Cisco WAN :: Management Port In ROMmon Mode - ASR1002
Jun 4, 2013
Is it possible to use the mgmt port when in rommon mode? I use the Mgmt port when IOS is loaded and it works fine. I reboot the router, issue a break to put it in rommon and have set some variables but my Mgmt port never has link and I cannot ping it from the network. In rommon mode it looks like this:
PS1=rommon ! >
MCP_STARTUP_TRACEFLAGS=00000000:00000000
BOOT=bootflash:asr1000rp1-adventerprisek9.03.07.03.S.152-4.S3.bin,1;
IP_ADDRESS=10.71.50.101
IP_SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=10.71.50.3
BSI=0
RANDOM_NUM=1133006948
RET_2_RTS=13:38:27 EDT Wed Jun 5 2013
RET_2_RCALTS=1370453907
?=0
View 3 Replies
ADVERTISEMENT
Jun 19, 2012
I'm trying to get an IP_ADDR set on the management port in SWITCH: mode but for some reason the port seems disabled. PC shows connection unplugged. MGMT_INIT is not a valid command (not listed under '?' ). Bootloader version is 12.2(53R)SE2 FC1.
View 4 Replies
View Related
Aug 30, 2011
We recently purchased a Cisco ASR1002 router with four on-board Gigabit SFP-style Ethernet ports. However, when I do a "show ip interface brief", I see that there's an extra Gigabit Ethernet port. See the last interface in the following output:
ASR_1002_router#sh ip int b
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 unassigned YES manual down down
[Code].....
On the router itself, in addition to the four Ethernet SFP ports, there are four additional RJ-45 ports. They're labeled "BITS", "MGMT", "CON", and "AUX". I know what the Con and Aux ports are, but what are the Bits and Mgmt ports? And is one of them the Gigabit Ethernet interface that I see listed at the bottom of the output? And if it is, is there anything special about it, or is it just another routed Ethernet port? Can I do something special with it, like out-of-line managment?
View 1 Replies
View Related
Jun 30, 2010
How to configure SSH on a ASR 1002 and apply it to the Management Interface?
View 3 Replies
View Related
Jun 9, 2011
loading a new bin file onto a Cisco wirless access point ,the access point i have found is only in rommon stage
Access point model is : ap1231g-e-k9.
View 4 Replies
View Related
Mar 19, 2011
On new 1841 Testing Router, I deleted the flash & did the reload. After reloading, instantly I entered into the Rommon mode. I have a backup of the flash in my TFTP Server, which is connected to the 1841 Router. how can I restore my flash file into my 1841 Router. I can not get myself out of Rommon mode. I also now even can not ping the TFTP Server as well. Do I have to configure in the Rommon mode ?
how to restore the flash image via TFTP Server on my 1841 Router.
View 7 Replies
View Related
Apr 4, 2012
I upgrade to a Flash 32mbs memory stick, as I reboot the 2600 Cisco router, it appear in the ROMMON mode, nonetheless, I followed some wrong procedure by changing components on the ROMMON command line. however now the router reboot or start with symbol only V2V2v2a, and I can no longer enter the ROMMON Mode or key anything in. I have a copy of the IOS on my TFTP server.
[Code]....
View 3 Replies
View Related
Jul 5, 2011
how to straight away enter priv EXEC mode when authenticated for asr1002?? Using XR12000, it can be done but asr1002 have to input enable passwd...my username for asr1002 have privilege 15 and i want to enter priv EXEC mode straight away after login without asking the enable passwd.
View 4 Replies
View Related
Dec 10, 2011
I'm currently pursuing to take my CCNA and am currently studying for it, but have recently encountered a problem with one of my 1760 routers that I can not solve.Yesterday I went to boot up my router like normal, however when I went into hyperterminal I noticed the router was in Rommon mode. Thinking I could change the configuration registry, I tried to bypass the NVRAM by using confreg 0x2142. However this still causes the router to go into Rommon mode. I am getting an error that states that there is insufficient memory to load the IOS image. [code]
I have used the dir flash: command and can see the IOS image, and try to boot from it (boot flash:iosimagename) but it will still go back into rommon mode. I also just swapped the RAM from my other 1760 into this 1760 and it booted up and went into normal configuraiton mode without any issues. However, the other router now will not load it's IOS image and I get the exact same error.I'm at a loss here, and have searched to figure out where or how I can just wipe the router clean to try and start fresh, but cannot get out or Rommon mode. The only thing I can think of is that the RAM went bad since it wont boot up either machine.
