Wireless Works Wired Does Not After Installing New Router
Feb 3, 2013
Intalled a new router (Linksys Cloud 1200) yesterday. Immediately after that the 2 computers that were connected to the network could no longer access the internet. My laptop and my ipad can access the internet wirelessly. The laptop which was not connected to the network when I connected the router can access the network both wirelessly and wired. Printers attached to the network will print without a problem.Finally I took an old computer out of storage (running WinXP) and hooked it up to the wired network. It too has no problems accessing the network. So have to assume the issue is a software issue with the two computers that were hooked up to the network when I changed the router.I have read the posts here - I did a stack reset on one of the computers but no luck. I removed Norton 360 and Team Viewer which in other posts people said they had issues with...to no avail.
Since I dont have a wireless connection to the 2 computers that cannot access the internet - I cannot download TSG SysInfo. However here I did copy the ipconfig lines below from the desktop thats not responding. [code] Was working fine until I replaced the router. I tried going back to the oldrouter (Netgear) same issue - no wired internet connectivity.
View 1 Replies
ADVERTISEMENT
Dec 25, 2011
I'm trying to set up a wireless network for my parents. I have a Belkin Play N600 router (model F7D8302) that I'm trying to hook up to an Acer desktop running Vista. The modem is a Siemens Speed stream 4100. I have a cable going from the ethernet port of the modem to the modem port on the router. The pc is connected to one of the other four ports in the router. The wireless works fine, but I can't get the wired connection on the desktop working. The Internet light on the modem is not on, but the modem works fine when connected directly to the pc. I've tried power cycling and resetting everything, but it's still not working.
View 9 Replies
View Related
Nov 17, 2011
I have a Cisco linksys router e1550. My wireless network is working fine, but my wired (PC) is not working?
Removing the router and having the modem connected to my PC works but when I put on my router my wired connection only works for a few seconds to none
So I think the router may be causing it, could it be the settings? Even though there at default.
View 1 Replies
View Related
Nov 16, 2011
About 6 months ago I bought a new router (Linksys E1000 v2.1) which worked great right out of the box. A couple months later I tried to setup a home network so that my two laptops could access a shared drive on my wired desktop, but for some reason they didn't show up as being on the same network. All computers involved are running Windows 7 if that matters.
Upon a recommendation from I friend I put DD-WRT on the router and it worked fine. Setup MAC filtering and WPA2 Personal security. This worked fine for about 4 months until today.
When I got home from work today I noticed my laptop wouldn't pull up any web pages, but it said it was connected. Then I noticed my iPhone wasn't connected either. I restarted my laptop and then it wouldn't connect to the wireless either (I could see the wireless, but I would get a Could not Connect error when I tried to connect to it).
I went to my desktop and it is working just fine, it is plugged into the back of the router. I also have an AT&T MicroCell (cell phone booster) that is plugged in to the back of the router and it works fine too.
I removed the encryption and MAC filtering. I then reset to factory (or "factory" DD-WRT) and now the wireless works, but it is MUCH slower than my desktop. I ran a speedtest on my desktop and got 12 Mbps down and 1 Mbps up. On my laptop, I get 0.03 Mbps down and 0.25 Mbps up.
View 4 Replies
View Related
Apr 6, 2011
this computer was working on this router no problem. computer crashed and noiw computer is fine i connected it to my cable from ny desk top comutyer and works fine. It just cannot hook up to the wireless connection?
View 1 Replies
View Related
Mar 15, 2011
Does it support SSL VPN? As I would like to have secure web access without installing other software.
View 1 Replies
View Related
Jan 25, 2011
MY ISP is AT&T. I have their Westell DSL modem, with a bridged connection to a Linksys wireless router. The router is connected via ethernet to a dead computer: a 7 year-old Dell desktop that will boot up but shut down right away. I have been able to connect multiple laptops wirelessly to this network. I thought an ethernet connection was required in a home network such as mine? The cable has been plugged into a dead computer for several months and frankly I'd like to get rid of the desktop. What exactly is the ethernet requirement - just to be plugged into a port? Could I theoretically just yank the ethernet card out of the desktop and use it instead of the whole dead system?
View 5 Replies
View Related
Nov 5, 2009
I have two PCs hooked up to the same router, a BEFSR41. Both connect to the internet fine. One can access the router setup/admin page fine. On the other one, though, the router asks for a user name and p/w, but the setup screen never loads. I get the eternal "Loading" message but it never gets there.
[code]....
View 8 Replies
View Related
Nov 9, 2011
I have a brand new broadband service in my new house.The problem I have and the ISP support cannot understand is that using my laptop in i connect wirelessly to internet as soon as i request a page the router losing connection to the internet.But I can use my smartphone wirelessly that does not cause router any problems.If I use the lan cable the internet is fine and only disconnects every now and again.
