Cisco Wireless :: WLC 2504 Works With AIR-AP1231G-E-K9 And AIR-BR1310G-E-K9?
Feb 3, 2013Does WLC 2504 works with AIR-AP1231G-E-K9 and with AIR-BR1310G-E-K9 after I upgraded form AP to LAP the AP ?
View 4 Replies
ADVERTISEMENT
Cisco Wireless :: AIR-BR1310G-E-K9 Bridged Usage
Sep 19, 2012Is it possible to build two separate bridged connections from one "base"?
I'd need to connect to two other buildings which luckily happen to be quite on the same direction (antennawise). how to configure this into the devices I call "base", "building1" and "building2". The first building is about 50 meters and the other about 120 meters away. 11Mbps would be adequate for both. A some kind of encryption would be needed.
Cisco Wireless :: Power Over Ethernet For AIR-BR1310G
Dec 12, 2012i have AIR-BR1310G that came with its proper power injector AIR-PWRINJ-BLR2 can this power injector be feed using a POE switch or do i have to use the 48v power adapter
View 1 Replies View RelatedCisco Wireless :: Flash Image For Air BR1310G-A
Dec 22, 2012I purchased a used AIR BR1310G-A--K9-R from a local high school that was rebuilding their athletic field. The AP was used for communications for their pressbox staff. The AIR BR1310G was part of the schools campus wide WiFi network and was upgraded to an lwapp image c1310-k9w8-m 12.4 3c JA. Our home sits on a large lot and I would like to convert the BR1310G back to an autonomous AP.
In order convert it back to an automonous AP, I will need the original image. The school used a contractor for their WiFi network and they do not have a backup of the original image. I do not have a service account with Cisco so downloading the autonomous image from the Cisco website is out. What are my options for either obtaining an image file or using the current managed image without a WLC?
Cisco Wireless :: Using AIR-AP1231G-E-K9 As Repeater?
Apr 24, 2012I have an AIR-AP1131AG-E-K9 running as root AP with three SSID's (mbssid), all WPA-2 PSK, IOS 12.4(25d)JA Now I would like to use an AIR-AP1231G-E-K9 as repeater for one of the SSID's (all three are AFAIK not possible), IOS 12.3.8-JEE(ED) So only one SSID is used.
I use exactly the same shared secrets and security settings on both devices, on the repeater the SSID is designated as infrastructure-ssid.Unfortunately I have the problem that the repeater AP cannot associate with the root AP.I have verified that aironet extensions are enabled, same security settings are used and checked many sites on the net which describe how to configure a repeater AP. Is there any incompatibility between these two APs? I have two of the AIR-AP1231-G-E-K9 APs available, do I need to use the same models?
Cisco Wireless :: Adding A Second Ssid Air-ap1231g-a-k9?
Jun 20, 2012Version 12.3 I currently have an open authenication customer network, I would like to add a second securt ssid for my sales department, is this possible, how do I do this, the more specific the better .
View 1 Replies View RelatedCisco Wireless :: AP1231G - Failed To Add Device To WCS Reason
May 10, 2012I am trying to add an AP (1231G) with autonomous code (Version 12.3(8)JEC2) to WCS (v7.0.172.0). I recieved the following error:
Failed to add device to WCS Reason: Unified AP with same MacAddress already exists in WCS. Remove Unified AP first.
Cisco Wireless :: Does VWLC Support AIR-AP1231G-A-K9 Platform
Mar 6, 2013Does the Cisco vWLC support the cisco AIR-AP1231G-A-K9 platform?
View 4 Replies View RelatedCisco Wireless :: Radius Server Authentication AIR-AP1231G-A-K9
Apr 30, 2012Below is he output from debug radius authentication from my AP.
I can see request is forwarding from AP to radius but Radius is not sending any response.Not sure why its not responding.
I also did not under stand few out outputs also
no sg in radius-timers and
RADIUS/DECODE: parse response no app start; FAIL
what does it mean.
I restarted radius server , changed secret key but no luck.