View 1 Replies
View Related
Sep 22, 2010
I've ended up in rommon mode on my new"old" RMA'ed ASA5505, and I'm stuck there, I'v tried to erase Disk0 and all that, and tftp'ed a new image into the box, but when booting I get the message :
INFO: Unable to read firewall mode from flash
WARNING: Unable to write firewall mode to flash, this is normal if flash is not formatted
Running Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000
This activattion key is invalid, use default settings only
i2c_write_byte_w_suspend() error, slot = 0x0, device = 0x40, address = 26 byte count =1. Reason: I2C_UNPOPULATED_ERROR
View 7 Replies
View Related
Feb 23, 2012
i try to recover cisco ASA 5505 IOS in Rommon mode but i have this message : [code]
View 1 Replies
View Related
Feb 9, 2012
I have one problem in my Client end router cisco 1841.
Everyday we switch on the router it will automatically goes to ROMMON mode.
So i take remotly and check wheather the IOS is corrupted or not.
So i use the command dir flash: to check IOS is available or not. i found the IOS is there.But it is not boot from IOS.
So i use the coomand boot xxxx.bin to boot from IOS.and finally it booted.
They told to use the coomand confreg in the ROMMON mode.
View 6 Replies
View Related
Dec 16, 2012
I have 6509 E. Actually what happen it last 3-4 times it reload its self and got stuck in rommon mode, i tried to boot it with boot by connecting a console cable on supervisor 720 2b. What and where is problem and why is stuck in rommon after reload.
View 11 Replies
View Related
Oct 5, 2008
I am trying normal password recovery for (cisco routers) for IAD 2400 but iam unable to get in rommon mode ?
View 3 Replies
View Related
Dec 12, 2012
I have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies
View Related
Jan 24, 2012
I have a 3550 switch that was replaced at a remote site with no IOS. This is a switch not a router so tftpdnld does not work.
[Code]...
The problem is the switches interface never comes up so try to connect to the tftp server. I read on google it can't be done on a switch to copy from tftp to flash in rommon mode on a switch and to use XMODEM. My problem is I do not have access to it, I ssh into a 3640 which is an access server for all devices and that is how I have console to it, how to use XMODEM over ssh.
But I'm fairly certain that there has to be a way to just copy it from tftp? I have a 3550 local and when I put it in rommon mode it stops the port check at port, port 1 goes from green when you plug it in to off then port 2 changes to amber and the rest green. So just by the look of this I would believe tftp would work; you just need to use port 1.
View 1 Replies
View Related
Jan 28, 2011
How can i Upgrade Catalyst 2960 switch software in Rommon mode (switch:)
Right now flash is empty.
View 7 Replies
View Related
Sep 17, 2012
I'm configuring a console server for configuring remote devices. This is working well except for the fact that if a target device is in ROMMON mode, the console server refuses to displays the target device console. It does open the connection but the ROMMON prompt is not shown on the console server . This is essential for this device as we will need to use it to reset passwords remotely and thus need to be able to access ROMMON mode from the console server.
Parts used are a 2951 router and a HWIC-8A serial card. Posted my config below:
[code]
Current configuration : 4389 bytes
!
[Code].....
View 1 Replies
View Related
Nov 28, 2012
We have a cisco catalyst 6509 with Supervisor Engine . After power outage, the switch always start in Rommon mode. Configuration register is 0X2102, we want to it always start in normal mode. What should i do?
View 3 Replies
View Related
Aug 7, 2012
I have a 512MB USB Flash device and was able to boot the IOS on the C2960 from it.After that i tried to Copy the IOS file from the USB to the system flash, but it could not find the USB Device.At plugging in the device the systems tells me: "Transfer type 2 not supported" I configured the USB device in NTFS and FAT both are able to boot with the ROMMON, but the normal system does not accept them and i know i can do the copy over a TFTP from my laptop, but it is strange that rommon accepts the usb device and the system does not?
View 1 Replies
View Related
Oct 21, 2012
I have one cisco 4507R+E.My question is if the IOS of the acive SUP crushed and the switch is running through it's second SUP then how to restore the IOS of the first SUP.Also how to access the ROMON mode of the crushed SUP when switch is running through second SUP.
