Version 12.3 I currently have an open authenication customer network, I would like to add a second securt ssid for my sales department, is this possible, how do I do this, the more specific the better .
View 1 RepliesWe have a CISCO WLAN in place with several SSIDs including one on the Voice VLAN. We need to add an additional one using CCKM due to wireless phone roaming issues. Does adding a new SSID to the WLAN cause any outage whatsoever? We are in an environment where even a small amount down time is not acceptable.
We are using two 5500 controllers with hundreds of LAP1142N
I have an AIR-AP1131AG-E-K9 running as root AP with three SSID's (mbssid), all WPA-2 PSK, IOS 12.4(25d)JA Now I would like to use an AIR-AP1231G-E-K9 as repeater for one of the SSID's (all three are AFAIK not possible), IOS 12.3.8-JEE(ED) So only one SSID is used.
I use exactly the same shared secrets and security settings on both devices, on the repeater the SSID is designated as infrastructure-ssid.Unfortunately I have the problem that the repeater AP cannot associate with the root AP.I have verified that aironet extensions are enabled, same security settings are used and checked many sites on the net which describe how to configure a repeater AP. Is there any incompatibility between these two APs? I have two of the AIR-AP1231-G-E-K9 APs available, do I need to use the same models?
Does WLC 2504 works with AIR-AP1231G-E-K9 and with AIR-BR1310G-E-K9 after I upgraded form AP to LAP the AP ?
View 4 Replies View RelatedI am trying to add an AP (1231G) with autonomous code (Version 12.3(8)JEC2) to WCS (v7.0.172.0). I recieved the following error:
Failed to add device to WCS Reason: Unified AP with same MacAddress already exists in WCS. Remove Unified AP first.
Does the Cisco vWLC support the cisco AIR-AP1231G-A-K9 platform?
View 4 Replies View RelatedBelow is he output from debug radius authentication from my AP.
I can see request is forwarding from AP to radius but Radius is not sending any response.Not sure why its not responding.
I also did not under stand few out outputs also
no sg in radius-timers and
RADIUS/DECODE: parse response no app start; FAIL
what does it mean.
I restarted radius server , changed secret key but no luck.
019639: May 1 16:15:08.727: RADIUS: User-Name [1] 32 "host/3KYGRH1.idcap.intdata.com"
019640: May 1 16:15:08.727: RADIUS: Framed-MTU [12] 6 1400
019641: May 1 16:15:08.727: RADIUS: Called-Station-Id [30] 16 "0012.01d6.f691"
[Code]...
I'm having the following issue with a couple of 1231's.
Some overall config info first:
This is a small office with 2x Catalyst 2950 (24-port, no PoE) switches and 4 AP1231G (autonomous). The APs get PoE from a PWRINJ3 each. The injectors are powered by the AP power supplies. Injectors and power supplies are mounted in the patch closet.
The 2 switches are connected together over 4 ports (20-23 on each switch), these ports are set to 1Q Trunk mode.
The APs are connected to the switches, 2 to each switch, on port 1-2. These ports again are configured as 1Q Trunk.
APs are connected to the switch as follows:
[switch] <- patch cable-> [injector] <- patch cable -> [patch panel] <- static cabling -> [outlet] <- patch cable -> [AP]
All this has been working without problems for a number of years.
A few weeks back, AP2 did not restart after a power cut (everything else did). All LEDs are off, port on switch has no LEDs lit. I did not get around to investigating this furtehr until last week. I unmounted (failed) AP2, took it to the spot where (working) AP3 hangs, and plugged it to the cable of AP3. AP2 came to life immediately. I unplugged it and plugged AP3 back in, which restarted immediately.
So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective.
On the same day, I notice AP4 is also dead (again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2).
So I order 2 new PWRINJ3s and for good measure 2 new power supplies. Later that day, I took the injector and power supply that fed AP4 out of the patch closet. When I try this combination (AP4, injector4 and P/S4), and connect it to a different wall outlet (and therefore a different port -16 - on the switch) IT WORKS! Should have triggered questions, but did not immediately.
Last Thursday I got the new injectors and power supplies. So I take one of each, hook them upto AP2 at my desk, and AP2 starts up. So I mount new injector2 and new P/S2 in the patch closet, put AP2 back in its place, connect all the cables - NOTHING. AP2 does not start. The "power" LED on the injecvtor lights up green, the "device status" LED remains off. I take AP2, new injector2 and new P/S2 to my desk, hook them upto a wall outlet (connected to switch port 17). AP2 starts immediately.
Meanwhile AP3 has (also) stopped working (no LEDs on at all). As far as I can tell, it stopped working after I briefly disconnected (and reconnected) the patch cable between injector3 and the patch panel in the patch closet. The LEDs on switch port 1 are off.
