I have a Cisco 5505, 2 sites that are internal, 1 external IP (dhcp from cable modem). While on my laptop, ipad, iphone, I cannot access the server via it's external IP address. I MUST use the internal IP in order to access this site. I have heard of hairpinning, internal dns server(don't really want this).
View 8 RepliesI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 5 Replies View RelatedWe have an ASA 5505 running version 8.4. We are having problems allowing external traffic to access computers behind the firewall. Our current config is:
ASA Version 8.4(3)!hostname ciscoasadomain-name default.domain.invalidnames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 10.2.1.1 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 152.18.75.132 255.255.255.240!boot system disk0:/asa843-k8.binftp mode passivedns server-group DefaultDNSdomain-name default.domain.invalidobject network a-152.18.75.133host 152.18.75.133object network a-10.2.1.2host 10.2.1.2object-group network ext-serversnetwork-object host 142.21.53.249network-object host 142.21.53.251network-object host 142.21.53.195object-group network ecomm_serversnetwork-object
[code]....
Our secondary site accesses the internal intranet via a link, which is basically:
[URL] where externalip is the IP address of my router.
* This used to work fine before we migrated from ADSL (6mb up / 0.5mb down) to Fibre(70mb / 20mb) *
Internally, I access the same link, but via [URL] Internally it loads in 2 seconds, externally it is taking 68seconds(ish)..
I can't work it out, the fibre shouldave made things loads quicker but is infact very slow. I'm wondering if something network wise is going on.
The intranet is a php intranet sitting on apache, and using postgresql as the database. Other pages load fine, this specific index.php page does quite a lot of DB connections and so on, but as I say before, it worked fine before the migration.
we recently upgraded from an RVS4000 router which didn't have this issue.
the problem; Internal users from Site A cannot access the external owa address.From Site A i can successfully ping both the external/internal IP addresses/names and they resolve correctly, including pinging the address ('mail.company.com") resolves correctly to the external ip address.
[code]...
I have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 7 Replies View RelatedI'm looking to setup AnyConnect VPN with no split tunneling. ASA 5505 v8.2. It seems this should be really easy. I must be missing something.
I can get the AnyConnect users to connect fine and they can access sites internal and at other IPSec-tunneled sites. But no access to the internet.
Internal is 10.1.1.x, VPN pool is 10.1.1.251-253 (Temp list for testing). I issued the following tracer: packet-tracer input outside tcp 10.1.1.253 12345 69.147.125.65 80 detailed
The last reported point (where it fails) is:
Phase: 7
Type: WEBVPN-SVC
Subtype: in
[Code].....
I have 3 external ips from my isp:
222.222.222.221
222.222.222.222
222.222.222.223
The first one I use to provide internet access to my office. The other two I'm going to use for the following: I'm going to deploy a server in internal network which must have 2 external ips on his network interface (& one internal ip on the second,but that's ok: I cannot put an extra network switch before asa & plug this server there: this server is virtual & is on esxi host in internal network. External ips must be assigned to servers' interfacw,bot just forwarded there (ms direct access requirement).
My current config:
!
ASA Version 8.4(3)
!
hostname msk-office
[Code]....
I found a link to accomplish this on the old code but how can I get this done on 8.4.
[URL]
I have Astaro UTM running on an old computer as my only firewall right now. The Astaro also serves as my DHCP server. My Wifi is provided by a Linksys E3000 running DD-WRT software. NAT/SPI are disabled on the E3000, and it forwards DHCP requests to the Astaro. All my network clients connect via wifi/ethernet to the E3000.
All clients --> E3000 (no firewall) --> Astaro --> www
I am considering setting up my own personal cloud server using a Synology NAS that I can access remotely. I would also like to remotely access my Surveillance DVR. I would like to access them via VPN or portforwarding. I do not want to use DMZ.
I would like to utilize the SPI firewall on the E3000 to provide an extra layer of defense. I would like the NAS and the DVR to be on an external LAN between the Astaro and the E3000...and all other clients being on an internal LAN behind the E3000. I have the necessary switches/cables to make this work.
