this computer was working on this router no problem. computer crashed and noiw computer is fine i connected it to my cable from ny desk top comutyer and works fine. It just cannot hook up to the wireless connection?
View 1 RepliesI have a brand new broadband service in my new house.The problem I have and the ISP support cannot understand is that using my laptop in i connect wirelessly to internet as soon as i request a page the router losing connection to the internet.But I can use my smartphone wirelessly that does not cause router any problems.If I use the lan cable the internet is fine and only disconnects every now and again.
View 1 Replies View RelatedMy computer not working probably with a wired connection.I can ping to the problem sites with absolutely no issues.
View 3 Replies View RelatedIntalled a new router (Linksys Cloud 1200) yesterday. Immediately after that the 2 computers that were connected to the network could no longer access the internet. My laptop and my ipad can access the internet wirelessly. The laptop which was not connected to the network when I connected the router can access the network both wirelessly and wired. Printers attached to the network will print without a problem.Finally I took an old computer out of storage (running WinXP) and hooked it up to the wired network. It too has no problems accessing the network. So have to assume the issue is a software issue with the two computers that were hooked up to the network when I changed the router.I have read the posts here - I did a stack reset on one of the computers but no luck. I removed Norton 360 and Team Viewer which in other posts people said they had issues with...to no avail.
Since I dont have a wireless connection to the 2 computers that cannot access the internet - I cannot download TSG SysInfo. However here I did copy the ipconfig lines below from the desktop thats not responding. [code] Was working fine until I replaced the router. I tried going back to the oldrouter (Netgear) same issue - no wired internet connectivity.
problem started a few months ago. wireless kept crashing. tracked it down to seeing it crash when certain Win7 Dell laptop tried to connect. (Laptop is company owned with standard type of corporate AD authentication and image) my wireless setting use WPA2 personal with AES encryption. use both N & G, auto rate and scan.any time this laptop connected the wireless crashed, other devices didn't show SSID (both main and guest)But wired connection continued to work fine.
View 1 Replies View RelatedMY ISP is AT&T. I have their Westell DSL modem, with a bridged connection to a Linksys wireless router. The router is connected via ethernet to a dead computer: a 7 year-old Dell desktop that will boot up but shut down right away. I have been able to connect multiple laptops wirelessly to this network. I thought an ethernet connection was required in a home network such as mine? The cable has been plugged into a dead computer for several months and frankly I'd like to get rid of the desktop. What exactly is the ethernet requirement - just to be plugged into a port? Could I theoretically just yank the ethernet card out of the desktop and use it instead of the whole dead system?
View 5 Replies View RelatedI'm trying to set up a wireless network for my parents. I have a Belkin Play N600 router (model F7D8302) that I'm trying to hook up to an Acer desktop running Vista. The modem is a Siemens Speed stream 4100. I have a cable going from the ethernet port of the modem to the modem port on the router. The pc is connected to one of the other four ports in the router. The wireless works fine, but I can't get the wired connection on the desktop working. The Internet light on the modem is not on, but the modem works fine when connected directly to the pc. I've tried power cycling and resetting everything, but it's still not working.
View 9 Replies View RelatedI have a Cisco linksys router e1550. My wireless network is working fine, but my wired (PC) is not working?
Removing the router and having the modem connected to my PC works but when I put on my router my wired connection only works for a few seconds to none
So I think the router may be causing it, could it be the settings? Even though there at default.