I have since tried to power cycle both switches (took power off both, waited a while, poewerd both back on). No change.
PS: the APs ran firmware 12.3(8)-JA until recently. AP1, AP3 and AP4 were upgraded to 12.3(8)-JEE after the the power cut that took AP2 out. THis is when I found out AP2 was dead. AP2 was still on 12.3(8)-JA. It was upgraded to 12.3(8)-JEE last week when it was on direct power on my desk.
I am trying now to deploy the setup that works on some APs and doesn't work on others.
For example, on an AIR-AP1231G-A-K9, the following setup works:
!
version 12.3
no service pad
service timestamps debug datetime msec
[Code].....
I can't find any information that the AP1231G-A-K9 AP is supported in a 5508 Controller Based environment with Prime NCS.Could one of the experts confirm or deny?
View 1 Replies View Relatediam currently trying to replace AP1231G-E-K9 with new equipment / Cisco AP next generation maybe?The problem is that the system, that is going to use the AP is using aironet 350 PCMCIA adapter with LEAP. If in fact we are going to use a new Cisco AP, will the new generation work with Aironet 350 Adapter and support LEAP?
View 2 Replies View RelatedWe have this access point AIR-AP1231G-A-K9 for mobile users. current version is c1200-k9w7-mx.123-7.JA4. Sometimes users are able to associate but not getting IP address from dhcp. It shows 0.0.0.0 for the particular client.
View 2 Replies View RelatedI have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies View RelatedI have two dinasour APs that I need to fix. They are configured in bridge mode to bridge a few VLANs between two sites. Right now the management IP on BVI 3 interface doesn't work. Does it have to be on BVI1 for it to work? When I say "work" I mean I am able to ping it and use SNMP to monitor it.
View 1 Replies View Relatedloading a new bin file onto a Cisco wirless access point ,the access point i have found is only in rommon stage
Access point model is : ap1231g-e-k9.
I recently setup our small office network using the following setup:
Cablemodem <--> router <--> 1231AP(role root bridge with wireless clients) <-> 1231AP(role non-root bridge with wireless clients)Code on both APs: 12.3(8)JEE.Office network generally has less than 3 wireless clients connected at any one time to either AP. AP's are a mere 50' apart; clients are all less than 30' from either AP; they all show excellent signal and connected at 54mbps signaling rates.
All is/has been working very well & very stable with the exception of speed. We have business class service from RR, approx 25mbps dl, 2mbps ul. Any hardwired client to the router switch ports are able to download at speeds averaging 23mbps. Any wireless client connected to either AP is never able to exceed download speeds of 5mbps. With no other wireless clients connected except my one test client, I was not able to exceed 5mbps throughput from either AP that I connected to.
I can confirm that the ethernet connection between the router and root bridge is up at 100mbps-FD and not showing any errors: [code]
Are these very slow thoughput speeds normal of this hardware combination?I did much searching/googling and found claims that by eliminating TKIP it almost doubles the actual wireless speeds our clients can obtain.
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
possible solutions to add the wireless LAN to wired LAN of the organization for providing the flexibility in accessing the organization services i.e.,which type of hardware is needed and what changes i have to do and suggest me the best solution in terms of speed,distance, cost for redesigning, cost for training for the employees, maintenance cost, security.
View 3 Replies View RelatedWe have an inner office wired system that we do NOT want connected to the internet. Right now we have a 20 port either switch or router (not sure which one). We want to add another computer, but can not run the ethernet wires to this location so we wanted to find out if we just need to plug in a wireless router to the router/switch that is there to give that computer access to our office network.We do not have or need internet...we just need to be able to share a networked program both wired and wirelessly.
View 1 Replies View RelatedI currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies View RelatedI have WLC 5508 with 12aps license, i will buy a new license with 50 Aps, my question, its possible add new license with 50 aps, totaling 62 aps licenses?
View 7 Replies View RelatedWhen I tried to add new AP 1242 to my network I had following problem:
The Ap was constantly reloading and I was getting message
Wed Mar 20 13:32:12 2013 AP 'UBFT-E06-F0A-R09-0022.901b.a6ba', MAC: 00:23:ab:27:1f:30 disassociated previously due to AP Reset.
%CAPWAP-3-IMAGE_DOWNLOAD_ERR3: capwap_ac_platform.c:782 Refusing image download request from AP - unable to open image file /mnt/ap_bundle/ap.pri//c1240
I decidet to reinstall software on WISM 2 modul (7.2.111.3) this fix the problem and AP joined controller but during this process I have lost connection to 87 AP for 3 seconds and then they joind back again.
