The problem is that the PABX is sending out an internal address in it's INVITE messages and the ASA5505 isn't changing the internal address to the external address.We need> From: Calling Number <SIP: SIP Username@Public IP Address>However our PABX sends out> From: Calling Number <SIP: SIP Username@Private IP Address>. How to translate the internal IP address to the external IP address on an ASA 5505?
View 1 Replies
I have an internal DVR system that I am trying to share to the outside world. We recently put in an ASA5505 and I am having trouble getting the settings correct.I want to use an external IP to access the DVR system from anywhere and have my ASA5505 redirect the traffic to the internal IP address. I assume I need to use a NAT and a route policy however can not figure out how it would be.
View 11 Replies View RelatedI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 7 Replies View RelatedI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 5 Replies View RelatedBasically I have a group of static public IPs and I need one of them to point to an internal server IP address. This is for the RVS4000 router.
View 3 Replies View RelatedHow to remotely changing ip address for my ASA5505.
View 1 Replies View RelatedHow can I change my external IP address which is assigned
View 1 Replies View RelatedWe have an ASA 5505 and are changing ISPs so we'll be getting a new static IP address. How do I change the external IP address using ASDM? (I haven't done it in 5 years so I'm rusty and just want ot make sure.) The ASA and ASDM are up to date.Am i correct in that I only need to change the external address in the configuration under Interfaces, then under Routing - Static Routes - Gateway IP I just need to enter the new WAN gateway address?
View 2 Replies View RelatedI found a link to accomplish this on the old code but how can I get this done on 8.4.
[URL]
I have a 2600 I am trying to setup for educational use.
My Cable ISP has issued me 5 routable IP's through their SMC modem 86.28.12.226-229. The SMC modem is .225. Currently the internal network can get out through .229 as expected but nothing outside (tcp 80 to web server) can get through. When I assigned the ip's to e0/1 as secondarr I could get it to route from the inside network (so hitting .226 80 went to the correct place) but it still didn't work from the outside - plus I read that wasn't a great way to do it anyway.
!
interface FastEthernet0/0
description LAN Interface
[Code].....
I have a checkpoint Safe@Office 500 firewall router, connected to adsl via another adsl device in bridged mode.We needed to assign an external IP to a device behind the firewall.We contacted the ISP, and now they have assigned an additional IP to our adsl account.I have read from the documentation that:"NAT can be defined automatically via the network object (Node, Network or Address Range). When you define NAT via the network object, rules are automatically added to the Address Translation Rule Base"....so I add the object, with the external IP given to us by our ISP, and the wizard simply complains that the IP address is invalid.My thoughts are that the router does not know about the additional IP provided by our ISP. If so, how do I tell the router that there are other IP addresses available to use? I have rebooted the router, and no luck.
View 1 Replies View Relatedi can can ping my host externally from another ip however i have left my house without port forwarding to my pc is there a way to connect to my pc via something like this command "xxxx.dyndns-home.com:192.168.1.100" i have tried this and does not work as it does not like the ":"truth be told my real goal is to ultimately be able to look at my webcam as it is pointed at a homebrewing project which i need to see. this is what i want to work on setting up while in rdp?
View 2 Replies View RelatedI am having an issue where occasionally the Sidewinder starts to see my internal RFC 1918 address instead of the configured external address of my firewall. This is for peering between the two. The error they see on the Sidewinder is:So instead of seeing the external peer address he sees a 10.220.3.18 address. We are not sure what triggers this becuase normally he see's my 63.117.98.222 address.
View 5 Replies View RelatedI am wondering if the folowing is a valid configuration:
WLC2504
AP2600
I need 3 SSID/VLAN, 1 for corporate devices, 1 for coporate smartphones, 1 for guest.
Port 1 on the 2504 should be used for management and corporate devices and connect to the corp network. Port 2 is for smartphones/guest and will be connected to a Cisco ASA 5515 that is connected to a second ISP.
Corp devices should get IP from an Windows DHCP. Smartphones/guest should get IP from the WLC. Is this possilbe? I read this in a document "To use the WLC as a dhcp, you need to enable DHCP proxy as it is required." Some how I am imagining that this will mess with the Windows DHCP. Is it better to use the ASA as DHCP for smartphones/guest?
I have 3 external ips from my isp:
222.222.222.221
222.222.222.222
222.222.222.223
The first one I use to provide internet access to my office. The other two I'm going to use for the following: I'm going to deploy a server in internal network which must have 2 external ips on his network interface (& one internal ip on the second,but that's ok: I cannot put an extra network switch before asa & plug this server there: this server is virtual & is on esxi host in internal network. External ips must be assigned to servers' interfacw,bot just forwarded there (ms direct access requirement).