I have my internet hooked up to a DSL Modem and a Wireless Router. But I had configured the Wireless Router wrong that I couldn't connect to it using a WiFi. I was going to reconfigure it but the Netgear Router was outdated that their reconfiguring URL no longer existed. So I went out and got a *NEW* Netgear Router. Prior to the *NEW* Router I had a Laptop and a PC connected via DSL Cable connected in the Wireless Router. Now with the *NEW* Router I had just purchased I connected everything just like I had done with my previous Router. Wireless Connect works great but I can't connected using the DSL Cable connection. It does not respond. I tried connecting the cables to different ports but it didn't work. My PC mainly needs the wired connection cuz it's where I play my Online games. I tried playing with my Wireless connect but it lags very bad. How to get the wired connections to work? Netgear N600 Wireless and Dual Band Router
View 3 Replies View RelatedAbout 6 months ago I bought a new router (Linksys E1000 v2.1) which worked great right out of the box. A couple months later I tried to setup a home network so that my two laptops could access a shared drive on my wired desktop, but for some reason they didn't show up as being on the same network. All computers involved are running Windows 7 if that matters.
Upon a recommendation from I friend I put DD-WRT on the router and it worked fine. Setup MAC filtering and WPA2 Personal security. This worked fine for about 4 months until today.
When I got home from work today I noticed my laptop wouldn't pull up any web pages, but it said it was connected. Then I noticed my iPhone wasn't connected either. I restarted my laptop and then it wouldn't connect to the wireless either (I could see the wireless, but I would get a Could not Connect error when I tried to connect to it).
I went to my desktop and it is working just fine, it is plugged into the back of the router. I also have an AT&T MicroCell (cell phone booster) that is plugged in to the back of the router and it works fine too.
I removed the encryption and MAC filtering. I then reset to factory (or "factory" DD-WRT) and now the wireless works, but it is MUCH slower than my desktop. I ran a speedtest on my desktop and got 12 Mbps down and 1 Mbps up. On my laptop, I get 0.03 Mbps down and 0.25 Mbps up.
I am running Ubuntu 10.04 on my Acer Aspire One netbook.The wireless connection works great, but the wired is totally dead.
When I plug the Ethernet wire, the little led next to the port doesn't blink.
If I do ifconfig, this is the output:
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1659 errors:0 dropped:0 overruns:0 frame:0
TX packets:1659 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
[code]....
There is no eth0. Is that normal?
In the "Network Connections" GUI there is an entry "Wired connection 1", its "MAC address" field is blank.
How can I make the wired connection work?
Wired Internet works on laptop but not on desktop 1) Cable modem --> Switch --> Wireless Router --> ATA Adapter for the VOIP Phone --> Desktop Worked until i had a minor power outage. After which everything stopped ie No internet. So i tried scenario 2.
2) Cable modem --> Wireless Router --> Switch --> ATA Adapter for the VOIP Phone --> Desktop Got internet working (wired and wireless) for few days and then it stopped suddenly again. I tried both the above scenariosn again, but didnt work.
3) Now I connected my laptop (which i connected via wireless only before) with wire from cable modem straight to Laptop. Interent works
4) When I connect the same wire used successfully on laptop to my desktop, internet doesnt work. Both Laptop and desktop have windows 7?
Acer Aspire 4520 Wireless network no longer works.
The light on keyboard is lit up but when pressed, it says No Device.
Went out a long time ago and I quit using the laptop. Borrowed external adapter which works.
No updates found for driver.
I have two PCs hooked up to the same router, a BEFSR41. Both connect to the internet fine. One can access the router setup/admin page fine. On the other one, though, the router asks for a user name and p/w, but the setup screen never loads. I get the eternal "Loading" message but it never gets there.
[code]....
Model wrt54gsWindows xpI got the wireless network setup and password protected and my computer and phone can sign o the wireless network, but when I try to go to a website it doesn't work. If I connect te computer directly to the modem then it works.
View 2 Replies View RelatedRegion : Poland
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP :
I have a problem with files sharing via wi-fi. I can not share files over the network using wi-fi connections. While the network is the cable connection sharing is available. The network also acts as one computer is connected by a cable to the router and the other via wifi. But if the two computers are working through wifi network does not work. Are there any settings in the router, which can cause blocking calls via wifi?
I'm trying map the USB hard drive connected to my EA4500 router as a network drive in Windows 7, and it works perfectly until I enable secure folder access on the router.