019639: May 1 16:15:08.727: RADIUS: User-Name [1] 32 "host/3KYGRH1.idcap.intdata.com"
019640: May 1 16:15:08.727: RADIUS: Framed-MTU [12] 6 1400
019641: May 1 16:15:08.727: RADIUS: Called-Station-Id [30] 16 "0012.01d6.f691"
[Code]...
Cisco Wireless :: Strange Power Failure With AIR-AP1231G
Mar 25, 2012I'm having the following issue with a couple of 1231's.
Some overall config info first:
This is a small office with 2x Catalyst 2950 (24-port, no PoE) switches and 4 AP1231G (autonomous). The APs get PoE from a PWRINJ3 each. The injectors are powered by the AP power supplies. Injectors and power supplies are mounted in the patch closet.
The 2 switches are connected together over 4 ports (20-23 on each switch), these ports are set to 1Q Trunk mode.
The APs are connected to the switches, 2 to each switch, on port 1-2. These ports again are configured as 1Q Trunk.
APs are connected to the switch as follows:
[switch] <- patch cable-> [injector] <- patch cable -> [patch panel] <- static cabling -> [outlet] <- patch cable -> [AP]
All this has been working without problems for a number of years.
A few weeks back, AP2 did not restart after a power cut (everything else did). All LEDs are off, port on switch has no LEDs lit. I did not get around to investigating this furtehr until last week. I unmounted (failed) AP2, took it to the spot where (working) AP3 hangs, and plugged it to the cable of AP3. AP2 came to life immediately. I unplugged it and plugged AP3 back in, which restarted immediately.
So I suspect a power supply issue on AP2. I took the injector and power supply that fed AP2 out of the patch closet. When connecting AP2 directly to the power supply, it came to life immediately. So I figure the injector is defective.
On the same day, I notice AP4 is also dead (again all LEDs off, no idea how long, could have been that day or could have been a few days - it has definitely been working after the power cut that appeared to have killed AP2).
So I order 2 new PWRINJ3s and for good measure 2 new power supplies. Later that day, I took the injector and power supply that fed AP4 out of the patch closet. When I try this combination (AP4, injector4 and P/S4), and connect it to a different wall outlet (and therefore a different port -16 - on the switch) IT WORKS! Should have triggered questions, but did not immediately.
Last Thursday I got the new injectors and power supplies. So I take one of each, hook them upto AP2 at my desk, and AP2 starts up. So I mount new injector2 and new P/S2 in the patch closet, put AP2 back in its place, connect all the cables - NOTHING. AP2 does not start. The "power" LED on the injecvtor lights up green, the "device status" LED remains off. I take AP2, new injector2 and new P/S2 to my desk, hook them upto a wall outlet (connected to switch port 17). AP2 starts immediately.
Meanwhile AP3 has (also) stopped working (no LEDs on at all). As far as I can tell, it stopped working after I briefly disconnected (and reconnected) the patch cable between injector3 and the patch panel in the patch closet. The LEDs on switch port 1 are off.
I have since tried to power cycle both switches (took power off both, waited a while, poewerd both back on). No change.
PS: the APs ran firmware 12.3(8)-JA until recently. AP1, AP3 and AP4 were upgraded to 12.3(8)-JEE after the the power cut that took AP2 out. THis is when I found out AP2 was dead. AP2 was still on 12.3(8)-JA. It was upgraded to 12.3(8)-JEE last week when it was on direct power on my desk.
Cisco Wireless :: AIR-AP1231G-A-K9 - Replicating Setup Across Heterogeneous APs
Oct 17, 2012I am trying now to deploy the setup that works on some APs and doesn't work on others.
For example, on an AIR-AP1231G-A-K9, the following setup works:
!
version 12.3
no service pad
service timestamps debug datetime msec
[Code].....
Cisco Wireless :: AIR-AP1231G-A-K9 And Controller Based Environment With Prime NCS
Apr 15, 2012I can't find any information that the AP1231G-A-K9 AP is supported in a 5508 Controller Based environment with Prime NCS.Could one of the experts confirm or deny?
