Cisco Firewall :: Using ASDM To Change External IP Address Of 5505?
Mar 13, 2013
We have an ASA 5505 and are changing ISPs so we'll be getting a new static IP address. How do I change the external IP address using ASDM? (I haven't done it in 5 years so I'm rusty and just want ot make sure.) The ASA and ASDM are up to date.Am i correct in that I only need to change the external address in the configuration under Interfaces, then under Routing - Static Routes - Gateway IP I just need to enter the new WAN gateway address?
View 2 Replies
ADVERTISEMENT
Jul 8, 2012
I have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 7 Replies
View Related
May 30, 2013
I have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 5 Replies
View Related
May 4, 2011
I have a couple of ASA 5505's which work fine for what they are doing VPN and all that - we have 1 DLINK DFR-700 Firewall left and I need to get a new ASA to replace this since it is old.
All this box really does is port forward external clients to 1 address on the internal lan for client software updates. Any example configs?
So lets say we have client a with IP 1.1.1.1 and client b has 2.2.2.2 - at the moment this is what happens client a and b come in through http and get mapped to the internal http server 10.10.1.2
So I need to setup about 100 clients which can come in through http only - get mapped to the internal IP and also keeping the internal server to be able to access anything outside.
View 1 Replies
View Related
Nov 10, 2011
I have a cable modem internet connection and my cable modem is connected to an ASA 5505. The inside interface of the ASA has an IP address of 192.168.2.2 and is connected to a Linksys router's internet port which has an IP address of 192.168.2.1. The Linksys router then has a local area network of 192.168.1.0 and all my clients are on that network. Everything is working fine except in my ASA logs all the traffic shows up as the router's external address which is 192.168.2.1. I would like to see the 192.168.1.x address of the clients in the ASA firewall. I've tried making some changes to the Linksys router but that hasn't resolved it. Is there any changes I can make on the ASA to get this to work?
View 6 Replies
View Related
Sep 10, 2012
I'm configuring a 5505 for a remote office. Until they are assigned a static ip by the provider I will have to use the providers dhcp address. How do I construct an access list for the outside interface using the external address if I don't know it yet? is there a commnd that will insert the ip address in to the access list once one is assigned?
View 5 Replies
View Related
Sep 15, 2011
The problem is that the PABX is sending out an internal address in it's INVITE messages and the ASA5505 isn't changing the internal address to the external address.We need> From: Calling Number <SIP: SIP Username@Public IP Address>However our PABX sends out> From: Calling Number <SIP: SIP Username@Private IP Address>. How to translate the internal IP address to the external IP address on an ASA 5505?
View 1 Replies
View Related
Mar 30, 2011
How can I change my external IP address which is assigned
View 1 Replies
View Related
Oct 9, 2012
I have an ASA 5520 new. I am trying to migrate from a PIX 515E. I can connect via the CLI and ASDM on the management port (IP 192.168.1.1 the default) What I am having an issue with though is when I change the management port to 10.0.1.1 via the CLI or ASDM I can no longer use ASDM. I issue the show IP command in the CLI and I see that the IP has indeed changed but I still can not get into it. I must be missing something really simple, but this is driving me insane. I want to change the IP because I need the a different interface to be 192.168.1.1.
View 2 Replies
View Related
Sep 22, 2011
im working on a small project on a asa 5505 and beacuse i do most of the work from the outsidei want to open up asdm without vpn.
i have it working on another asa and the only difference is the rom version.the one not working is 8.0(5) - 6.2(3) and the one working is 8.0(4) - 6.1(5) did they do some changes?
View 6 Replies
View Related
Feb 28, 2013
I have been browsing the forum and the support notes for a couple of hours and haven't found a definitive answer to my question. Our ASA is on the subject versions. I watched a video on YouTube stating that upgrading the ASA is easiest if you upgrade ASDM, then the ASA. Problem is, I don't think I can upgrade ASDM first because I don't see a version that is compatible with ASA 7.2.x and 8.0.x.
View 3 Replies
View Related
Feb 19, 2012
I want to kown if is posible install IOS 8.3(2) and asdm 6.3(1) in firewall 5505 wich has 512MB of RAM and 128MB of flash. I installed it but according to the cisco page it can´t. maybe could work bad ?
View 1 Replies
View Related
Sep 14, 2011
I have a firewall Cisco ASA 5505, and currently it is a command line firewall. I want to configure ASDM so that i can use it as a GUI Web Base interface.I really don't know what to do. How can I configure ASDM on my firewall.
View 7 Replies
View Related
May 21, 2012
I have a standard ASA 5505 with inside, dmz and outside with the default security levels, 100/50/0. we have an email server inside which has been NATed and is working fine. However users accessing the wireless on the dmz are unable to access their emails on https (443). How do I allow SSL access ONLY to users on the dmz using ASA 8.4 commands or ADSM 6.4?
