Replies
View Related
Sep 10, 2012
I'm configuring a 5505 for a remote office. Until they are assigned a static ip by the provider I will have to use the providers dhcp address. How do I construct an access list for the outside interface using the external address if I don't know it yet? is there a commnd that will insert the ip address in to the access list once one is assigned?
View 5 Replies
View Related
Aug 7, 2011
Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies
View Related
Nov 5, 2012
I'm trying to separate my management traffic from regular traffic by splitting the management and "outside" interface to separate vlans but I'm hitting a routing issue. Say I have have a management network of 192.168.1.0 255.255.255.0 running across vlan 1 and I want to use 192.168.2.0 255.255.255.0 running across vlan 2 for the outside interface to send all the other traffic excluding the management traffic across. Tag both vlans on the external interface, say Eth0/0 Default route of route outside 0.0.0.0 0.0.0.0 192.168.2.1, With this, you can not hit the management interface because there is no route defined for the 192.168.1.0 network. However of course if you try to set one, you'll get the "connected route exists" error. How can I set the default route or gateway of the 192.168.1.0 network on the ASA. Switches just don't complain like the ASA does.
View 8 Replies
View Related
Dec 3, 2012
We acquired recentlty a new Cisco 6509 with Sup-2T supervisor card
My question is the following : we have a management subnet on a Copper-based switch; we manage all equipments through this network. I planned to configure the management interface on the 6509 to connect this switch & monitor the VSS through it However, since it is a CMP interface, most of the actions (SNMP, IOS upgrade.. won't be possible through this link) Moreover, I don't think LMS would be able to get the configuration through it (except by configuring a script running "attach" command & show run
Is there something I miss or must I add another interface of the Catalyst to this network (the problem being that I have no copper line card)
View 2 Replies
View Related
Jan 27, 2011
We have recently purchased a Cisco Small Business Pro SRP 527W router, all seems good and it is running smoothly, no disconnections or sync issues like our last router. However, after a certain amount of time the web management interface is unavailable through the browser (accessing it via 192.168.1.254 or the alternative we set-up 1.1.1.1) It is totally unavailable and timeouts in the browser yet there is still internet access and network is still alive. The web management interface was accessible before though and the only solution I have been able to do to access it again is to reboot this router.Could it be possible that because port 80 is forwarded to a different IP it interferes with the Web management interface? And how wcould the interface port access be changed?
View 2 Replies
View Related
Jun 7, 2011
I have running a Wireless LAN Controller Cisco 2006.Today my management IP its public with Internet access. I am thinking in use a private IP without internet access. I have certains Access-Points in other building, that connect to AP Manager interface using Internet . When i see the tcp connections, i look that the access-point not only have TCP connections to AP Manager interfaces, it have TCP connections to Management interface too!!!.If i shutdown the connection between Management interface and Access-Points (mantaining the connection between Access-Point and AP Manager interfaces)?
View 1 Replies
View Related
Apr 25, 2012
Am trying to replicate the managment interface functionality of a CSS on ACE 4710 but have problem with it being treated as a general routed interface.
Scenario
On ACE 4710 I have a front-end interface for client facing VIPS and a back-end interface facing a server farm, taking care of load balancing flows
Non load-balance system traffic for the back-end servers also flows through these two ACE interfaces, following a default route path (the back-ends use the ACE as default gateway) i.e. dns requests from the servers flow through the ACE egressing the front-end interface to hit a firewall and route to an internal dns server.
Issue
If I add a "management interface" to the ACE 4710 and give it an IP address for management access, the interface by default assumes 'routed' mode and as the ACE treats this as a general interface it will route traffic out of it. For example if the IP address of this management interface is on the same network as the internal dns server, it breaks that connectivity. This as the ACE will see the "management" interface as best route to directly connected network and send traffic to dns server over that, however dns server response traffic will follow its defult route path via firewall and ACE front-end interface to get reply to back-end server. The firewall will block this traffic as traffic is asymmetrically routed and firewall not seen the initial dns request packet.
Question
Is there a way of making an ACE interface a 'non routed' management only interface for out of band management use? That is ACE will not attempt to route general traffic through the interface
I realise I could achieve this with multiple contexts but want to have a single context for various reasons - i.e. to have a kind of like for like CSS replacement using ACE 4710
View 3 Replies
View Related
Feb 13, 2012
I am having issues with the ASA 5510 management interface. I can't communicate with this interface. It is showing DOWN/DWON even if I type NO SHUT several times.
My existing config is as follows
our-asa-01# sh run
Saved
ASA Version 7.2(5)
hostname our-asa-01
names
dns-guard
interface Ethernet0/0
[code]....
View 5 Replies
View Related
Apr 29, 2011
I try to access my router web page with a correct address (192.168.1.1) but on my computer i have this message {Network Error (tcp_error)} but i can access this page from another computer through the network (WHY)
View 1 Replies
View Related
Jun 30, 2010
How to configure SSH on a ASR 1002 and apply it to the Management Interface?
View 3 Replies
View Related
