Cisco WAN :: Configuring SSH On ASR1002 / Apply To Management Interface?
Jun 30, 2010How to configure SSH on a ASR 1002 and apply it to the Management Interface?
View 3 Replies
ADVERTISEMENT
Cisco Firewall :: 5520 - Configuring ASA Management On Sub-interface
Jul 27, 2010I have two ASA 5520 with 4 Giga interfaces and 1 management interface.
I need to use 4 interfaces four data traffic
1- Inside
2- Outside
3- dmz-1
4- dmz-2
The remaining will be the management interface only.How can I configure the Statefull failover and Management?
1- I used the management0/0 for The stateful failover.
2- I used gig 0 for outside
3- I used gig 1 for inside
4- I used gig 2 for dmz-1
5- I divided the gig 3 to two sub interfaces
a- gig0/3.1 for dmz-2
b- gig0/3.2 for Management and I defined it as a management-only
Cisco Firewall :: ASA 5550 - Configuring Sub-interfaces On Management Interface
Nov 29, 2011I am currently doing some research (for my employer) into creating multi-context sub-interfaces on a Transparent ASA 5550.
I have not been able to find any details on this subject which state it is or it is not possible. This will be used for Syslog logging.
Cisco WAN :: Management And BITS Ports On ASR1002
Aug 30, 2011We recently purchased a Cisco ASR1002 router with four on-board Gigabit SFP-style Ethernet ports. However, when I do a "show ip interface brief", I see that there's an extra Gigabit Ethernet port. See the last interface in the following output:
ASR_1002_router#sh ip int b
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 unassigned YES manual down down
[Code].....
On the router itself, in addition to the four Ethernet SFP ports, there are four additional RJ-45 ports. They're labeled "BITS", "MGMT", "CON", and "AUX". I know what the Con and Aux ports are, but what are the Bits and Mgmt ports? And is one of them the Gigabit Ethernet interface that I see listed at the bottom of the output? And if it is, is there anything special about it, or is it just another routed Ethernet port? Can I do something special with it, like out-of-line managment?
Cisco WAN :: Management Port In ROMmon Mode - ASR1002
Jun 4, 2013Is it possible to use the mgmt port when in rommon mode? I use the Mgmt port when IOS is loaded and it works fine. I reboot the router, issue a break to put it in rommon and have set some variables but my Mgmt port never has link and I cannot ping it from the network. In rommon mode it looks like this:
PS1=rommon ! >
MCP_STARTUP_TRACEFLAGS=00000000:00000000
BOOT=bootflash:asr1000rp1-adventerprisek9.03.07.03.S.152-4.S3.bin,1;
IP_ADDRESS=10.71.50.101
IP_SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=10.71.50.3
BSI=0
RANDOM_NUM=1133006948
RET_2_RTS=13:38:27 EDT Wed Jun 5 2013
RET_2_RCALTS=1370453907
?=0
Cisco WAN :: Configuring IP Accounting On ASR1002?
Oct 23, 2011what command is required to configure ip accounting on an interface?
I would have thought to what is required is on the interface, turn on Ip accounting i.e.
int gi0/0/0
ip accounting
However, there is no ip accounting command within the interface. We are running version Version 15.1(1)S2.
Cisco WAN :: Apply QoS LLQ To 1721 ADSL Interface
Apr 17, 2007I can not apply the LLQ to ADSL ATM interface. the system take the command with out any error message, but no in the show running config. Any Cisco link can explain this? [code]
View 2 Replies View RelatedCisco WAN :: ASR1002 How To Attach L2 Interface
Mar 11, 2012We have an ASR1002 with asr1000rp1-adventerprisek9.03.05.01.S.152-1.S1.bin software.I couldn't find any documentation on how to attach an L2 interface, in my case a subinterface with a single dot1q vlan, to a BDI interface.I'm able to create a bridge-domain interface but it's down down.The command bridge-domain on the subinterface url...
View 2 Replies View RelatedCisco Switching/Routing :: ASA5520 - Commands To Apply NAT On Interface?
Feb 15, 2012configuration of NAT on an ASA 5520. On the ASA I have 1 x WAN connection and 1 x Internet Connection as well as the Inside and DMZ. I want to translate traffic from certain subnets on the inside (say 10.1.2.0 255.255.255.0) to an outside address (say 1.2.3.0 255.255.255.0). I'm assuming the ASA using the number after the brackets to distinguish what to translate? So if I had another entry with a '2' after the brackets, any of the '1' entries wouldn't translate to this? I have access-lits inbound on the INSIDE interface, I'm assuming these are applied before any NAT and only items allowed through the access-list are allowed to NAT?
