I'm configuring a 5505 for a remote office. Until they are assigned a static ip by the provider I will have to use the providers dhcp address. How do I construct an access list for the outside interface using the external address if I don't know it yet? is there a commnd that will insert the ip address in to the access list once one is assigned?
View 5 RepliesI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 7 Replies View RelatedWe have an ASA 5505 and are changing ISPs so we'll be getting a new static IP address. How do I change the external IP address using ASDM? (I haven't done it in 5 years so I'm rusty and just want ot make sure.) The ASA and ASDM are up to date.Am i correct in that I only need to change the external address in the configuration under Interfaces, then under Routing - Static Routes - Gateway IP I just need to enter the new WAN gateway address?
View 2 Replies View RelatedI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 5 Replies View RelatedI have a couple of ASA 5505's which work fine for what they are doing VPN and all that - we have 1 DLINK DFR-700 Firewall left and I need to get a new ASA to replace this since it is old.
All this box really does is port forward external clients to 1 address on the internal lan for client software updates. Any example configs?
So lets say we have client a with IP 1.1.1.1 and client b has 2.2.2.2 - at the moment this is what happens client a and b come in through http and get mapped to the internal http server 10.10.1.2
So I need to setup about 100 clients which can come in through http only - get mapped to the internal IP and also keeping the internal server to be able to access anything outside.
I have a router in front of a few firewalls on an internet link. All traffic from the inside network must go through one of the firewalls to get out through the router and similarly there is a dmz on one of the firewalls.I am trying to make sure the router is fully hardened.Should I apply an access list on the outside interface of the router along with the access list for management access?
View 11 Replies View RelatedThis is a working example using static. But it doesn't work with the dynamic interface or I'm doing something wrong. Need to get rdp access to my laptop.
ASA Version 8.4(5)6
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]...
I have a cable modem internet connection and my cable modem is connected to an ASA 5505. The inside interface of the ASA has an IP address of 192.168.2.2 and is connected to a Linksys router's internet port which has an IP address of 192.168.2.1. The Linksys router then has a local area network of 192.168.1.0 and all my clients are on that network. Everything is working fine except in my ASA logs all the traffic shows up as the router's external address which is 192.168.2.1. I would like to see the 192.168.1.x address of the clients in the ASA firewall. I've tried making some changes to the Linksys router but that hasn't resolved it. Is there any changes I can make on the ASA to get this to work?
View 6 Replies View RelatedASA 5505 vlans routing & access-list?
View 4 Replies View RelatedIs there any way of showing the currently assigned ip address for an interface configured to use DHCP on an ASA 5505?
View 2 Replies View RelatedWe have an ASA 5505 running version 8.4. We are having problems allowing external traffic to access computers behind the firewall. Our current config is:
ASA Version 8.4(3)!hostname ciscoasadomain-name default.domain.invalidnames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 10.2.1.1 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 152.18.75.132 255.255.255.240!boot system disk0:/asa843-k8.binftp mode passivedns server-group DefaultDNSdomain-name default.domain.invalidobject network a-152.18.75.133host 152.18.75.133object network a-10.2.1.2host 10.2.1.2object-group network ext-serversnetwork-object host 142.21.53.249network-object host 142.21.53.251network-object host 142.21.53.195object-group network ecomm_serversnetwork-object
[code]....
I have a issue that i am at a loss as how to solve it. I have an ASA 5505 as my firewall. I have users from other companies who visit from time to time and are unable to use their outlook email to send messages. They can however receive messages without a problem. I also have a situation where users who use windows live to access gmail are unable to send messages.
I have narrowed it down to the fact that these uses are using ssl/tls to send the mails. I did some research and found out about the inspect esmtp setting in the ASA. I have disabled it and i still have to problem. I have also removed all outbound deny statements and still no luck.
Of note is that i can send emails without attachments. They take a long time to go out ( from minutes to hours) but eventually they do. Emails with attachments of even 10k do not go at all.
I was running image 8.2.3 and i downgraded to 8.0.5...still did not work...i upgraded to 8.4.3...still did not work. I am now back at 8.2.3.
My Firewall config is attached. I am at my wits end as to what else to try. The company has not renewed support for the device so i am on my own here!