View 1 Replies
View Related
Jun 11, 2012
My computer not working probably with a wired connection.I can ping to the problem sites with absolutely no issues.
View 3 Replies
View Related
Apr 20, 2013
problem started a few months ago. wireless kept crashing. tracked it down to seeing it crash when certain Win7 Dell laptop tried to connect. (Laptop is company owned with standard type of corporate AD authentication and image) my wireless setting use WPA2 personal with AES encryption. use both N & G, auto rate and scan.any time this laptop connected the wireless crashed, other devices didn't show SSID (both main and guest)But wired connection continued to work fine.
View 1 Replies
View Related
Dec 9, 2011
I have my internet hooked up to a DSL Modem and a Wireless Router. But I had configured the Wireless Router wrong that I couldn't connect to it using a WiFi. I was going to reconfigure it but the Netgear Router was outdated that their reconfiguring URL no longer existed. So I went out and got a *NEW* Netgear Router. Prior to the *NEW* Router I had a Laptop and a PC connected via DSL Cable connected in the Wireless Router. Now with the *NEW* Router I had just purchased I connected everything just like I had done with my previous Router. Wireless Connect works great but I can't connected using the DSL Cable connection. It does not respond. I tried connecting the cables to different ports but it didn't work. My PC mainly needs the wired connection cuz it's where I play my Online games. I tried playing with my Wireless connect but it lags very bad. How to get the wired connections to work? Netgear N600 Wireless and Dual Band Router
View 3 Replies
View Related
Mar 18, 2012
I am running Ubuntu 10.04 on my Acer Aspire One netbook.The wireless connection works great, but the wired is totally dead.
When I plug the Ethernet wire, the little led next to the port doesn't blink.
If I do ifconfig, this is the output:
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1659 errors:0 dropped:0 overruns:0 frame:0
TX packets:1659 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
[code]....
There is no eth0. Is that normal?
In the "Network Connections" GUI there is an entry "Wired connection 1", its "MAC address" field is blank.
How can I make the wired connection work?
View 2 Replies
View Related
Jan 25, 2013
Wired Internet works on laptop but not on desktop 1) Cable modem --> Switch --> Wireless Router --> ATA Adapter for the VOIP Phone --> Desktop Worked until i had a minor power outage. After which everything stopped ie No internet. So i tried scenario 2.
2) Cable modem --> Wireless Router --> Switch --> ATA Adapter for the VOIP Phone --> Desktop Got internet working (wired and wireless) for few days and then it stopped suddenly again. I tried both the above scenariosn again, but didnt work.
3) Now I connected my laptop (which i connected via wireless only before) with wire from cable modem straight to Laptop. Interent works
4) When I connect the same wire used successfully on laptop to my desktop, internet doesnt work. Both Laptop and desktop have windows 7?
View 2 Replies
View Related
Nov 24, 2011
I have a buddy who owns a bar and wants to install a insecure wireless router for his customers downstream from his SBC Global ATT Modem/Wireless Router combo.
-Modem/Router Combo: Actiontec GT724WG
-Downstream Unsecure Wireless Router: D-Link DIR-651
He says has 3 static ips for the modem, and 1 of the network cables coming from the modem directly into the D-Link Router. I first attempted to just plug it into the uplink, and let DCHP do its magic, but I had no luck with that. I could connect to the router but it didn't have internet.
So I restarted the downstream router, and plugged the network cable into the 1st port, and suddenly I had internet on the wireless but it would constantly go up and down, and ping times were extreme erratic.
View 8 Replies
View Related
Sep 4, 2011
I am trying to instal my Netgear router. It is asking for the Preferred DNS name and the alternate DNS name? I got the IP address and the other required fields but I'm not sure about eh DNS thing?
View 2 Replies
View Related
Mar 27, 2012
I recently had to reformat, and I tried to re-install my E1000 Wireless N router from the CD. Even after entering my network name and password, it said it was unable to connect to my network. My internet works fine - I just can't make my computer in control of it again. I have several devices connected wirelessly, including an Ipad, and they all get internet fine. how to get the program installed so I can change settings again?
View 1 Replies
View Related
Jan 10, 2013
getting ready to do the install of a EA4500 with a Cable internet provider. I found the site on Cisco on how to manually install the router with Cable [URL]It advises to first install using the software that comes with the router.It then gives the following steps:
Step 1:Access the router’s web-based setup page. For instructions, click here.NOTE: If you are using a Mac computer to access the router’s web-based setup page, click here.
Step 2:On the Setup tab, click the MAC Address Clone sub-tab.Step 2:Check the Internet IP Address. If it has numbers, this means the router has been properly configured.