My question is...How do I configure the E3000? Can I have both the internal and external LANs on the same subnet? Do I have to use the NAT on the E3000? I'd rather not...since that will render the Astaro's reporting functions rather worthless.
I would like the Astaro to remain the only DHCP server. I would like all internal LAN clients to be able to reach out to the external LAN/WAN...but the external LAN should not be able to reach into the Internal.
I am aware that we can allow external admins to telnet over a custom port to the internal router. Even i was allowed to connect to a remote router via the remote firewall. The way i was accessing the router is by telnet to the remote ASA address on port 8023.I am not sure how exactly we can configure this on a ASA.
View 2 Replies View RelatedI was just wondering if it's possible with an ASA 5510 to connect to the external IP address of an internal server from inside the network. I have already set up dns doctoring for dns lookups, and everything is working fine there. We have an application inside the network that tries to connect straight to the external Ip of another internal server. where to look in the ASDM 6.4?
View 2 Replies View RelatedI am using a 6500 with FWSM. I need to separate an internal server/HQ network from 3 or 4 different external connections. The external networks do not necessarily need to be isolated from each other.I have the option of using a 3 layer model: L2 Access layer to SVIs on the Distribution layer and then L3 to the 6500.L2 Access, connecting directly to the 6500s, with the SVIs on the FWSM.Is it better to have the FWSM outside the MSFC or Inside? Am i correct in thinking that "inside" vs "outside" is determined by whether the SVI's are configured on the FWSM or the MSFC? is there any performance impact from having the FWSM doing the routing instead of the MSFC.If the vlans are all configured on the FWSM, what is the 6500 doing, other than providing switch ports?
View 1 Replies View RelatedI am working on replacing our Checkpoint Firewalls with ASA's, and am running into the following NAT problem. On some of our Checkpoints, there are external NAT's that are mapped to multiple internal hosts based on ports.Is there any way to translate that to the ASA? I'm not sure the ASA will let you have multiple internal hosts mapped to one external IP using static NATs. The main issue, is these are alarm panels that receive data from external hosts (the traffic is initiated externally on the Internet) so I can't use dynamic PAT with this.
View 1 Replies View RelatedWe have an ASA-5505 running 8.2(1) with a Bosch DVR 600. When a machine is on the local subnet, it can see the video; however, when it's moved to the DMZ, the unit can be accessed, but all video screens are black and an java script error pops up as follows: [URL]
This message does not pop up when on the local subnet. Additionally, in the login screen, there is a language selection, and sometimes all languages are blanked out. There is a space for them, but they don't display.
I've tried this on a half a dozen machines, either XP or Win7 with IE8 and IE9, and they all do the same thing. I disabled http inspection, but that doesn't work. I also did a packet capture, and the only packets that traverse the ASA.
I want to access my ASA 5505 from internet.how I can achieve it.
View 1 Replies View RelatedFor some reason there are some sites that I cannot access websites from inside interface.One such example is lxer.com where I am receiving this message in the browser:The connection has timed out The server at www.lxer.com is taking too long to respond.This has "suddenly" happened, and so I am wondering what others have done when such things has happened. My outside has a dhcp-IP, and I have noticed that this address had changed, so I corrected this in my router settings.ASA version is 5505
These are my settings:
: Saved
:
ASA Version 8.4(2)
!
hostname ciscoasa
domain-name example.no
enable password 123412321 encrypted
passwd 1231231 encrypted
names
[code]....
I have a Cisco ASA5505 and windows DHCP server, how do I add this external server to ASA so my PC clients can get DHCP from this server?
View 3 Replies View RelatedWe have a working config with 1 external IP, we need to a second webserver (https) and it should be routed via a second public IP address. I already tried some suggestions from the community but haven't been able to find the solutions.
xxx.xxx.xxx.194 is going to the internal IP of 192.168.60.1 for OWA (https)
xxx.xxx.xxx.195 should go to a new webserver on 192.168.60.3
both server should be connected using SSL This is the current configuration :
ASA Version 8.3(1) !hostname fwdomain-name domain.localnames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.60.250 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip address xxx.xxx.xxx.xxx 255.255.255.0 !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveclock timezone CEST 1clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00dns server-group DefaultDNSdomain-name domain.localobject network obj_any subnet 0.0.0.0 0.0.0.0object network NETWORK_OBJ_192.168.70.0_26 subnet 192.168.70.0 255.255.255.192
[code].....