I also have an address I would like to statically NAT with a certain port number, how do I do this? After I've configured this, what are the commands to apply NAT on the interface?
Cisco WAN :: Cannot Apply Policy Route-map To VLAN Interface 3560G
May 1, 2013I have a 3560G that I cannot apply a policy route-map to one of the VLAN interfaces. I am running up to date software, c3560-ipservicesk9-mz.150-2.SE2 and it accepts the command, but does not show it in the sh run of the interface. I updated to this code as I had seen previously someone said it needed to be version 15 before you could apply route-maps to VLAN interfaces.
View 4 Replies View RelatedCisco WAN :: ASR1002 / Loopback Interface Will Be Accessible From Internet
Apr 16, 2013I have a router asr1002 and I need that my loopback interface will be accessible from internet ISP adderss space I have
46.xx.x.64 255.255.255.192
interface TenGigabitEthernet0/2/0.301
description -=ISP=-
encapsulation dot1Q 301
ip address 46.xx.x.66 255.255.255.248
[code]...
packets transmitted 9received 0packet loss 100 %time 8063 ms
Cisco Switches :: SG200 Apply The Smart Port Macro To Interface
May 23, 2012I´m a IOS CLI fanatic. Its the first tiem that I have to configure a SB switch. Its very confusing, I want setup a voice vlan id as 200. but I don see that this value change when I try to apply the smartport macro to the interface.Its possible change a smartport macro?
View 1 Replies View RelatedCisco Switching/Routing :: 3560 / Apply Acl Restrictions To The Vlan Interface Ip Address Itself
Nov 1, 2011I've set up my 3560 to do routing. Now, I'm looking for a way to apply acl restrictions to the vlan interface ip address itself.
View 1 Replies View RelatedCisco WAN :: ASR1002 - Show Policy Map Interface With Nested Class-Maps
Jul 18, 2011I have a requirement to provide stats on a per-department, per-destination basis between sites. If I take Voice as an example I have 5 child classes referring to the 5 departments each matching EF and a particular access-list that matches the department's subnet. I tie these 5 child classes into a parent Voice class-map.
Now when I issue a "show policy-map interface" command I see stats for the parent class-map only whereas I would expect to see a breakdown for each of the child classes which is what is required.
I am doing this on an ASR1002 running 3.2.2.
Cisco Switching/Routing :: Configuring Management Of SVI / Nexus 5548?
Aug 15, 2012I want to configure management for some Nexus 5548's?I wanted to manage the switches via an SVI. I have read the following document which gives details about the Management SVI but doesn't answer all questions.[URL]I am not running any layer 3 functionality on the switch, no layer3 license (which it mentions in the above link) Will I still be able to create a management SVI. I know I will need to enable the feature 'interface-vlan' to setup a Management SVI, does that require a license?
View 6 Replies View RelatedCisco Routers :: RV042 After Configuring DMZ / Remote Management Stopped Working
Sep 30, 2012I have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:
- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.
Cisco :: ASR1002 SNMP Statistics For GRE Tunnel Interface Statistics
Mar 28, 2013We use Cacti to get interfaces statistics of a ASR1002 router (version 03.04.02.S.151-3.S2).A new GRE tunnel has been created, but unfortunately we are not able to get basic interface average during the day.What is surprising is the fact the graphs are built on the night only.
It seems as soon as we exceed some level of Bandwidth (~ 700-800k) the tool does not get the information.The OID I try to get are ifHCInOctets (.1.3.6.1.2.1.31.1.1.1.6) and ifHCOutOctets (.1.3.6.1.2.1.31.1.1.1.10) and some other interface statistics for both 64 and 32 bits. [code]
Cisco :: Separate Interface For Management On ASA
Nov 5, 2012I'm trying to separate my management traffic from regular traffic by splitting the management and "outside" interface to separate vlans but I'm hitting a routing issue. Say I have have a management network of 192.168.1.0 255.255.255.0 running across vlan 1 and I want to use 192.168.2.0 255.255.255.0 running across vlan 2 for the outside interface to send all the other traffic excluding the management traffic across. Tag both vlans on the external interface, say Eth0/0 Default route of route outside 0.0.0.0 0.0.0.0 192.168.2.1, With this, you can not hit the management interface because there is no route defined for the 192.168.1.0 network. However of course if you try to set one, you'll get the "connected route exists" error. How can I set the default route or gateway of the 192.168.1.0 network on the ASA. Switches just don't complain like the ASA does.
