Linksys Wireless Router :: Installing E1000 From CD After Reformat?
Mar 27, 2012
I recently had to reformat, and I tried to re-install my E1000 Wireless N router from the CD. Even after entering my network name and password, it said it was unable to connect to my network. My internet works fine - I just can't make my computer in control of it again. I have several devices connected wirelessly, including an Ipad, and they all get internet fine. how to get the program installed so I can change settings again?
View 1 Replies
ADVERTISEMENT
Jan 10, 2013
getting ready to do the install of a EA4500 with a Cable internet provider. I found the site on Cisco on how to manually install the router with Cable [URL]It advises to first install using the software that comes with the router.It then gives the following steps:
Step 1:Access the router’s web-based setup page. For instructions, click here.NOTE: If you are using a Mac computer to access the router’s web-based setup page, click here.
Step 2:On the Setup tab, click the MAC Address Clone sub-tab.Step 2:Check the Internet IP Address. If it has numbers, this means the router has been properly configured.
NOTE: If the Internet IP Address values are showing up 0.0.0.0, click on Release IP Address then the Renew IP Address buttons.NOTE: For wireless-B and wireless-G routers, click on the DHCP Release and DHCP Renew buttons. MY QUESTION: are the steps above something that definately will need to be done or is that in the case that it's not configured via the installation using the software?I have this same router installed at my home however I use DSL internet and my daughter uses Cable internet so I want to make sure I am positive on the steps prior to installing.
View 2 Replies
View Related
Jul 28, 2011
I just got a new E4200 router and downloaded Cisco Connect from the web site...file name CiscoConnect.E4200.1.4.11160.2.exe. When I try to run it, I find through Task Manager that Setup.exe is using about 35 to 40% CPU, but I'm never even getting to anything on the screen, nor is Task Manager even showing it as a running application. I'm running Windows XP SP3 (latest updates). I tuned off the AVG virus scan. But it still just seems to hang. BTW, I used the web interface to fully configure the router and it works fine so I could get by without Cisco Connect, but it might just be easier to use.
View 4 Replies
View Related
Jul 14, 2009
Started a fresh installation on windows 7 RC 64 bit popped in adapter, and tried installing disk, disk would get the portion where it asked to input the adapter, then just vanish after i click next. I restarted, nothing. I clicked set up again, says drivers are already installed....though there is no app to show profiles, im guessing it isn't.
[URL]
version 1.00 would work just like the disk. version 2.00 would not start at all and would give an "the application was unable to start correctly (0x0000005).."
View 4 Replies
View Related
Sep 14, 2011
Can I septup an OpenVPN in an E4200 without installing dd-wrt?
View 7 Replies
View Related
Oct 28, 2008
Since installing my WRT160N my printers have stopped working. All printer drivers have been removed including acrobat and my fax.
Even if I try reinstalling my drivers, I get the following error: Spooler SubSystem App has encountered a problem and needs to close.
Prior to this error my firewall was giving me constant warnings about Pure Networks Admin assistant application trying to access the same files(i.e. nmctxth.exe). Even though I allowed it still kept popping up.
I am using the online armor firewall on a Windows XP system. I cannot access the LinkSys Advisor anymore as it will not start.
View 4 Replies
View Related
Aug 14, 2012
I have a Linksys E2000 router. I am trying to install an Epson NX230 printer on my home network. Apparently, the Epson printer has a MAC address assigned to it. My network cannot find the printer. I looked at my riuter setup and the MAC Address Clone has two buttons, Enabled Disabled. The Disabled button is clicked on. Accdording to documentation I foudn on this website, it looks like I can Enabled the MAC Address clone button. The document also mentgioend entereding the MAC address for a PC.
If I enable the MAC Address Clone, do I enter the MAC address for the printer or during the install process does the MAC address get installed also
View 9 Replies
View Related
Jun 2, 2012
I have the latest firmware, have the settings correct (the UPnP is disabled and whatever)
Model number: E3000
Serial number: CVQ01KC13100
Firmware version: 1.0.04 build 6
Operating system: Windows 7 SP 1
Software version: 1.3.11006.1
Connection type (WAN): PPPoE
Went out of town 2 weeks in March, and all through April didn't have any disconnects. Have had this problem since I got it, it gets really bad from time to time (like now). Thought it was my provider for the longest time, but found out if I connect via wired, no disconnects! Is re-flash simply downloading and installing firmware?
