Cisco :: Ap1231g-e-k9 - Load New Bin Ios In Rommon Mode?
Jun 9, 2011loading a new bin file onto a Cisco wirless access point ,the access point i have found is only in rommon stage
Access point model is : ap1231g-e-k9.
ADVERTISEMENT
Cisco Wireless :: AIR-AP1231G-E-K9 - Upgrading Autonomous Access Points To Lightweight Mode
Jun 6, 2013I have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies View RelatedCisco WAN :: 1841 - How To Do Configuration In ROMmon Mode
Mar 19, 2011On new 1841 Testing Router, I deleted the flash & did the reload. After reloading, instantly I entered into the Rommon mode. I have a backup of the flash in my TFTP Server, which is connected to the 1841 Router. how can I restore my flash file into my 1841 Router. I can not get myself out of Rommon mode. I also now even can not ping the TFTP Server as well. Do I have to configure in the Rommon mode ?
how to restore the flash image via TFTP Server on my 1841 Router.
Cisco WAN :: 2600 - Cannot Enter ROMmon Mode Or Key?
Apr 4, 2012I upgrade to a Flash 32mbs memory stick, as I reboot the 2600 Cisco router, it appear in the ROMMON mode, nonetheless, I followed some wrong procedure by changing components on the ROMMON command line. however now the router reboot or start with symbol only V2V2v2a, and I can no longer enter the ROMMON Mode or key anything in. I have a copy of the IOS on my TFTP server.
[Code]....
Cisco Switching/Routing :: Catalyst 2948G Boot Cannot Load Flash In Loop And No ROMmon
May 9, 2012i have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop :I know that the solution would be to download a new valid image from tftp via the rommon prompt but what i dont undertand is why i cant access the rommon prompt. It justs boots with the message above in a loop
View 0 Replies View RelatedCisco Switching/Routing :: Cannot Get Out Of Rommon Mode 1760
Dec 10, 2011I'm currently pursuing to take my CCNA and am currently studying for it, but have recently encountered a problem with one of my 1760 routers that I can not solve.Yesterday I went to boot up my router like normal, however when I went into hyperterminal I noticed the router was in Rommon mode. Thinking I could change the configuration registry, I tried to bypass the NVRAM by using confreg 0x2142. However this still causes the router to go into Rommon mode. I am getting an error that states that there is insufficient memory to load the IOS image. [code]
I have used the dir flash: command and can see the IOS image, and try to boot from it (boot flash:iosimagename) but it will still go back into rommon mode. I also just swapped the RAM from my other 1760 into this 1760 and it booted up and went into normal configuraiton mode without any issues. However, the other router now will not load it's IOS image and I get the exact same error.I'm at a loss here, and have searched to figure out where or how I can just wipe the router clean to try and start fresh, but cannot get out or Rommon mode. The only thing I can think of is that the RAM went bad since it wont boot up either machine.
Cisco Firewall :: ASA5505 Stuck In ROMmon Mode?
Sep 22, 2010I've ended up in rommon mode on my new"old" RMA'ed ASA5505, and I'm stuck there, I'v tried to erase Disk0 and all that, and tftp'ed a new image into the box, but when booting I get the message :
INFO: Unable to read firewall mode from flash
WARNING: Unable to write firewall mode to flash, this is normal if flash is not formatted
Running Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000
This activattion key is invalid, use default settings only
i2c_write_byte_w_suspend() error, slot = 0x0, device = 0x40, address = 26 byte count =1. Reason: I2C_UNPOPULATED_ERROR
Cisco WAN :: Management Port In ROMmon Mode - ASR1002
Jun 4, 2013Is it possible to use the mgmt port when in rommon mode? I use the Mgmt port when IOS is loaded and it works fine. I reboot the router, issue a break to put it in rommon and have set some variables but my Mgmt port never has link and I cannot ping it from the network. In rommon mode it looks like this:
PS1=rommon ! >
MCP_STARTUP_TRACEFLAGS=00000000:00000000
BOOT=bootflash:asr1000rp1-adventerprisek9.03.07.03.S.152-4.S3.bin,1;
IP_ADDRESS=10.71.50.101
IP_SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=10.71.50.3
BSI=0
RANDOM_NUM=1133006948
RET_2_RTS=13:38:27 EDT Wed Jun 5 2013
RET_2_RCALTS=1370453907
?=0
Cisco Firewall :: Recover ASA 5505 IOS In ROMmon Mode
Feb 23, 2012i try to recover cisco ASA 5505 IOS in Rommon mode but i have this message : [code]
View 1 Replies View RelatedCisco WAN :: 1841 - Router Automatically Goes To ROMmon Mode
Feb 9, 2012I have one problem in my Client end router cisco 1841.