View 8 Replies View RelatedCisco :: 6509 Sup-2T Management Through CMP Interface
Dec 3, 2012 We acquired recentlty a new Cisco 6509 with Sup-2T supervisor card
My question is the following : we have a management subnet on a Copper-based switch; we manage all equipments through this network. I planned to configure the management interface on the 6509 to connect this switch & monitor the VSS through it However, since it is a CMP interface, most of the actions (SNMP, IOS upgrade.. won't be possible through this link) Moreover, I don't think LMS would be able to get the configuration through it (except by configuring a script running "attach" command & show run
Is there something I miss or must I add another interface of the Catalyst to this network (the problem being that I have no copper line card)
Cisco WAN :: SRP 527W Web Management Interface Inaccessible
Jan 27, 2011We have recently purchased a Cisco Small Business Pro SRP 527W router, all seems good and it is running smoothly, no disconnections or sync issues like our last router. However, after a certain amount of time the web management interface is unavailable through the browser (accessing it via 192.168.1.254 or the alternative we set-up 1.1.1.1) It is totally unavailable and timeouts in the browser yet there is still internet access and network is still alive. The web management interface was accessible before though and the only solution I have been able to do to access it again is to reboot this router.Could it be possible that because port 80 is forwarded to a different IP it interferes with the Web management interface? And how wcould the interface port access be changed?
View 2 Replies View RelatedCisco :: WLC 2006 - AP Connecting To Management Interface?
Jun 7, 2011I have running a Wireless LAN Controller Cisco 2006.Today my management IP its public with Internet access. I am thinking in use a private IP without internet access. I have certains Access-Points in other building, that connect to AP Manager interface using Internet . When i see the tcp connections, i look that the access-point not only have TCP connections to AP Manager interfaces, it have TCP connections to Management interface too!!!.If i shutdown the connection between Management interface and Access-Points (mantaining the connection between Access-Point and AP Manager interfaces)?
View 1 Replies View RelatedCisco Application :: ACE 4710 - Management Only Interface?
Apr 25, 2012Am trying to replicate the managment interface functionality of a CSS on ACE 4710 but have problem with it being treated as a general routed interface.
Scenario
On ACE 4710 I have a front-end interface for client facing VIPS and a back-end interface facing a server farm, taking care of load balancing flows
Non load-balance system traffic for the back-end servers also flows through these two ACE interfaces, following a default route path (the back-ends use the ACE as default gateway) i.e. dns requests from the servers flow through the ACE egressing the front-end interface to hit a firewall and route to an internal dns server.
Issue
If I add a "management interface" to the ACE 4710 and give it an IP address for management access, the interface by default assumes 'routed' mode and as the ACE treats this as a general interface it will route traffic out of it. For example if the IP address of this management interface is on the same network as the internal dns server, it breaks that connectivity. This as the ACE will see the "management" interface as best route to directly connected network and send traffic to dns server over that, however dns server response traffic will follow its defult route path via firewall and ACE front-end interface to get reply to back-end server. The firewall will block this traffic as traffic is asymmetrically routed and firewall not seen the initial dns request packet.
Question
Is there a way of making an ACE interface a 'non routed' management only interface for out of band management use? That is ACE will not attempt to route general traffic through the interface
I realise I could achieve this with multiple contexts but want to have a single context for various reasons - i.e. to have a kind of like for like CSS replacement using ACE 4710
Cisco Firewall :: ASA 5510 - Management Interface
Feb 13, 2012I am having issues with the ASA 5510 management interface. I can't communicate with this interface. It is showing DOWN/DWON even if I type NO SHUT several times.
My existing config is as follows
our-asa-01# sh run
Saved
ASA Version 7.2(5)
hostname our-asa-01
names
dns-guard
interface Ethernet0/0
[code]....
Cisco :: 2028 WLC Management Interface / Unexpected Traffic
Apr 16, 2012I have a number of WLCs/WiSM2 running 7.0.230.0 (still using WCS for management). The management interfaces for the controllers are on a purely private subnet. While going through the intenet edge ASA logs I noticed some traffic drops for the controllers on the Inside interface. I took a packet capture from the controllers and found that they were sending TCP traffic to a number of IP addresses (Microsoft, Hotmail and Google) - always with a src port 2028 (submitserver) with the ACK/FIN flags set. Why this traffic is coming from the management interfaces? The management interface is not used by any wireless clients and is not the default interface for any of the SSIDs.