View 6 Replies
View Related
Dec 28, 2008
I am trying to install my router but I keep getting the error message that my ethernet cables are not connected. I have tried several times and everytime I know that the cables are in correctly. Is there anyway to solve this problem?
I am running in XP and my router is WRT54G2.
View 5 Replies
View Related
Mar 26, 2012
I own a E1000 router that I use with several wireless machines. Unfortunately, I cannot connect to the configuration of the router by typing url...in a browser, be it wireless or weirdly. For example, Firefox displays "Connection has been reinitialized". Furthermore, when I launch Cisco Connect, it only shows the error "Unable to connect to router". I tried to switch my router off and on, but that doesn't work. Totally resetting the router solves the problem, but not definitely.Is there a solution that does not require resetting my router?
View 2 Replies
View Related
Dec 20, 2011
My guest can't use my wireless network and I can not add more devices like a ipad2. Got a new ipad2 for my son for Christmas been trying to set it up for Christmas, so on Christmas day I am not trying to do the set up. My problem is I can not get it to log on to the network. I have been putting in the same pass word all my other computers in the house use but it will not work...
View 2 Replies
View Related
Feb 10, 2013
My wireless router (E1000) was accidentally unplugged. Since then the wireless LED light doesnt come on and the router cannot be detected. All the other lights are on. I tried to reset it but I dont think it worked, since the power LED didnt blink as its supposed to do after holding reset for 10-15 seconds (or more!!).
View 5 Replies
View Related
Aug 9, 2011
I've been using the E1000 for months. I have 2 iphones, an ipod, a windows 7 netbook and a macbook connected wirelessly to it. It's been set at wpa2/wpa mixed mode all this time without a problem. Out of the blue: no wireless connection on any device. I restarted the modem, router, PC's, phones, etc. I've updated the firmware. The only way I can get a wireless connection is to use wep. How can I get the better security and speed of wpa2 back?
View 4 Replies
View Related
Feb 21, 2012
I am trying to access the internet with my ipod and it is picking up my wireless connection but it is asking for a password, how do I get my password. I don't remember seeing a password when I hooked up my router several months ago. I called Cisco for some technical support but they wanted money to get me and I am not paying them a dime.
View 1 Replies
View Related
Jul 3, 2012
I can setup my router with the cd
View 1 Replies
View Related
Jul 26, 2010
I have a PS3, and i play allot of video games such as all COD game especially MW2. It says i have a strict or moderate NAT. My router is in the same room as the PS3, so i should have a Open Nat.Also i have another question, i bought this Epson printer from Best Buy, i was wondering if I can connect to it Wireless, but i think i cant connect to it wireless cause i dont see the WiFi Certification on the printer or anything hints that it can connect wireless
View 9 Replies
View Related
Sep 3, 2011
With the E1000 tthe wireless devices they seem to work just fine, I can access the internet just fine.
For my desktop PC in oder to use the router to get on the internet or to even use the Cisco Connect to check the router, the E1000 needs to be rebooted. I am unable to access the router otherwise. I have tried 3 different LAN cards all with the same results.
The latest firmware notes do not look like upgrading the firmware will work. My Router info from Cisco connect
Model name: Linksys E1000
Model number: E1000
Serial number: CVN21L422937
Firmware version: 2.1.01 build 5
Operating system: Windows 7 SP 1
Software version: 1.3.11006.1
Connection type (WAN): unknown
View 1 Replies
View Related
Jan 24, 2013
Things seem to slow down significantly to the point of loosing connectiviety. When I check, my mips are 150 or so. Tried disconnecting and connecting again but didn't work. When I power down the router and power it up, I get 300 mps again but doesn't last too long
View 2 Replies
View Related
Dec 30, 2011
A lady gave me E1000 along with an IMB Thinkpad because her husband was the main user on the internet. I have an intel iMac 10.4.11, DSL. I have not yet connected to either device via the router. I am new to wireless routers. I have been to the configuration page
View 2 Replies
View Related
Apr 7, 2013
I have a Linksys E1000 router which was working fine. My hard drive crashed; I replaced the hard drive and now my router is not recognized. I have reset it and tried to reinstall it with the CD. Nothing works.