"disassociated previously due to AP Reset"
I am trying to add a 2nd wireless access point to my network at work basically to allow a better wireless signal on a 2nd floor.1st Access Point is a LInksys WAP54G Wireless G Access Point.I had a Belkin F5D7234-4 ver 4 G Wireless Router at home that I brought in to use as the 2nd access point. IP info on the Linksys is 192.168.1.245, subnet is 255.255.255.0, Gateway is 192.168.1.1.The Belkin has been reset to factory defauts so IP is 192.168.2.1.If I connect my PC directly to the router using one of the wired ports not the modem port, I can access the router webpage.As soon as I enable access point mode and change the router IP to 192.168.1.246,I lose the router and cannot access it at all to finish the network configuration.
View 6 Replies View RelatedI currently have a wired network which starts with a cable router downstairs which is a virgin media netgear box with firewall and DHCP turned on. I have a NAS server and a smart tv which run off ethernet connections to this router.then have a cable run upstairs to a TPlink gigabit switch which is connected to a PC and a printer (in my study). All this works just fine, no configuration needed.I have a TPlink wireless router, a TL-WR743ND. I want to use this to connect to the switch upstairs (not downstairs - my stone walls limit any wireless access point) to provide wireless network coverage for my house.So I figured I should configure it with a dynamic IP address (ie it gets it from the netgear DHCP), turn off the TPLink's DHCP and firewall, and then any wireless devices attached to the TPLink by wireless should have access to printer and NAS
View 8 Replies View RelatedI own a Panasonic DMP-BD80 Bluray player. It has both an ethernet connection and a USB port. I'd like to add the Bluray player to my wireless network but I don't know what equiptment to buy or how to install it.
View 4 Replies View Relatedthe pc im trying to connect to a wireless network was previously on but when the OS was changed it failed to connect back on the network. what should i do?
View 1 Replies View RelatedI have att uverse which is wireless G. I want to add a 2nd router behind it that will have wireless N. I've made the connection. I see it on my list of networks but doesn't allow me to access it.
View 2 Replies View RelatedI'm trying to add a new laptop to our current wireless network. I need the security key and an easy way to locate it.
View 1 Replies View Relatedhow do i add a computer to my wireless router
View 1 Replies View RelatedI am not a tech person, so I apologize if this is a dumb question. Tech supportme because no one wants to comment on if/how to attach equipment manufactured by some other company.I have a wireless home network using a Netgear DGN2280 router/modem. I also have an HP Officejet 5800 printer that I would like to add to the network. This is a USB printer that DOES NOT have a network card of any kind.I have heard of a print server, and know that it obviously has to do with hooking a printer to a network, but don't know if it will work in my application. Will this work for me?I just now noticed that there is a USB port on the back of the router/modem. can I hook my printer up to that port (and leave it hooked up) and print across the wireless network? I don't care if my printer has to be wired to something. I would just prefer that my laptop not have to be wired directly to the printer.
View 5 Replies View RelatedI`m trying to set up a relative`s Internet up so that it is wireless; currently the router takes signal from cable, not phone, is wired only, and has just one ethernet port. I know the number of ports can easily be expanded using a switch, but is it possible to buy a piece of hardware which could be plugged into the router to broadcast a wireless signal as well? I have looked quite thoroughly for anything that could do this but I`m pretty new to networking
View 7 Replies View RelatedI'm trying to connect another computer to our household wireless network. I have the security key but I can't get a window to come up asking for it when I click on our family network. How do I get a box to come up asking for the key?
View 3 Replies View RelatedShe has comcast xfinity with a the SMCD3GNV router which if you ever look it up has the worst wireless signal imaginable and I can second that. I was hoping to not have to touch the SMCD3GNV router and just add on to it by attaching a secondary router as a wap.What I plan to do (which I am sure has been exasterbated in forums but just want clarity) was to disable DHCP on the new n router ( cheaper than official wap) and set ip out of SMCD3GNV router DHCP ip range but in same subnet mask so probably 192.168.1.2. Then connect the SMCD3GNV router to the new router via ethernet and dont use wan port. Is this basically all I have to do? Do I need to change the channels on either devices since their next to eachother? or will them being next to eachother and same channel cause interference? I have read I can call comcast and turn the smcd3gnv into a bridge ( plain modem) but I would rather avoid calling them and see if 2 wireless access points next to eachother is okay.Also, I plan on doing this by going to microcenter.com and getting a router for 24.99 or less with a coupon I have. Is there any on their website that you would recommend for this setup? Also if you could check the wap on their website and see if you think its worth it to get one of those instead if under that price as well. I want to utilize wireless n signal . Also, the xfinity service she has is rated for 50mbps download and cannot remember the upload , I have tested this wired and it does actually achieve this or greater.
View 5 Replies View Related