I have a Cisco ASA 5505 (version above) and I have someone that needs to SSH into a box behind the ASA. I'm having a few issues trying to configure this access-list and NAT. I've tried many combinations and clearly my IOS is not as good as I thought. What commands should I enter to accomplish mapping SSH from an outside network range to an internal host ?
View 5 Replies View RelatedI want to have my port 4 on the asa 5505 only allow access to the internet and not the internal network, what do i need to do?
View 1 Replies View RelatedI now need to configure an ASA 5505 for a small server farm. It's fairly straightforward:isp -> asa5505 -> internal servers,'m using static addresses -- no DHCP involved.VPN works; I can get into the internal network.pinging from the ASA to an external address works,However, I cannot get from a laptop connected to an internal port out to the internet, either using ping or typing an address in the browser.
View 7 Replies View RelatedI am new to Cisco ASA and have been configuring my new firewall but one thing have been bothering. I cannot get internal networks and routing between them to work as I would like to. Goal is to set four networks and control access with ACL:s between those.
1. Outside
2. DMZ
3. ServerNet1
4. Inside
ASA version is 9.1 and i have been reading on two different ways on handling IP routing with this. NAT Exempt and not configuring NAT at all and letting normal IP routing to handle internal networks. No matter how I configure, with or without NAT I cannot get access from inside network to DMZ or from ServerNet1 to DMZ. Strange thing is that I can access services from DMZ to Inside and ServerNet1 if access list allows it. For instance DNS server is on Inside network and DMZ works great using it. [code]
I am having some trouble accessing some backup Email (Outlook Web Access) and Citrix servers located behind an ASA 5505 firewall at a remote datacentre. Simply put, when I go to the specific URL (e.g. [URL]) I do not arrive at the splash page, I just get a message saying that the server took too long to respond in the web browser. I'm wondering whether I have missed something on the configuration or the firewall itself is not letting my requests through. The remote servers are located at a remote Disaster Recovery site and use the subnet 192.168.4.0/24. I am at head office which is connected to the DR site via a VPN using 192.168.1.0/24.
[Code] .....
I have a client in a workgroup environment. They are a small company with perhaps twenty systems. Their infrastructure consists of a Dell Switch, a Cisco ASA-5505 which hands out the DHCP and a router. And that's that.They have been using an external IP as their DNS Server to get out to the Web. However, they now want to add an internal Linux-based DNS server.In looking through the ASA-5505 today I noticed a field for DNS enteries. Is this where the IP for this new internal DNS Server (in the secondary DNS field) would go?If so, would it be necessary to reboot the ASA-5505 for this change to take effect?
View 12 Replies View RelatedWe recently changed locations and acquired a new circuit from our provider. They also connected our remote branch office to our main office through MPLS. Now, as I understand it, the branch office basically connects back to the main office through our providers network (MPLS). We have a new router at the branch office which has a gateway of 192.168.1.225. The clients in that office have IP's of 192.168.1.96 - 100, using the gateway of 192.168.1.225.
The main office network is 192.168.0.0 (Gateway of 192.168.0.1)
At this end (Main office), I also have a new Cisco 2900 provided by the ISP, with port 0/0 for the outside connection (connected to the 0 port on my ASA 5505). The ASA's port 1 obviously running into my network hub. The provider tells me that port 0/1 on the 2900 is or should be used to connect the branch office back to here and has an IP of 192.168.0.225, as that's how the provider provisioned it. So, I plug that into the ASA's Ethernet port 0/2. And I'm assuming they have a route setup either on the 2900 or the router in the branch office so that 192.168.1.225 can reach me here at 192.168.0.0.
There is already a static route setup on the ASA: (192.168.1.0 255.255.255.255 192.168.0.225 1). As soon as I plug in the cable, the IP phones at the branch office work, but they can't access the internet or any resources in the main office. My questions are:
1. Shouldn't I be able to just go straight from the 0/1 port on the Cisco 2900 to my hub. At first I was plugging right into the ASA, but I don't think I need to do that, why go from the branch office through my ASA to access resources and then back out the ASA for internet. If they're already coming from 192.168.1.225, through the MPLS network, then they should go right to my network and then back out the ASA.