View 4 Replies View RelatedCisco :: WLC Management Interface Unexpected Traffic 2028
May 22, 2013I have a number of WLCs/WiSM2 running 7.0.230.0 (still using WCS for management). The management interfaces for the controllers are on a purely private subnet. While going through the intenet edge ASA logs I noticed some traffic drops for the controllers on the Inside interface. I took a packet capture from the controllers and found that they were sending TCP traffic to a number of IP addresses (Microsoft, Hotmail and Google) - always with a src port 2028 (submitserver) with the ACK/FIN flags set.
View 2 Replies View RelatedCisco Wireless :: WLC 5508 Management Interface Connection
Aug 1, 2010I'm setting up a new 5508. I've used the config from a 4402, have successfully connected to the Service port to manage the device, but for some reason cannot connect to the Management interface. In this case, port 1.
The service port is connected to a Catalyst switch and grabbed an ip address (10.2.x.x subnet) no problem. I can access the 5508 via https using the SP. However, port 1 is connected to the same Catalyst switch, but on a different vlan (subnet 10.20.x.x). Both ends show that the interfaces are up, I can ping the interface from any other host on the network, but when I try to manage the device via https I cannot connect. We are using WCS and I cannot add the device from the WCS. About all I can do is ping that interface.
Cisco Firewall :: ASA5512-X Setup Using Management Interface
Jun 28, 2012I have a brand new ASA5512-X running 8.6.1, and am trying to do an initial setup using the Quick Start Guide that came with it. However, the Management Interface is not working. I have a PC connected and set to use DHCP, but the port is not active. I connected a console cable and can see in the config that the interface is shutdown. So I set it to active, and the port is now active, but is not giving out a DHCP address as the guide says it should.I would like to use the ASDM Startup Wizard to configure this device, so how do I get it to work the way the instructions say it should?
View 2 Replies View RelatedCisco Firewall :: ASA5540 Management Interface IP Addressing?
May 9, 2011How does one allow /31 mask for an management interface on an ASA5540 using version 8.3(1)?
I need to configure a 192.168.x.y /31 on the management 0/0 interface of a ASA5540 and it is providing me with the following error:ERROR: /31 mask is not allowed
Cisco :: 1130AG - Block Management Interface Webpage
Mar 29, 2012I'm working on creating an open wireless scheme and we are simply going to use WPA with a key. What I'm getting a little stuck on is preventing access, by the guests that will connect to the WAPs, to the gateway/management webpage. I've been looking into seperating with VLANs and trunks (internal with management access and external for guests) but having a hard time with the configuration scheme.
Not sure if there is an easy way to just block that in the config or what.
Cisco Switches :: Accessing SG300-28P Via Management Interface?
Dec 21, 2012I have a new SG300-28P, and have had occasional issues with being unable to connect to it via anything other than the serial port. I have connectivity between my machine and the switch (tested with ping each way), and in fact, have the same problem if I take a laptop to the switch and connect them directly.What happens is that though the switch is operating normally, http, https, ssh and telnet attempts to access all fail in one way or another. Ssh and telnet either yields no response or a refused connection (even though those services are enabled). For http and https, I'll occasionally get enough of the web page to be able to tell what it is ... but attempts to log in just don't work.While this is happening, the CPU and packet load on the switch is very, very low.Rebooting didn't work entirely, though it may have made it better. Resetting to factory defaults and then reconfiguring makes it work.This is using the latest firmware: 1.2.7.76.
View 3 Replies View RelatedCisco Wireless :: WLC 5508 7.3 Management Interface Access To GUI?
Jan 16, 2013After I've upgraded software to the v7.3 and applied AP-SSO it made imposible to access the controller's gui via Service-port. So we tried to access it by management-port, but there is some problem too. It is not working from another subnets. But default gateway on management vlan is set correctly and I even tried to turn of all acl's on switch. WLC is only accessible from the same network. But at the same time wlc is replying on ping fine.All other protocols cannot connect to the controller.
View 3 Replies View RelatedCisco Firewall :: Management Interface In Cluster ASA 5515x?
Jan 6, 2013I have a misanderstand about management interface configuration in cluster. So I have a cluster asa 5515X with management interface. i Would like to be able to connect to any of the member of my cluster on management interface, so i would like to fix a different ip on management interface on each of my node ip 92 and 91. I think it is the only way to make asa firmware update to access local flash on each node.
my config
interface GigabitEthernet0/1
channel-group 1 mode active
no nameif
[Code].....
Cisco WAN :: 7200VXR - NPE-G2 Fast-Ethernet Management Interface?
Apr 30, 2012Is there a keyword that we use under the interface to specify that it is purely management?
We need to assure that the subnet and any node on that subnet is not shared with the default routing table.
how do we set the gateway for the management interface if the node we are sourcing the ssh session from is on a different private subnet?