I am having difficulty following the logic of the port-translation. Here is the configuration on a 5505 with 8.3,So I would have thought the outside access-list should reference the 'mapped' port but even with 3398 open I cannot remote desktop to the host. If I open 3389 then I can connect successfully.
View 12 Replies View RelatedI would like to allow users from network 10.132.23.0/24, 10.132.33.0/24, 10.132.24.0/24 access to our SQL server(192.168.1.7) located on the inside interface(192.168.1.0/24 network) Those networks (10.132.0.0/16) come from the DMZ interface.
View 12 Replies View RelatedI am having a problem configuring my ASA 5505 for NAT.
View 3 Replies View RelatedI've got an ASA 5505 running 6.3 I've connected the management interface to our management vlan (which contains switch IPs, ilo's etc)Is there a way to allow access to this vlan from another?
View 1 Replies View RelatedI just purchased a domain name, that I have forwarding to my WAN address. I want to be able to access my home websie via this route. I have an ASA 5505, how do I get the ASA to point to the home server when the WAN IP address is entered?
View 16 Replies View RelatedHow to apply access list on Vlans ?
my Scenario is
13 Vlans in cisco 3560 switch (Vlan 10,20,30........ 130)
vlan 10 ---- ip range 192.168.10.0/24 interface vlan 10 ip add : 192.168.10.1
vlan 20 ---- ip range 192.168.20.0/24 interface vlan 20 ip add : 192.168.20.1
here i want to block vlan 10 access to vlan 20 i created extended access list deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
and applied in interface vlan 10 as out now i cant able to access any host in vlan 20 (host 192.168.20.1) but i can able ping vlan 20's gateway 192.168.20.1
I have one computer connected to the 4506 that management does not want this PC to have access to anything on our network except our DHCP server and the one printer that resides on our network. I created an extended access list as follows. Our network is the 10.10.x.x and the external addresses the PC needs to access is 11.1.x.x. Once this PC is rebooted, it is unable to access DHCP to get the needed IP address it bounces back to a 169.x.x.x address and stops working.
Extended IP access list 2000
permit tcp host 10.10.200.242 host 11.1.200.1 (gateway)
permit tcp host 10.10.200.242 host 11.1.2.151 eq smtp (access from the pc to external server for smtp)
permit tcp host 10.10.200.242 host 11.1.2.149 eq 5721 (access from the pc to external server for remote access)
[ code]...
Then I applied the access-group 2000 on the interface the PC is connected to. What am I missing for DHCP to work and for this PC to always get the ip address that is reserved?
I am trying to harden my Nexus box and I am not able to ACL assigment command. Following are the commands I am trying to add.
interface cmp-mgmt module 5
Ip access-group NETWORK_MANAGEMENT_ACCESS in
We have a three tier network with a centralized core switch and multitple distirbution swithces - all 6506 routers.EAch dist switch is its own PIM SM domain and the RP so we never send multicast between the dist switches and through the core.
We are putting in a centralized server at the core switch which has to provide specific mcast < X Groups > to all servers at the dist level on all dist switches.
So we would like to define the RP <core rp ip> just for the <X groups> on the Core switch and tell all the distribution switch that the core is the RP for just the <XGroups>
If we put these commands on all the switches including the cores will that set the rp just fo the <XGroups> to the <core rp ip > ?Do I have to define the deine an ACL for all groups if i define it for some or will groups not defined by the ACL defualt to the local RP?
do I have to put in the override command ? (We are using MSDP not autorp)
ip pim rp-address <distn rp ip>
ip pim rp-address <core rp ip> 99
ip access-list 99
permit <XGroups > mask
I've setup my VPN on the cisco ASA 5505 which works perfectly, users from outside can access my internal LAN. Now what i want, Is to create another VPN Tunnel group with another set of IP in which i want to allow them access to one server inside our LAN. See below details of network. [code]
View 1 Replies View RelatedHow to list ports open on Cisco ASA 5505 appliance? I have tried to see using Cisco ASDM launcher, but no luck.
View 1 Replies View RelatedI have two ASA 5510 in an active-standby cluster, not that I think that the fact that they are clustered will be of any importance here so feel free to think of it as a single 5510. The internet connection is delivered in a single RJ45 connection. To be able to use it with the cluster there is a simple unmanaged switch connected between the ISP and the ASA's. I have two subnets with public addresses, for simplicity lets call them 1.1.1.0/24 and 2.2.2.0/24. Default routers are 1.1.1.1 and 2.2.2.1 respectively.