2. They have to route through the ASA first, in which case, do I need to setup another VLAN for that branch network in conjunction with a static route? I can ping the router and hosts in the branch office through the ASA only!
Below is the running sanitized config:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(2) !hostname ciscoasadomain-name audiology.orgenable password ulzaQiFnKVzDwUmW encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.0.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 1.2.3.4 255.255.255.240 ospf cost 10!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!boot system disk0:/asa822-k8.binftp mode passiveclock timezone EST -5clock summer-time EDT recurringdns server-group DefaultDNSdomain-name audiology.orgsame-security-traffic permit inter-interfacesame-security-traffic permit intra-interfaceaccess-list
[code]....
I can not access Windows Live Messenger, it will not connect. I can visithotmail.com but not delete or send any e-mails. It says Hotmail is not responding.I can also not access Windows Update. When I search for updates it comes back with error 80072EE2. I also have problems accessing secure websites where I need to pay for something, e-Bay, paypal, make payments off Credit Cards etc.However I can access all websites on my iPhone over the same Wi-Fi. I took the same laptop to 2 other addresses and it works fine at both and able to access all webpages etc!I am running Windows 7 and have tried IE, Safari and Firefox, all with same problems. I am with o2 home broadband and have been with them for years with no problems. I have replaced the router, and have another new router on the way, but am expecting the same problems!
View 1 Replies View RelatedIn my office there is 2 desktops which is networked. one is in the office and the other in my room. internet connection is also there, the modem is kept in my room. but one of my cousin is there in my house and he has a laptop, the internet for his lap is taken from my modem. and now i have noticed that my cousin is visiting adult content sites and i want to block him ? is there any way. why the history he uses is being shown in my browsers history ?
View 13 Replies View RelatedI've configured a 5505 but internal clients can't ping external ip. To test I've connect a pc with the ip of the default router on the Outside int the ASA can ping the PC and the PC can ping the ASA, but internal clients can't ping the PC
PC config 195.12.23.241/28
Here's the ASA config, so far I've wiped the ASA and started with a blank sonfig and built it up but still not working.
ASA Version 8.2(5)
!
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
[Code] .....
Does the ASA 5505 will allow the addition of a 2nd external link to its configuration? I know the device is capable of Redundant or Backup ISP Links, but that’s not what I need. I will have two different links for two different purposes. Currently we are using the ASA 5505 just for Internet access, so only the ISP link is connected, very basic configuration. We are planning a connection to a client’s global (MPLS) network and we need to be protected against any traffic coming from that network, ergo we need to use a firewall for connection to that external link.Now with the final configuration the Internet traffic must keep being routed to the ISP link, and some other traffic must be routed to the new external link. Can the ASA 5505 be configured for this scenario?
View 7 Replies View RelatedI tried the solution posted at [URL] however it did not work on my ASA5505 8.4(2). I thought that it may be because I only have a single public address so the web server is responding to port forwarding through the one public IP already. looking in ASDM it appears to indicate that a configured access list is blocking the server from responding to the internal hosts.
object network Private_IP
host 192.168.1.15
object network Public_IP
host 1.1.1.1
object-group network internal_net
[code]....
Can I fix an access list (or something) to make this work or am I wishing for too much with only one public IP? This worked by default on my Netgear firewall.
I'm usually not working with this product, but this is what I'm trying to do.I have 2 internal networks setup on our Cisco ASA 5505 firewall. (not done by me, I'm a new to this product)I'm trying to access a server on one network from a PC located on the other internal network. (preferable through the web gui)When I try "Packet Tracer" from interface "Trust4" it fails on the NAT phase.(Source ip: 10.0.4.99, Destination ip: 10.0.6.99)
When I check the NAT rule, it says:
Type Source Interface AddressDynamic any outside outside.
Cisco ASA 5505 Cannot Ping Secondary Internal Network.
View 9 Replies View Related