View 1 Replies View RelatedCisco Wireless :: Replacing AP1231G-E-K9 (LEAP) With New 1260 / Will It Work
Aug 24, 2011iam currently trying to replace AP1231G-E-K9 with new equipment / Cisco AP next generation maybe?The problem is that the system, that is going to use the AP is using aironet 350 PCMCIA adapter with LEAP. If in fact we are going to use a new Cisco AP, will the new generation work with Aironet 350 Adapter and support LEAP?
View 2 Replies View RelatedCisco Wireless :: AIR-AP1231G-A-K9 Standalone Access Point- Disconnection
Jun 9, 2013We have this access point AIR-AP1231G-A-K9 for mobile users. current version is c1200-k9w7-mx.123-7.JA4. Sometimes users are able to associate but not getting IP address from dhcp. It shows 0.0.0.0 for the particular client.
View 2 Replies View RelatedCisco Wireless :: AIR-AP1231G-E-K9 - Upgrading Autonomous Access Points To Lightweight Mode
Jun 6, 2013I have AP AIR-AP1231G-E-K9 with iOS c1200-k9w7-tar.123-7.JA2 and I want to convert it to Lightweight Mode with iOS image c1200-rcvk9w8 tar.124-21a.JA2. First of all, is it possible? Because I tried to convert from tftp server command (archive download-sw /overwrite /reload tftp://ipaddress/image.tar) and I cannot see in the controller. (controller and aps are in the same network)
View 11 Replies View RelatedCisco :: AIR-AP1231G-A-K9 Management IP?
Nov 18, 2012I have two dinasour APs that I need to fix. They are configured in bridge mode to bridge a few VLANs between two sites. Right now the management IP on BVI 3 interface doesn't work. Does it have to be on BVI1 for it to work? When I say "work" I mean I am able to ping it and use SNMP to monitor it.
View 1 Replies View RelatedCisco :: Ap1231g-e-k9 - Load New Bin Ios In Rommon Mode?
Jun 9, 2011loading a new bin file onto a Cisco wirless access point ,the access point i have found is only in rommon stage
Access point model is : ap1231g-e-k9.
Wireless :: Wireless Not Works But Wired Network Works
Apr 6, 2011this computer was working on this router no problem. computer crashed and noiw computer is fine i connected it to my cable from ny desk top comutyer and works fine. It just cannot hook up to the wireless connection?
View 1 Replies View RelatedCisco :: AP1231G-A-K9 Access Points / Very Slow Throughput
Jul 17, 2012I recently setup our small office network using the following setup:
Cablemodem <--> router <--> 1231AP(role root bridge with wireless clients) <-> 1231AP(role non-root bridge with wireless clients)Code on both APs: 12.3(8)JEE.Office network generally has less than 3 wireless clients connected at any one time to either AP. AP's are a mere 50' apart; clients are all less than 30' from either AP; they all show excellent signal and connected at 54mbps signaling rates.
All is/has been working very well & very stable with the exception of speed. We have business class service from RR, approx 25mbps dl, 2mbps ul. Any hardwired client to the router switch ports are able to download at speeds averaging 23mbps. Any wireless client connected to either AP is never able to exceed download speeds of 5mbps. With no other wireless clients connected except my one test client, I was not able to exceed 5mbps throughput from either AP that I connected to.
I can confirm that the ethernet connection between the router and root bridge is up at 100mbps-FD and not showing any errors: [code]
Are these very slow thoughput speeds normal of this hardware combination?I did much searching/googling and found claims that by eliminating TKIP it almost doubles the actual wireless speeds our clients can obtain.
Cisco Wireless :: Why POE In 2504 - Cannot Be Used For AP
Mar 2, 2013Why a 2504 Poe? If it can not be used for AP.
View 10 Replies View RelatedCisco Wireless :: WLC 2504 - Upgrade From 7.2. To 7.4?
Jan 22, 2013I'm planning to upgrade our WLC 2504 from 7.2.111.3 to 7.4.100.0 but the cisco site says "WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time" Is it something about NCS? we have only 1 cisco WLC 2504 and 6 1142APs.. Also let me know is it possible to go directly from 7.2 to 7.4 ?
View 8 Replies View RelatedCisco Wireless :: WLC 2504 Max AP Support?