Can I somehow use both these subnets in the ASA's? Im currently using the first subnet and use PAT to direct traffic to internal servers. But if I want to use adresses from the second subnet wont that mess up the routing, since there is no way I can specify the default router for the second subnet? I have as of yet not tried anything, Im just trying to plan ahead and I cant seem to wrap my head around how this could possibly be done.
How do i tell my firewall to start listen also on another outside ipadress assigned by my ISP? I have it used on other firewall right now. So my steps would be shutting down ip address assignment off old firewall interface. Assign that ip address to ASA5510 outside interface and configure NAT.
View 13 Replies View RelatedWe have 2 firewall (ASA5510) pairs. Each pari configured for Active/Stdby mode.
Pair1 : Internet browising, Remote access VPN, Citirx access & L2L VPN access
For this pair , I need to move the 'outside' interface to Gig 1/3 and change the IP addresses. (minimize the downtime)[code] Remove the ip from outside interface and add the new IP and enable to monitor interface outside?
I have a Cisco ASA5505 and windows DHCP server, how do I add this external server to ASA so my PC clients can get DHCP from this server?
View 3 Replies View RelatedWe have a working config with 1 external IP, we need to a second webserver (https) and it should be routed via a second public IP address. I already tried some suggestions from the community but haven't been able to find the solutions.
xxx.xxx.xxx.194 is going to the internal IP of 192.168.60.1 for OWA (https)
xxx.xxx.xxx.195 should go to a new webserver on 192.168.60.3
both server should be connected using SSL This is the current configuration :
ASA Version 8.3(1) !hostname fwdomain-name domain.localnames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.60.250 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip address xxx.xxx.xxx.xxx 255.255.255.0 !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveclock timezone CEST 1clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00dns server-group DefaultDNSdomain-name domain.localobject network obj_any subnet 0.0.0.0 0.0.0.0object network NETWORK_OBJ_192.168.70.0_26 subnet 192.168.70.0 255.255.255.192
[code].....
I want to block the sql port access of my server to all except few of my ip addresses while access list on Cisco Router IOS how do i do that.
View 3 Replies View RelatedI've configured a 5505 but internal clients can't ping external ip. To test I've connect a pc with the ip of the default router on the Outside int the ASA can ping the PC and the PC can ping the ASA, but internal clients can't ping the PC
PC config 195.12.23.241/28
Here's the ASA config, so far I've wiped the ASA and started with a blank sonfig and built it up but still not working.
ASA Version 8.2(5)
!
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
[Code] .....
Does the ASA 5505 will allow the addition of a 2nd external link to its configuration? I know the device is capable of Redundant or Backup ISP Links, but that’s not what I need. I will have two different links for two different purposes. Currently we are using the ASA 5505 just for Internet access, so only the ISP link is connected, very basic configuration. We are planning a connection to a client’s global (MPLS) network and we need to be protected against any traffic coming from that network, ergo we need to use a firewall for connection to that external link.Now with the final configuration the Internet traffic must keep being routed to the ISP link, and some other traffic must be routed to the new external link. Can the ASA 5505 be configured for this scenario?
View 7 Replies View RelatedI'm looking to setup AnyConnect VPN with no split tunneling. ASA 5505 v8.2. It seems this should be really easy. I must be missing something.
I can get the AnyConnect users to connect fine and they can access sites internal and at other IPSec-tunneled sites. But no access to the internet.
Internal is 10.1.1.x, VPN pool is 10.1.1.251-253 (Temp list for testing). I issued the following tracer: packet-tracer input outside tcp 10.1.1.253 12345 69.147.125.65 80 detailed
The last reported point (where it fails) is:
Phase: 7
Type: WEBVPN-SVC
Subtype: in
[Code].....
I have a Cisco 5505, 2 sites that are internal, 1 external IP (dhcp from cable modem). While on my laptop, ipad, iphone, I cannot access the server via it's external IP address. I MUST use the internal IP in order to access this site. I have heard of hairpinning, internal dns server(don't really want this).
View 8 Replies View Related