View 10 Replies
View Related
Oct 1, 2012
I am trying to configure a site to site ipsec vpn with 2 cisco 5505 ASA's. Unfortunately when i open up the ASDM there is no vpn wizard to start the configuration.The version of ASDM i am using from flash is 645-206.bin and the firmware on the ASA's is 842-k8.bin so should be ok. Why the VPN wizard doesnt appear?
View 7 Replies
View Related
Jan 3, 2010
recently, ater successfully connecting the VPN to the ASA 5505, I am unable to then launch the ASDM client meaning that I can only SSH in to the unit.
I found an old post from 2008 and replied. It refers to an article talking about it is not possible to enable https server and webvpn on the same interface.
Well I am running ASA 8.0(4) so this restriction does not apply.
View 16 Replies
View Related
Nov 16, 2011
I have successifuly upgraded ASA and ASDM image. My question is how to make it to boot it as default when you do a factory reset of the device. For the ASA image I found out that it will boot the first image it founds on the flash, so I left only the latest bin file and if I do factory reset it boot the latest. But for ASDM it still boots the old one, because there is no "asdm image disk0:/asdm-645.bin" command in the config. I`m not sure how, because I only left the new ASDM bin image. Is there any variable or something that still points to old asdm image?
My ASA version is 8.4(2) and ASDM 6.4(5). The old one was ASA 8.2 and ASDM 6.3.
View 2 Replies
View Related
Jul 22, 2012
I have Cisco ASDM 6.2 for ASA and I have been requested to add a list of URLs and IP address to the whitelist on the firewall.
I haven’t had much experience using this program so unsure of where I go to add these and I don’t want to risk changing anything that might affect the security of the firewall.
View 4 Replies
View Related
Jan 20, 2013
I've have an ASA 5505 with a inside network vlan1 (192.168.0.0/24) - i've configured an IPsec VPN profile and a VPN network of 192.168.0.50/24. I can through my VPN tunnel access inside hosts on vlan1 - but not ASDM on the ASA (192.168.0.1). Under management i've added the VPN network of 192.168.50.0/24 to have access to ASDM, but still does not work.
View 1 Replies
View Related
Apr 10, 2012
We have a new installation of a ASA 5505 and are trying to get some NAT issues straightened out. On our internal network, we have two servers running Filemaker Server, a relational database server that clients connect with using port 5003. Our goal is to be able to allow users from the outside to access either of these servers as needed. I know how to set up a simple static NAT rule and matching Access rule in ASDM which would be fine for a case in which only one server using a given port is running on a network, but for simple static rules I seem to be blocked from entering a different translated port number from the orginal port number, which becomes a problem when two servers we need to access from the outside are running software using the same port number.
What is the simplest way to address this need? I am guessing that I need to set up a scenario like this, where port 5004 (or any arbitrarily choosen unused port, can be used to access the second server: [code]
View 1 Replies
View Related
Jan 5, 2012
How do I enable remote access to ASDM from outside of the network on the ASA 5505? This would be used for remote access to the firewall at a site that is not utilizing VPN.
View 5 Replies
View Related
Jan 9, 2013
Remote LAN pool is configured as inside. Route is proper. I am able to open 443 port from the remote LAN pool on the ASA. That means, the port is open from the remote pool. No response if I try https on the browser.
View 11 Replies
View Related
Apr 30, 2013
I have a Cisco ASA 5505 V10. I've upgraded it to use asa825-K8 & asdm-649.103. Before the upgrade I was able to get to the ASDM via https://192.168.1.1. However after the upgrade I just get a page cannot be displayed. I have rebooted the ASA.
View 4 Replies
View Related
Oct 18, 2012
My macbook pro recently upgraded to the last version of java and now I can open the ASDM for my Cisco ASA 5505, when I try open, only show me the window of Java 7 ..., and don't load the ASDM.
View 15 Replies
View Related
Feb 3, 2011
Today I upgraded my Cisco ASA 5505 ASDM from version 6.34 to 6.41 cause of some problems on old version with NetFlow. But now when I switch to dashboard i can not see "Top Usage" tab. That was quite usefull for me. It simply disappeared.
Can i somehow configure which tabs are displayed on dashboard ? I really need that one and I do not want to downgrade :/
View 7 Replies
View Related
Jun 20, 2011
I am trying to open up 3 TCP ports in Cisco ASDM Launcher:
16000
16001
8098
And have a Cisco ASA 5505 Router. I need these ports open in order for a software that I have installed on the server to communicate with my local client computers for my business, The software is installed on Windows 2008 Server Standard Edition and was installed with MicrosoftSQL 2005. The software and Microsft SQL 2005 is pretty much installed and just requires this last step in order for the server to be connected to the local computers. In order to resolve this, I have gone to.