My current config:
!
ASA Version 8.4(3)
!
hostname msk-office
[Code]....
Our secondary site accesses the internal intranet via a link, which is basically:
[URL] where externalip is the IP address of my router.
* This used to work fine before we migrated from ADSL (6mb up / 0.5mb down) to Fibre(70mb / 20mb) *
Internally, I access the same link, but via [URL] Internally it loads in 2 seconds, externally it is taking 68seconds(ish)..
I can't work it out, the fibre shouldave made things loads quicker but is infact very slow. I'm wondering if something network wise is going on.
The intranet is a php intranet sitting on apache, and using postgresql as the database. Other pages load fine, this specific index.php page does quite a lot of DB connections and so on, but as I say before, it worked fine before the migration.
I can hear nothing sound driver disabled... windows explorer wont open...and my notepad and calculator wont work either... how do i remove it..
View 1 Replies View RelatedWe have an internal DNS server that all internal hosts do lookups to .. these requests are forwarded onto open dns for anything the dns server isnt authoritative for.. My question is we have purchased the botnet filter and this requires the asa5505 dns client to be active on at least one interface .. Should i point the asa dns to an external IP such as 8.8.8.8 and apply DNS enabled on interface outside ( am using asdm) I don't want the ASA to control DNS for our internal clients we already have a internal server for this, i DO want the asa5505 to check dns packets against its botnet filter, whilst still using open dns for forwarding.
View 1 Replies View RelatedI have configured a Cisco ASA 5505 to allow VPN access from outside to my LAN using Cisco VPN Client software. The connection is establishing properly with the ip address from my VPNPool. From outside (on VPN connection) I can ping the interface e0/0 (outside) and the interface e0/1 (inside) of the firewall, but I cannot ping the layer 3 switch interface to which the ASA is connected ( int gi1/0/22 ip address 192.168.1.2/30 ) and I cannot ping any vlan interfaces inside my switch. Therefore, I cannot connect to any server on my internal LAN. I am available at any time if further information is needed. find attached my ASA config.
View 7 Replies View RelatedI have a hosted web server that has a website on it that needs to connect back to a database within our internal network. We have a Cisco WRVS4400N Wireless Router with 2 VLANS. VLAN 1 goes to a Watchguard Firebox which is connected to our internal network. VLAN 2 goues to our classroom network.
Our database is on VLAN 1. I have opened port 1433 on the Watchguard to allow SQL traffic from our Web Server. I can telnet from my workstation on VLAN 1 to the Web Server over port 1433, so I know the Web Server is not blocking anything. When I try to telnet from the Web Server to our Public IP address over port 1433, it fails.
I believe I have the firewall on the Cisco WRVS4400N off, so it shouldn't be blocking any traffic, but for the life of me I can't get this to work. I have been working on this for two days, and I NEED it to work. This was working up until last week, then it quit working. I am the only person making changes to our network, and there were no changes made during that time.
I have a Cisco 5505, 2 sites that are internal, 1 external IP (dhcp from cable modem). While on my laptop, ipad, iphone, I cannot access the server via it's external IP address. I MUST use the internal IP in order to access this site. I have heard of hairpinning, internal dns server(don't really want this).
View 8 Replies View RelatedI am aware that we can allow external admins to telnet over a custom port to the internal router. Even i was allowed to connect to a remote router via the remote firewall. The way i was accessing the router is by telnet to the remote ASA address on port 8023.I am not sure how exactly we can configure this on a ASA.
View 2 Replies View RelatedI was just wondering if it's possible with an ASA 5510 to connect to the external IP address of an internal server from inside the network. I have already set up dns doctoring for dns lookups, and everything is working fine there. We have an application inside the network that tries to connect straight to the external Ip of another internal server. where to look in the ASDM 6.4?
View 2 Replies View RelatedI am having an issue with internal and external clients. When we have the nat ip configured on the controller we cannot connect internal ap's at all. When we take the nat ip out it works fine. We are on code 7.0.220. I have tried the following command <config network ap-discovery nat-ip-only disable> and it did nothing.
View 1 Replies View RelatedI have set up a remote access ipsec vpn on an asa 5520. I can connect, and ping internal ip addresses, however I cannot ping back out to the internet, nor can the internal network ping the vpn clients and dns resolution internal or external does not work. I am seeing nothing blocked in the logs on the asa.
View 3 Replies View RelatedI am converting from a Cisco Model 850 to a RV042, all is well so far but I cannot implement one feature I had on the old router.I want to do one to one nat from one internal ip to one external ip but I only want to use one tcp/ip port.The command to do this on the old cisco 850 was this:"ip nat inside source static tcp 192.168.1.181 80 75.xxx.xxx.181 80 extendable"Can this be done with the RV042?I can do one to one nat but it include all ports.