Everyday we switch on the router it will automatically goes to ROMMON mode.
So i take remotly and check wheather the IOS is corrupted or not.
So i use the command dir flash: to check IOS is available or not. i found the IOS is there.But it is not boot from IOS.
So i use the coomand boot xxxx.bin to boot from IOS.and finally it booted.
They told to use the coomand confreg in the ROMMON mode.
Cisco Switching/Routing :: 6509 Stuck In ROMmon Mode?
Dec 16, 2012I have 6509 E. Actually what happen it last 3-4 times it reload its self and got stuck in rommon mode, i tried to boot it with boot by connecting a console cable on supervisor 720 2b. What and where is problem and why is stuck in rommon after reload.
View 11 Replies View RelatedCisco Switching/Routing :: 2400 - Unable To Get Into ROMmon Mode
Oct 5, 2008I am trying normal password recovery for (cisco routers) for IAD 2400 but iam unable to get in rommon mode ?
View 3 Replies View RelatedCisco Switching/Routing :: Catalyst 4506e - Booting In ROMmon Mode?
Dec 12, 2012I have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies View RelatedCisco Switching/Routing :: 3550 - Copy IOS To Switch In ROMmon Mode?
Jan 24, 2012I have a 3550 switch that was replaced at a remote site with no IOS. This is a switch not a router so tftpdnld does not work.
[Code]...
The problem is the switches interface never comes up so try to connect to the tftp server. I read on google it can't be done on a switch to copy from tftp to flash in rommon mode on a switch and to use XMODEM. My problem is I do not have access to it, I ssh into a 3640 which is an access server for all devices and that is how I have console to it, how to use XMODEM over ssh.
But I'm fairly certain that there has to be a way to just copy it from tftp? I have a 3550 local and when I put it in rommon mode it stops the port check at port, port 1 goes from green when you plug it in to off then port 2 changes to amber and the rest green. So just by the look of this I would believe tftp would work; you just need to use port 1.
Cisco WAN :: 2960 - Upgrade Catalyst Switch Software In ROMmon Mode?
Jan 28, 2011How can i Upgrade Catalyst 2960 switch software in Rommon mode (switch:)
Right now flash is empty.
Cisco :: 2951 - Access Server Not Displaying ROMmon Mode Target Device
Sep 17, 2012I'm configuring a console server for configuring remote devices. This is working well except for the fact that if a target device is in ROMMON mode, the console server refuses to displays the target device console. It does open the connection but the ROMMON prompt is not shown on the console server . This is essential for this device as we will need to use it to reset passwords remotely and thus need to be able to access ROMMON mode from the console server.
Parts used are a 2951 router and a HWIC-8A serial card. Posted my config below:
[code]
Current configuration : 4389 bytes
!
[Code].....
Cisco Switching/Routing :: Switch 6509 In ROMmon Mode After Power Outage?
Nov 28, 2012We have a cisco catalyst 6509 with Supervisor Engine . After power outage, the switch always start in Rommon mode. Configuration register is 0X2102, we want to it always start in normal mode. What should i do?
View 3 Replies View RelatedCisco Switching/Routing :: C2960 USB Flash Device Works In ROMmon But Not In Normal Mode?
Aug 7, 2012I have a 512MB USB Flash device and was able to boot the IOS on the C2960 from it.After that i tried to Copy the IOS file from the USB to the system flash, but it could not find the USB Device.At plugging in the device the systems tells me: "Transfer type 2 not supported" I configured the USB device in NTFS and FAT both are able to boot with the ROMMON, but the normal system does not accept them and i know i can do the copy over a TFTP from my laptop, but it is strange that rommon accepts the usb device and the system does not?
View 1 Replies View RelatedCisco Switching/Routing :: 4507R+E - Access ROMmon Mode Of Crushed SUP When Switch Running Through Second One
Oct 21, 2012I have one cisco 4507R+E.My question is if the IOS of the acive SUP crushed and the switch is running through it's second SUP then how to restore the IOS of the first SUP.Also how to access the ROMON mode of the crushed SUP when switch is running through second SUP.
View 1 Replies View RelatedCisco Application :: ACE30 Normal Load Balancing In Routed Mode
Sep 23, 2012We are in the situation we have a active configuration with ACE30 doing normal load balancing in routed mode, we have tons of rservers going out on a VIP.we now had to add a new private network to a provider that strangely enough does not want to see our public or private addresses. we need to loadbalance towards him on a priovided subnet (still rfc1918) (IOS VRF bug? is that correct?)I have two options, add the network (new interface) to the active loadbalancers (contexts) and then tie in new policies to the active serverfarms or make a new context just to load balance towards this provider.(preferred)Now - If I do this, the rservers see the client source addresses from this new provider. as the loadbalancer does not "hide" the client IP's. I would then have to add static routers toward the new context - I would want to skip that.
is there a way, to make the loadbalancer hide the client addresses towards the rservers ? perhaps I'm just needing the correct search term to find the config example.