After enabling secure folder access, and not changing any other settings on the router I first unmount the drive since it was set up without credentials and doesn't work that way any more. When I try to remap the drive I use the same address, but select "Connect using different credentials" When it prompts me for the log in info I try using the router admin account, but it fails to connect. Windows network diagnostics tells me the device refused the connection. I proceeded to set up an account on the router under the folder access settings with the same username, and password I use on my computer, and tried to connect it without checking "Connect using different credentials" (And typing them in manually if that matters) with the same results.
Even with secure folder access enabled I can still reach the drive just fine by typing "ftp://192.168.1.1/" into file explorer. It prompts me for a username and password, I put in the admin credentials, and I'm in. Even the account I created with the same username/password as my computer works this way.
After disabling secure folder access everything works perfectly fine again... I would MUCH rather do this with it though.
Following these directions: [URL] When clicking the browse button the router shows up when secure folder access is disabled, but does not after it is enabled. I've looked through my windows sharing settings, and haven't noticed anything that should cause problems, pretty much everything is enabled. I've also tried turning off my firewall with no success.
My provider is Time Warner and I have their Wideband 50 MBs. This requires me to have a Motorola Surfboard router/modem (so no stand alone modem)
1. No applications such as google talk, steam, my ftp client or basically any computer application that requires internet for some of its functions. (all on my desktop PC connected to LAN)
2. The internet would partially work. I could get to some websites but it would often fail to load
3. Other computers are able to connect to the LAN and it work without an issue
Has anybody read The Illustrated Network: How TCP/IP Works in a Modern Network by Walter Goralski? url...I was thinking about picking it up. Does it offer anything new to a student studying for his CCNP?
View 9 Replies View RelatedConnecting with a LAN cable to the router works 100%, and I can get access to the router's IP-address, but when trying to connect to wireless, it asks for the WPA key, and I fill it in, but then gives an error saying "Can't connect to wireless network: *network name here*" (This is translated from Dutch to English, so it might be a bit different on an English computer).
View 3 Replies View RelatedHow Stuff Works "How Network Address Translation Works"."This is where NAT (RFC 1631) comes to the rescue. Network Address Translation allows a single device, such as a router, to act as an agent between the Internet (or "public network") and a local (or "private") network. This means that only a single, unique IP address is required to represent an entire group of computers." so let's say 6-7 pc's can have access to the internet using the same IP. doesn't this causes any problems? what if one of those pc's was used fore doing something illegal? how can they spot it later on? or what if 2 or more pc's access (from that subnetwork) access the same website with the same IP?
View 3 Replies View RelatedI have Windows 7 PRO and since I bought it I have wierd disconnects. The network works for like 2-3 minutes and then disconnects for 5+ mintues.
View 5 Replies View Relatedi am pretty good with computers but this problems got me stumped, my old desktop dell deminsions 4400 will not connect to my home network. So I first reinstalled the driver and plugged the wire in and like magic i had internet. so i took it up stairs, no internet connection. so i whipped out my handy dandy laptop and plug the wire into the cat5 port and i had internet. so this is telling me the wires in my walls are working, my router and modem are working, and my pc is doing something crazy when it changes elevation. I'm about to take it downstairs to see if itll work again
View 2 Replies View RelatedI have a HP G60-530US and i use Mozilla Firefox. My computer had froze up and i had to restart it. My wifi is working but it keeps sending me firefox cant find the server at... message. It said that the firewall or proxy could be doing it but i cant find a problem with it. My computer had just updated so i dont know if that could be the issue. My other computer is working just fine so i know its not the router. My computer has done with before but i cant remember how i fix it and if im not mistaken my computer had updated when it happen the last time, but im not 100% sure.
View 3 Replies View RelatedWindows XP Wireless works slow.
View 2 Replies View RelatedWhen I use my desktop wired to my broadband I can access any site on the Internet. Yet whenever I use the wireless either on my laptop, iPad or a net book I can only access some sites!