NOTE: If the Internet IP Address values are showing up 0.0.0.0, click on Release IP Address then the Renew IP Address buttons.NOTE: For wireless-B and wireless-G routers, click on the DHCP Release and DHCP Renew buttons. MY QUESTION: are the steps above something that definately will need to be done or is that in the case that it's not configured via the installation using the software?I have this same router installed at my home however I use DSL internet and my daughter uses Cable internet so I want to make sure I am positive on the steps prior to installing.
View 2 Replies
View Related
Jul 28, 2011
I just got a new E4200 router and downloaded Cisco Connect from the web site...file name CiscoConnect.E4200.1.4.11160.2.exe. When I try to run it, I find through Task Manager that Setup.exe is using about 35 to 40% CPU, but I'm never even getting to anything on the screen, nor is Task Manager even showing it as a running application. I'm running Windows XP SP3 (latest updates). I tuned off the AVG virus scan. But it still just seems to hang. BTW, I used the web interface to fully configure the router and it works fine so I could get by without Cisco Connect, but it might just be easier to use.
View 4 Replies
View Related
Jul 14, 2009
Started a fresh installation on windows 7 RC 64 bit popped in adapter, and tried installing disk, disk would get the portion where it asked to input the adapter, then just vanish after i click next. I restarted, nothing. I clicked set up again, says drivers are already installed....though there is no app to show profiles, im guessing it isn't.
[URL]
version 1.00 would work just like the disk. version 2.00 would not start at all and would give an "the application was unable to start correctly (0x0000005).."
View 4 Replies
View Related
Sep 14, 2011
Can I septup an OpenVPN in an E4200 without installing dd-wrt?
View 7 Replies
View Related
Oct 28, 2008
Since installing my WRT160N my printers have stopped working. All printer drivers have been removed including acrobat and my fax.
Even if I try reinstalling my drivers, I get the following error: Spooler SubSystem App has encountered a problem and needs to close.
Prior to this error my firewall was giving me constant warnings about Pure Networks Admin assistant application trying to access the same files(i.e. nmctxth.exe). Even though I allowed it still kept popping up.
I am using the online armor firewall on a Windows XP system. I cannot access the LinkSys Advisor anymore as it will not start.
View 4 Replies
View Related
Aug 14, 2012
I have a Linksys E2000 router. I am trying to install an Epson NX230 printer on my home network. Apparently, the Epson printer has a MAC address assigned to it. My network cannot find the printer. I looked at my riuter setup and the MAC Address Clone has two buttons, Enabled Disabled. The Disabled button is clicked on. Accdording to documentation I foudn on this website, it looks like I can Enabled the MAC Address clone button. The document also mentgioend entereding the MAC address for a PC.
If I enable the MAC Address Clone, do I enter the MAC address for the printer or during the install process does the MAC address get installed also
View 9 Replies
View Related
Jun 2, 2012
I have the latest firmware, have the settings correct (the UPnP is disabled and whatever)
Model number: E3000
Serial number: CVQ01KC13100
Firmware version: 1.0.04 build 6
Operating system: Windows 7 SP 1
Software version: 1.3.11006.1
Connection type (WAN): PPPoE
Went out of town 2 weeks in March, and all through April didn't have any disconnects. Have had this problem since I got it, it gets really bad from time to time (like now). Thought it was my provider for the longest time, but found out if I connect via wired, no disconnects! Is re-flash simply downloading and installing firmware?
View 6 Replies
View Related
Dec 28, 2008
I am trying to install my router but I keep getting the error message that my ethernet cables are not connected. I have tried several times and everytime I know that the cables are in correctly. Is there anyway to solve this problem?
I am running in XP and my router is WRT54G2.
View 5 Replies
View Related
Jul 28, 2012
I own the linksys wrt160n v2...It has latest firmware 2.03 build 9...After installing this firmware i have noticed the internet speeds have reduced,the router requires frequent reboots to make it stable..
i used to have firmware version 2.02 build 15...It was stable unlike the current firmware...i cant find the old firmware anywhere...how do i revert back to old firmware?
All settings are currently at default.
View 3 Replies
View Related
Mar 16, 2011
I have a Gateway desktop computer easily connected to an internet providing modem from Comcast. I have tried to set up a wireless router so that I can connect my Sony laptop, but have not succeeded. The laptop has a built in wireless device that easily connects to other wireless routers such as the one in my parent's house or my sister's house, just not the one in my own place.Connecting the laptop to the wireless router seems to be accomplished. The laptop says it has been connected and signal strength is "very good" but web browsers are unable to connect to the internet. I have tried three separate web browsers (firefox, internet explorer, and google chrome) and still nothing.The router seems to be working fine. It is a netgear N150. Power is on and the desktop, connected through the router, and then into the modem, connects just fine. This tells me internet connection is alright through the modem, right? I have tried numerous times to turn off the power and wait, then try connecting again and have not succeeded. I have done this at both the modem and the router.