Linksys Wired Router :: RV082 And Load Balancing Mode On 2 WAN?
Jul 2, 2007I have some problem connecting to sites when I'm using the router in Load Balancing mode on the 2 WAN. Looks that when a connection to a site is started with a WAN is not manteined with this one but jump from a wan to the other, causing, in some site like Home Banking to be disconnected every time. I would like to know if it's possible to configure the roouter in Load Balancing but Bindind the source and the destination IP address so the same wan will be used for the entire time this connection is up. In opther words the Load Balancing has a sense beetween connections not beetween the same connection.
View 9 Replies View RelatedCisco :: AIR-AP1231G-A-K9 Management IP?
Nov 18, 2012I have two dinasour APs that I need to fix. They are configured in bridge mode to bridge a few VLANs between two sites. Right now the management IP on BVI 3 interface doesn't work. Does it have to be on BVI1 for it to work? When I say "work" I mean I am able to ping it and use SNMP to monitor it.
View 1 Replies View RelatedCisco Wireless :: Using AIR-AP1231G-E-K9 As Repeater?
Apr 24, 2012I have an AIR-AP1131AG-E-K9 running as root AP with three SSID's (mbssid), all WPA-2 PSK, IOS 12.4(25d)JA Now I would like to use an AIR-AP1231G-E-K9 as repeater for one of the SSID's (all three are AFAIK not possible), IOS 12.3.8-JEE(ED) So only one SSID is used.
I use exactly the same shared secrets and security settings on both devices, on the repeater the SSID is designated as infrastructure-ssid.Unfortunately I have the problem that the repeater AP cannot associate with the root AP.I have verified that aironet extensions are enabled, same security settings are used and checked many sites on the net which describe how to configure a repeater AP. Is there any incompatibility between these two APs? I have two of the AIR-AP1231-G-E-K9 APs available, do I need to use the same models?
Cisco Wireless :: Adding A Second Ssid Air-ap1231g-a-k9?
Jun 20, 2012Version 12.3 I currently have an open authenication customer network, I would like to add a second securt ssid for my sales department, is this possible, how do I do this, the more specific the better .
View 1 Replies View RelatedCisco Wireless :: WLC 2504 Works With AIR-AP1231G-E-K9 And AIR-BR1310G-E-K9?
Feb 3, 2013Does WLC 2504 works with AIR-AP1231G-E-K9 and with AIR-BR1310G-E-K9 after I upgraded form AP to LAP the AP ?
View 4 Replies View RelatedCisco Wireless :: AP1231G - Failed To Add Device To WCS Reason
May 10, 2012I am trying to add an AP (1231G) with autonomous code (Version 12.3(8)JEC2) to WCS (v7.0.172.0). I recieved the following error:
Failed to add device to WCS Reason: Unified AP with same MacAddress already exists in WCS. Remove Unified AP first.
Cisco :: AP1231G-A-K9 Access Points / Very Slow Throughput
Jul 17, 2012I recently setup our small office network using the following setup:
Cablemodem <--> router <--> 1231AP(role root bridge with wireless clients) <-> 1231AP(role non-root bridge with wireless clients)Code on both APs: 12.3(8)JEE.Office network generally has less than 3 wireless clients connected at any one time to either AP. AP's are a mere 50' apart; clients are all less than 30' from either AP; they all show excellent signal and connected at 54mbps signaling rates.
All is/has been working very well & very stable with the exception of speed. We have business class service from RR, approx 25mbps dl, 2mbps ul. Any hardwired client to the router switch ports are able to download at speeds averaging 23mbps. Any wireless client connected to either AP is never able to exceed download speeds of 5mbps. With no other wireless clients connected except my one test client, I was not able to exceed 5mbps throughput from either AP that I connected to.
I can confirm that the ethernet connection between the router and root bridge is up at 100mbps-FD and not showing any errors: [code]
Are these very slow thoughput speeds normal of this hardware combination?I did much searching/googling and found claims that by eliminating TKIP it almost doubles the actual wireless speeds our clients can obtain.
Cisco Wireless :: Does VWLC Support AIR-AP1231G-A-K9 Platform
Mar 6, 2013Does the Cisco vWLC support the cisco AIR-AP1231G-A-K9 platform?