View 2 Replies View RelatedI have a Netcomm NB9WMAXXn router and 3 laptops i want to connect to it wirelesslyThe problem is that the iwreless internet connection slows down and eventually drops out after about 30m unless one of the laptops remains connected via Ethernet to the router. The wireless laptops will remain connected to the router but the internet connection will fail. The laptop with Ethernet connection retains a very good connection so i'm thinking this is an issue with my router or it's configuration
View 1 Replies View RelatedMy WiFi works fine on phones, tablets, and my xbox. The only problem is that it is extremely slow on my two laptops.
View 5 Replies View RelatedWhile im playing games like battefield 3 left 4 dead 2 or minecraft i get rubberbanding lag which is basically my game character running foward then being shot back to his original postion. I originally was using a wireless usb adapter so i blamed it for the cause of the lag. (My pings were fine btw) I went to ethernet for a week and the lag went away so everything is fine via ethernet. I just bought a new wireless card but there is still this terrible lag!
View 10 Replies View Relatedi have two lap top and would like my wife to use one while i use the other at the same time.
View 1 Replies View RelatedI have a Gateway desktop computer easily connected to an internet providing modem from Comcast. I have tried to set up a wireless router so that I can connect my Sony laptop, but have not succeeded. The laptop has a built in wireless device that easily connects to other wireless routers such as the one in my parent's house or my sister's house, just not the one in my own place.Connecting the laptop to the wireless router seems to be accomplished. The laptop says it has been connected and signal strength is "very good" but web browsers are unable to connect to the internet. I have tried three separate web browsers (firefox, internet explorer, and google chrome) and still nothing.The router seems to be working fine. It is a netgear N150. Power is on and the desktop, connected through the router, and then into the modem, connects just fine. This tells me internet connection is alright through the modem, right? I have tried numerous times to turn off the power and wait, then try connecting again and have not succeeded. I have done this at both the modem and the router.
I have gone into the laptop's ip settings and have marked the ip and dns addresses to automatically receive. I believe a great deal of the problem is that the laptop is not receiving any wireless bytes being sent out. I've seen the sent bytes between 84 and 378 (is this low?) but nothing is received. If I could figure this part out I feel I'd know what's wrong. The IPv4 IP address is 192.168.1.3The IPv4 Subnet mask is 255.255.255.0The IPv4 default gateway is 192.168.1.1The ipv4 DHCP server and DNS server read the same number as the default gateway.Not that I know much about these numbers. Every time the problem is encountered I strike the "diagnose" tab but to no avail, as though the laptop refuses to even try to diagnose. I have attempted to get new IP settings and reset the network adapter but the laptop, and though I receive a "repairi
It pretty much just stopped working one day. I have reset my router completely. I have tried the netsh commands. I have tried using different dns ip addresses. I have released and renewed ipconfig. I have reset both my cable modem and my wireless router. I have uninstalled and reinstalled the wireless drivers and made sure they were up to date. None of these things worked.
Here is the story. My laptop will not connect to the internet even though it says it is connected and shows the SSID when you hover over the wireless on the bottom. I have an iPad, iPhone, and another laptop connected to this exact wireless connection. The laptop that does not connect (the one i am having problems with) recently connected to another home wireless network this past weekend in another house so it is not the card in the laptop. It seems to be settings in this particular laptop with just this wireless connection as the wired connection using the same router works just fine. It DOES NOT time out when I ping websites in the command prompt. I get returned values. I have tried several browsers and none of them work. It will not connect to AIM either. I have spent many hours trying to figure out what the hell has changed and why this connection won't work. I really need this connection for work.
PS - Running Windows 7 with a Netgear Wireless G router - WPA security
My laptops internet connection quality is inconsistent. I constantly have to disconnect and reconnect my LAN connection to speed things up or keep things going. Then one day I discovered that if I keep the computer plugged in, the internet works consistently and just fine, but ONLY if I do this
View 3 Replies View Related