View 1 Replies View RelatedI have Astaro UTM running on an old computer as my only firewall right now. The Astaro also serves as my DHCP server. My Wifi is provided by a Linksys E3000 running DD-WRT software. NAT/SPI are disabled on the E3000, and it forwards DHCP requests to the Astaro. All my network clients connect via wifi/ethernet to the E3000.
All clients --> E3000 (no firewall) --> Astaro --> www
I am considering setting up my own personal cloud server using a Synology NAS that I can access remotely. I would also like to remotely access my Surveillance DVR. I would like to access them via VPN or portforwarding. I do not want to use DMZ.
I would like to utilize the SPI firewall on the E3000 to provide an extra layer of defense. I would like the NAS and the DVR to be on an external LAN between the Astaro and the E3000...and all other clients being on an internal LAN behind the E3000. I have the necessary switches/cables to make this work.
My question is...How do I configure the E3000? Can I have both the internal and external LANs on the same subnet? Do I have to use the NAT on the E3000? I'd rather not...since that will render the Astaro's reporting functions rather worthless.
I would like the Astaro to remain the only DHCP server. I would like all internal LAN clients to be able to reach out to the external LAN/WAN...but the external LAN should not be able to reach into the Internal.
I would hereby like to inform if it is possible to configure the Cisco ASA5505 firewall to route internet via an external VPN, while a laptop and smartphone connect to the firewall via Cisco AnyConnect VPN.
The configuration would result into: Laptop on public internet -> Cisco ASA5505 VPN -> External VPN (Unix server) -> internet.
I have a cisco ASA5505, it runs a wide site to site VPN network and has 4 servers connected to it
10.50.15.4 > fileserver
10.50.15.5 > domain controller (exchange)
10.50.15.6 > terminal server
10.50.15.7 > terminal server
Now yesterday i removed 10.50.15.6 and replaced it with a new terminal server with the same ip address, ever since the ASA is blocking traffic between it and the domain controller (example)
2Oct 27 201214:51:0510600710.50.15.655978DNSDeny inbound UDP from 10.50.15.6/55978 to 10.50.15.5/53 due to DNS Query What has me baffled is the only thing different between today and yesterday is the new server is windows server 2008 and the old one was windows server 2003. The new server has the same LAN ip address as the old one to make the changeover seamless for the users.
why all the sudden my ASA has decided to block the traffic between those machines? all the other machines can talk to it fine just not the domain controller, and seeing that this is a terminal server naturally you can see the problem i face!
this router has worked flawlessly for 2 years now without any config changes and i cant work out why its blocking traffic between those 2 machines.
I have just purchased an ASA 5505 for my remote users to access our internal network. I have followed all the setup instructions I can find. I am able to establish a VPN connection using the Anyconnect client and can see some of my internal network. (Basically, only the subnet of the internal interface) However, I have several subnets inside my LAN which are routed by another switch inside my LAN. I have built in the correct static routes so that the ASA will send traffic to that intenal routing switch for any subnets not part of it's inside interface subnet. I can see and ping those subnets from the ASA itself but the AnyConnect clients cannot.
View 9 Replies View Relatedwe have a cisco ASA5505 with base license and 3 interface configured. Internal 192.168.1.1/24 DMZ 172.16.0.1/24 Outside 20.20.20.20/24 The DMZ is configured to allow the traffic pass to the outside interface only (base license allow only traffic to one interface) in order to let clients on this network to browse internet. On the outside interface there's a nat configuration that let the port 443 to be natted to an in internal server. Is it possible to let the clients in DMZ to access to the internal server on port 443 from the outside interface?
View 3 Replies View RelatedI have a 2800 with one Gigabit interface connection to our Lan and the other interface connected to the internet with a public IP address. Now I'd like to setup the router to resolve both internal and external DNS requests. Thus requests like www.google.co.za and LocalLanPcName should be resolved to their public and private IP's respectively. [code] When I ping any name the only DNS server that is ever queried is 192.168.1.200 (it does resolve internal name correctly though).
None of the other servers are attempted to resolve the name. It does not matter if I specify a FQDN or not.
How do I setup the router so that my internal resolution is handled by 192.168.1.200 and .201, while external resolution is handled by 41.160.36 and .37. Or alternatively, how do I configure it to at least try all 4 specified name-servers for resolution, and not fail after trying the first one unsuccessfully.
6509-E compact flash Internal vs External
View 1 Replies View Related