View 4 Replies View RelatedCisco Wireless :: Radius Server Authentication AIR-AP1231G-A-K9
Apr 30, 2012Below is he output from debug radius authentication from my AP.
I can see request is forwarding from AP to radius but Radius is not sending any response.Not sure why its not responding.
I also did not under stand few out outputs also
no sg in radius-timers and
RADIUS/DECODE: parse response no app start; FAIL
what does it mean.
I restarted radius server , changed secret key but no luck.
019639: May 1 16:15:08.727: RADIUS: User-Name [1] 32 "host/3KYGRH1.idcap.intdata.com"
019640: May 1 16:15:08.727: RADIUS: Framed-MTU [12] 6 1400
019641: May 1 16:15:08.727: RADIUS: Called-Station-Id [30] 16 "0012.01d6.f691"
[Code]...
Cisco Wireless :: Strange Power Failure With AIR-AP1231G
Mar 25, 2012I'm having the following issue with a couple of 1231's.
Some overall config info first:
This is a small office with 2x Catalyst 2950 (24-port, no PoE) switches and 4 AP1231G (autonomous). The APs get PoE from a PWRINJ3 each. The injectors are powered by the AP power supplies. Injectors and power supplies are mounted in the patch closet.
The 2 switches are connected together over 4 ports (20-23 on each switch), these ports are set to 1Q Trunk mode.
The APs are connected to the switches, 2 to each switch, on port 1-2. These ports again are configured as 1Q Trunk.
APs are connected to the switch as follows:
[switch] <- patch cable-> [injector] <- patch cable -> [patch panel] <- static cabling -> [outlet] <- patch cable -> [AP]
All this has been working without problems for a number of years.
A few weeks back, AP2 did not restart after a power cut (everything else did). All LEDs are off, port on switch has no LEDs lit. I did not get around to investigating this furtehr until last week. I unmounted (failed) AP2, took it to the spot where (working) AP3 hangs, and plugged it to the cable of AP3. AP2 came to life immediately. I unplugged it and plugged AP3 back in, which restarted immediately.
So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective.
On the same day, I notice AP4 is also dead (again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2).
So I order 2 new PWRINJ3s and for good measure 2 new power supplies. Later that day, I took the injector and power supply that fed AP4 out of the patch closet. When I try this combination (AP4, injector4 and P/S4), and connect it to a different wall outlet (and therefore a different port -16 - on the switch) IT WORKS! Should have triggered questions, but did not immediately.
Last Thursday I got the new injectors and power supplies. So I take one of each, hook them upto AP2 at my desk, and AP2 starts up. So I mount new injector2 and new P/S2 in the patch closet, put AP2 back in its place, connect all the cables - NOTHING. AP2 does not start. The "power" LED on the injecvtor lights up green, the "device status" LED remains off. I take AP2, new injector2 and new P/S2 to my desk, hook them upto a wall outlet (connected to switch port 17). AP2 starts immediately.
Meanwhile AP3 has (also) stopped working (no LEDs on at all). As far as I can tell, it stopped working after I briefly disconnected (and reconnected) the patch cable between injector3 and the patch panel in the patch closet. The LEDs on switch port 1 are off.
I have since tried to power cycle both switches (took power off both, waited a while, poewerd both back on). No change.
PS: the APs ran firmware 12.3(8)-JA until recently. AP1, AP3 and AP4 were upgraded to 12.3(8)-JEE after the the power cut that took AP2 out. THis is when I found out AP2 was dead. AP2 was still on 12.3(8)-JA. It was upgraded to 12.3(8)-JEE last week when it was on direct power on my desk.
Cisco Wireless :: AIR-AP1231G-A-K9 - Replicating Setup Across Heterogeneous APs
Oct 17, 2012I am trying now to deploy the setup that works on some APs and doesn't work on others.
For example, on an AIR-AP1231G-A-K9, the following setup works:
!
version 12.3
no service pad
service timestamps debug datetime msec
[Code].....
Cisco Wireless :: AIR-AP1231G-A-K9 And Controller Based Environment With Prime NCS
Apr 15, 2012I can't find any information that the AP1231G-A-K9 AP is supported in a 5508 Controller Based environment with Prime NCS.Could one of the experts confirm or deny?
View 1 Replies View RelatedCisco Wireless :: Replacing AP1231G-E-K9 (LEAP) With New 1260 / Will It Work
Aug 24, 2011iam currently trying to replace AP1231G-E-K9 with new equipment / Cisco AP next generation maybe?The problem is that the system, that is going to use the AP is using aironet 350 PCMCIA adapter with LEAP. If in fact we are going to use a new Cisco AP, will the new generation work with Aironet 350 Adapter and support LEAP?
View 2 Replies View Related