View 1 Replies
View Related
Jan 30, 2012
I have an all gigE 3560. I don't use the management FE0 port on the back. I was thinking to use that for a 100Mbps WAN connection.
Seems to work just fine when I plugged in an test. But I am not routing across that link yet as I still need to setup the far end.
Is there any reason this would not work? I would like to not burn a gig port if the max throughput of the circuit is 100Mbps.
View 1 Replies
View Related
Jan 2, 2012
I have got ASA 5520. How to use the management port as a normal port on ASA. What are the basic reqirements for that.
View 3 Replies
View Related
Jan 19, 2012
What key sequence to go into ROMMON mode from the console port for VSS system with 2 VS-S720-10G?
View 3 Replies
View Related
Apr 26, 2012
I have a need to manage the 5505 outside of the 2 interfaces however I see it documented that Management access is only via the data path interface. This won't work for me because there will be NO management access on the data network being bridged through the firewall. Is there any option outside of going to routed mode or moving to the 5510?
View 1 Replies
View Related
Jun 13, 2012
How to set the management interface on a SG300 Switch in Layer 3 mode? I've some vlans configured on the switch with interfaces in each of them:
Vlan 100 (10.0.1.254 /24)
Vlan 200 (10.0.2.254 /24)
Vlan 300 (10.0.3.254 /24)
...
Vlan 900 (10.0.9.254 /24)
Now, the management interface is listening on all interfaces (IPs). But I would like to configure the switch to only listen on 10.0.9.254. What I need to configure or whether it is possible?
View 3 Replies
View Related
Aug 5, 2012
I can not even get in to management mode. In next program that just keeps trying to auto repair the connection and never displays any radio button option the direction state like "advanced settings".At the very least your PDF should match your user friendly **bleep** ware!The instructions even refer to itself wrong! It states "for manual set up go use browser connection section" then in that section it describes an auto set up and instructs you to follow the set up steps on the CD.
View 7 Replies
View Related
Jan 23, 2013
I have setup a 5515-X in transparent multi-mode and setup 5 security contexts with inside and outside ports, one admin and 4 others. The problem I have run into is setting up a management IP for each context. On one of my other transparent firewalls in production we were able to apply an IP to the security context (not interface) however the new firewall is running the latest software and this same functionality is not available. The only options for IP in context mode is IP AUDIT. So my next plan was to create sub-interfaces of the management interface and assign one to each context however the 5515-x does not allow sub-interfaces on the management interface. How I setup a management IP on each context?
Another interesting thing i read is that the managment IP assigned to a context (if i could figure out how to set it up), has to be in the same subnet as the data interface which if fine but it also says that the management interface should not be connected to the same switch as the data interface because of MAC address table update issues, meaning that i could not use a sub-interface of one of the already configured context ports.
View 3 Replies
View Related
Sep 13, 2012
I saw that the management port for the ASR 1006 has limited routing functionality according to the documentation. I know it "may" not be best practice but can I use this as a routed interface for the WAN port to our Internet or will this not work?
View 2 Replies
View Related
Nov 7, 2011
I have interfaces defined on the 5505:
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
[Code].....
I only need one interface to connect to a single host on the inside (VLAN1) and then connect E0 to a DSL.
Is it possible (are what are the commands required) to take one of the other interfaces and create a Management port on the local office LAN?
View 2 Replies
View Related
Nov 29, 2011
I just purchased 2 SF-300 48 port units for 2 customers. I want to be able to remotely manage them over the Internet with my browser. BUT, customer sites already use port 80 for web servers. So, how do I configure this switch to use some other port than 80?
I called support, and much to my surprise he said it cannot be changed. How bizarre that a device with many hundreds of configuration settings does not have one of the most basic settings...
At one customer site I can configure port forwarding and translation to get around this problem, but the other site's router does not offer port translation..
View 2 Replies
View Related
Jul 3, 2012
I'm having an issue with the 5508 management port .. I can't seem to ping it from the switch connected to it .. ( the Show cdp command shows that the two can see each other .. but no ping is possible ! [code]
View 4 Replies
View Related
Nov 6, 2011
i am currently trying to use LMS 3.2 Compliance management to verify and alter our access port configurations for 802.1x. Below is our current configuration
View 1 Replies
View Related