Nov 28, 2012what is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
Cisco Wireless :: WLC 2504 - Some Clients Gets IP As Zero
Aug 29, 2012I've problem with a WLC 2504. Some Clients like phones and Thin Clients get an IP 0.0.0.0.Software Version is 7.0.235.0. Test with a Laptop seams to be OK. Some printers also got an 0.0.0.0.Around 30% are not OK. also had the log: Impersonation of AP with Base Radio MAC 00:yy:yy:yy:yy:yyusing source address of 00:xx:xx:xx:xx:xx has been detected by the AP with MAC Address: 00:yy:yy:yy:yy:yy on its 802.11b/g radio whose slot ID is 0 The problem is, I cannot go to 7.2 version because I have 2 x AP 1231 and 2 x 1242 AP's.1231 AP's are not anymore supported in 7.2 Version.
View 14 Replies View RelatedCisco Wireless :: Two WLC 2504 In Same Network?
Aug 15, 2012I have two WLC 2504 controllers. These controllers are for two different buildings. But they share a VLAN, and network address range. How can I control the access points to the register selected only at a specific controller.
Example:
AP 1 -> WLC 1
AP 2 -> WLC 2
AP 3 -> WLC 1
Since the buildings also broadcast in different SSID. The two controllers are in a mobility group.
Cisco Wireless :: WLC 2504 IOS Update?
Jul 12, 2012If we update our ios on WLC do we have to add the certificate for AP's again or we don't need to do that.
View 4 Replies View RelatedCisco Wireless :: 2504 - WLC 7.4.100.0 Downgrade
Mar 13, 2013Some time ago I updated a WLC, model 2504, from version 7.3 to 7.4.100.0. I also update the FUS (Field Upgrade Software) to the latest release, 1.8.0.0. Now I need to downgrade the WLC back to 7.3 version.
My doubt is: Can I just take the normal processes and downgrade the WLC back to 7.3, even with the FUS in version 1.8.0.0?
Cisco Wireless :: 2504 - AP Cannot Join WLC
Jun 10, 2013I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Cisco Wireless :: Adding A Second 2504 AP Controller
Aug 2, 2012I currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies View RelatedCisco Wireless :: WLC 2504 Not Join AP1130ag?
Mar 12, 2013I have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch 2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?
View 4 Replies View RelatedCisco Wireless :: AP 1524 Not Getting Joined With 2504 WLC
Jul 3, 2012I've got a 1524 ap and it wont join my 2540 WLC. The messages I see in the WLC is RADIUS authorization is pending for the AP. I've added the MAC address of the ap under AP Policies using MIC. I dont have a radius server either so not sure how to tackle this one.When I run debug capwap events enale under the wlc I see the following messages:Discarding discovery request in LWAPP from AP supporting CAPWAP.
View 35 Replies View RelatedCisco Wireless :: 2504 WLC And AirLAP1131AG-E-K9 Not Registering?
May 20, 2012We have a 2504 on version 7.2.103.0 and 15 of the 1131 AG's.In short we cannot get the access points to register against the WLC, they seem to be caught up in a boot loop. They are seen on the WLC with a status of downloading, then once they have downloaded (Seen via CLI) I get an error message things I can confirm are The Country code is set to GB All ports are in Native VLAN Access points are ETSI type. It stops and restarts at syslog output DTLS-3-BAD-RECORD: Erroneous record recieved from x.x.x.x: Duplicate (replayed) record.
View 26 Replies View RelatedCisco Wireless :: 2504 WLC Tunneling To 5508?
Oct 14, 2012Can a 2504 WLC on a remote site provide guest access on one SSID, drop taht out locally on that site and provide corporate access on a second WLC that it then tunnls to a 5508 at the main corporate site ?
View 4 Replies View RelatedCisco Wireless :: Upgrade Controller 2504 From 7.0 To 7.4?
Jun 16, 2013upgrade on the wireless controller 2504 from 7.0 to 7.4 is direct upgrade.My customer faced problem by upgrading the software 7.0 to 7.4 directly and the image hang.how should proceed recover the image 7.4/
View 7 Replies View Related