View 1 Replies
View Related
Feb 6, 2013
I have an ASA-5505 which I have been managing using ASDM from a PC and a Mac.I just happens that the Mac has not been used in a little while and when I tried to use ASDM on it, it fails.I've had a trawl through various posts and release notes (after updating various components in the process, incl Java with all the diabling/security updates of late) but am still having the problem and this is where I'm at:
- the ASA runs v8.4(2) and ASDM 7.1(1)52
- release notes state that ASDM 7.1 should work on Java 7 on Windows 7 and MacOS 10.7
- ASDM starts fine on my Windows 7 PC running Java 1.7.0_13
- I am also running Java 1.7.0_13 on MacOS 10.7.5
- on MacOS, ASDM starts, asks for credentials, download/refreshes the cached app... and then crashes with the following exception message:
The root cause of the issue seems to be that a Java class called apple.laf.AquaTableHeaderUI is not found..Now, I don't know much about Java, but that seems to be an Apple UI related class - I presume that it would be good to use this to give ASDM a more native look and feel, but why on earth is there no fallback? or am I missing something?
View 4 Replies
View Related
Jun 17, 2012
I've been trying to configure this Cisco ASA 5505 for days now. I used to be able to use the ASDM gui application, but i've since transitioned into using the CLI. Trying to go back to ASDM, it won't let me get back in, and when i try show asdm image, it says Device Manager image file not set. I have no CD for this device and I need that image file for the ASDM. How can I locate the file and install it on the router so I can use it?
View 2 Replies
View Related
Feb 23, 2013
I was checking out the config on my ASA and noticed a bunch of static routes configured when I did a show route. With the exception of two that I expect to be there, the remainder point traffic destined for specific internal hosts to the outside interface, i.e.
S private_ip 255.255.255.255 [1/0] via public_ip, outside
I verified that I cannot ping those hosts from the firewall. I logged in to the ASDM. When I check the Configuration>Device Setup>Routing>Static Routes it only shows two static routes, the ones I expect to see. If I look under Monitoring>Routing>Routes, I see the same output as I did on the CLI. I looked around to see if I was missing a key location for this information, and I was able to see the same static routes output in Monitoring>Routing>Routes. Since this is under monitoring though there's no way to delete these routes, and I still don't know where they were configured originally. Then I happened to check under Monitoring>VPN>VPN Statistics>Sessions, and I see several of the private IPs used in the static routes being used by VPN users, including my own! I know I didn't assign myself a static IP for VPN use or anything like that. So, what are these static IP routes? Why do I see them in the CLI and not under the Configuration tab? I mean, I know I can delete them from the CLI but I'm trying to figure out why the info is not synced. Am I seeing dynamically created content based on the VPN connections?
View 2 Replies
View Related
Oct 26, 2011
I am trying to use the apple finder/application to view all my apple mac-mini computers. I do have two asdm-5505 connected via a vpn tunnel.
At this point I can view only the computers on the local subnets. I called AppleCare and they gave some possible ports that can be opened in the firewall to allow the Bonjour protocol to pass through the ASDM:ports 5297/tcp, 5298/tcp-udp, 5353/udp, and 5354/tcp
View 1 Replies
View Related
Oct 27, 2011
I have a server that I need to open up some ports on to allow access to the new internal Sharepoint server we're setting up. I've been having some issues getting the ports open like once I put the commands in and save them that server suddenly stops allowing outbound traffic. After looking at a few things I noticed while I was looking at the config file that the ASDM location is showing 2 IP's, both are the same as the server I'm trying to open ports for one being the private IP and the other is the public IP I'm trying to use. Is this the reason I'm having problems when I try to open those ports to my server? Do I need to use both a different private and public IP for this server so I can get my ports to work? The programmers selected these IP's so if I need to change them I'll let them know in case they need to make changes for the Sharepoint setup. This is on an ASA 5505.
View 12 Replies
View Related
Jan 19, 2012
We have a number of 5505 ASAs at remote sites all of which are configured to connect to one of two head-end servers.We need to change the primary head-end IP addresses. At the moment devices are successfully connected to the secondary.If we issue vpnclient server i.j.k.l e.f.g.h then the device drops off the network and won't reconnect until it is power cycled.If we make the changes in ASDM using the GUI to remove the old primary and add in the new primary the ASDM says "No changes made".Devices are running 8.2 and 8.4 code and behaviour is the same.
how to change head-end server IP addresses without the device disconnecting and not coming back up? According to the configuration guide the ASA should cycle through the addresses every 8 seconds until it can connect - but it doesn't seem to do this as it won't connect to the good secondary head-end either!
View 1 Replies
View Related
Sep 6, 2012
I completed the PIX 515 to ASA 5505 migration today with no problems - ok one problem with the logon for ASDM. I'm trying no username and password - then using username and password from the 515 Pix with no success. How to reset the username and password for the ASDM GUI website.
View 3 Replies
View Related