I have gone into the laptop's ip settings and have marked the ip and dns addresses to automatically receive. I believe a great deal of the problem is that the laptop is not receiving any wireless bytes being sent out. I've seen the sent bytes between 84 and 378 (is this low?) but nothing is received. If I could figure this part out I feel I'd know what's wrong. The IPv4 IP address is 192.168.1.3The IPv4 Subnet mask is 255.255.255.0The IPv4 default gateway is 192.168.1.1The ipv4 DHCP server and DNS server read the same number as the default gateway.Not that I know much about these numbers. Every time the problem is encountered I strike the "diagnose" tab but to no avail, as though the laptop refuses to even try to diagnose. I have attempted to get new IP settings and reset the network adapter but the laptop, and though I receive a "repairi
View 12 Replies
View Related
Jan 21, 2013
I can follow directions and am fairly tech-savvy, just don't have the time to troubleshoot this stuff and run my business. Here's the rundown:Router:Cisco Linksys E1000 V2
-working fine until I unplugged to move it and plugged it in
-verified with tech support the problem is not physical
-right now, am hardwired to the router, which is hardwired to the cable modem, and connectivity is fine through hardwiring
-no luck through wireless - this is the error message I get:
This webpage is not available:The server at www.google.com can't be found, because the DNS lookup failed. DNS is the network service that translates a website's name to its Internet address. This error is most often caused by having no connection to the Internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing Google Chrome from accessing the network.
View 9 Replies
View Related
Jun 9, 2012
Our home school's having trouble attaching a wireless router to my XP PC's ethernet port.Our donated vintage Macs and XP machines are tied to the internet via a cable box's wireless router. Works just fine. Now I wish to boost the signal to a building beyond the local area by attaching a wireless router to a Dell 260 running XP. This router's IP is 192.168.11.1 (ON) and 192.168.11.100 (OFF), and I've spent hours with the Connection Wizard thing on XP trying to create a ethernet path to the router but I can't find a configuration that states an ethernet path or channel. The modem lights normally and other machines can pick up and connect with its signal but there's no real transmission, the receiver machines getting:Firefox can't find the server at [URL].Check the address for typing errors such as [URL]instead of [URL] If you are unable to load any pages, check your computer's network connection.If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web.Ironically, the router works just great on the Macs, which has both Airport on to receive signals from a cable TV wireless router and also has its shared Ethernet connection on, and the ethernet side requires no IP configuration like it seems you must on the XP's internet connection page. The router in question just plugs in the Mac and transmits just fine. I would use the Mac for this purpose but I really wish to use the Dell.The Dell's current network configuration after many trials:
Wireless Connection 3
LAN / High Speed Internet
Connected, Firewalled
802.11n USB Wireless LAN Card
IP 169.18.2.7
[code]....
Oddly, the Mac's Network panel states: "The cable for built-in ethernet is connected, but your computer does not have an IP address and cannot connect the internet." Yet it does!
View 6 Replies
View Related
Aug 11, 2011
Since the blackout beginning of this week from dlink I had to reset my camera totally to operate it again. works now again with iphone and with mydlink. But it only works as long it is connected via lan cable to my router. I accessed the set up (via ipaddress) and entered the router details to the setup but as soon I disconnect from lan it does not work anymore. What did I oversee.
MAC OS X
Airport extreme
View 1 Replies
View Related
Dec 30, 2012
Mac airport shows full bars in network connnection and green connected dot, but no access to internet. Ethernet connection works fine. I also couldnt connect with my Iphone.
I have Charter cable with Motorolla SB6121 modem. I've reset the modem, rebooted everything, cloned my ip address, all several times .......but still no go.
Linksys says they don't support this router anymore accept for a pay for support service, which I would like to avoid.
View 5 Replies
View Related
Sep 29, 2011
If I step outside the office in my house where the router is hardwired to my desktop, I still see there is a strong signal but no device is able to connect to the internet wirelessly. I can connect with my laptop or my iPhone from inside the office.I spent a couple hours and some dollars with the Cisco tech people and all they could tell me is - must be a hardware problem and it's not under warranty.They dialed in remotely so I know the setup is right.This has been going on for months.
View 3 Replies
View Related
Nov 28, 2012
I have a win7 desktop upstairs with all of my media on it.I also have a winXP laptop that I would like to use as a media center running xbmc connected to my tv downstairs.I have set up a workgroup so my laptop can access the media stored on my desktop and everything works great when they are both hardwired to my router (Linksys E3000).However, as soon as I unplug my laptop from my router and switch to the wireless connection I can no longer ping my desktop or access the shared folder (internet still works fine on the laptop, it just cant see my desktop anymore).If I plug it back in to the router, everything works again.
The exact error message I get when I try to access the shared folder is "\INFINITYMedia is not accessable. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. [code]
View 14 Replies
View Related