View 1 Replies
View Related
Jun 23, 2011
I had an E1000 for a couple of years that worked OK. Then it went nuts--sporadically dropped the signal, wouldn't show its web page, etc.--maybe a power surge, who knows? So I tossed it and got a new one on the theory that it would be a plug in replacement .The new unit had a good signal, but also wouldn't show its web page, so I couldn't configure security. I removed Network Magic and everything else I could see pertaining to the old unit. However, the CD for the new unit still gives me: " Your router has already been set up. You need to use an Easy Setup Key that you can use to get other computers connected." Needless to say, I don't have such a thing. Cisco Connect is not installed at this point, so I can't go into it to create one.How can I purge the remains of the old unit so the new one will install properly?
View 6 Replies
View Related
Jul 14, 2011
I have E4200 connected to Internet. It is configured with NAT. My side of the router is set to 10.10.10.0 and DFG is set to 10.10.10.254. Server is connected at 10.10.10.1 and is DHCP host.I now have E1000 that I want to connect downstream side of the E4200 (located on the other side of the building). I want the E1000 to be an extension of the existing network so the whole building looks like one network. I'm not sure how to configure the E1000. I assume I need to disable NAT but I'm not sure how to configure the Internet IP addresses of the router and nro am I sure how to configure the local network side of the router.As I write this, I wonder if I connect one of the Ethernet ports of the E1000 to the E4200 and just leave the Internet side unplugged?
View 2 Replies
View Related
Jun 10, 2010
I'm trying to set up my E1000 router and when I run the Cisco Connect software that came with the router I get a message that says that it can't find the router, I've tried running it with my computer connected to the router and not connected. I've looked through the FAQ section and didn't really find anything. I'm trying to set it up on a laptop, it's a Vaio running Windows 7, I don't if that makes any difference.
View 7 Replies
View Related
Nov 12, 2011
I am facing issue with my cisco wireless E1000, the wireless connection on the laptop reset on its own. Its like there is a timer and it reset's the wireless connection after some time. I was unable to measure the time after which it resets but its happening too frequently causing multiple internet apps to fail example if I am downloading something it will fail as the internet connection is reset. The firmware I am running on the rotuer is 2.0.01 and I have configured DHCP on the LAN, I am experiencing this problem with 3 laptop that I use at home which uses both G and N networks.
View 2 Replies
View Related
Feb 16, 2011
I've been searching off and on for the past couple months trying to figure out what we could do to our router to open our NAT, after having both the PS3 and Xbox 360 tell me I've got moderate NAT. I tried a DMZ with my PS3 having a static IP, I tried UPnP. I messed with firewall settings, to no avail.
I recently found something that did work however, on Google. Basically what happened was, I needed to reset the router and change a few settings on top of enabling UPnP I didn't know about(CTS Protection, remote management) how they could have anything to do with translation of data.
But like I said, after doing a huge step by step walk through, I was able to get open NAT in the network tests of both PS3 and 360(even though the PS3 obviously still says Type 2. It used to say Type 2, but it also used to have an error code at the bottom of the page). I've checked in games on each console, and they tell me I've got open NAT.
Now I still have one tiny problem. Red Dead Redemption. I play Red Dead Redemption online with two friends(who, incidentally, have the same router as me), and we haven't been able to communicate if we were using routers. We still can't, but I'm thinking that it's not my router anymore. I'm thinking his router has incorrect settings. Am I correct?
View 8 Replies
View Related
Jul 28, 2012
I own the linksys wrt160n v2...It has latest firmware 2.03 build 9...After installing this firmware i have noticed the internet speeds have reduced,the router requires frequent reboots to make it stable..
i used to have firmware version 2.02 build 15...It was stable unlike the current firmware...i cant find the old firmware anywhere...how do i revert back to old firmware?
All settings are currently at default.
View 3 Replies
View Related
Sep 21, 2011
So here is the issue:
When I connect my modem directly to my computer (modem > computer) it works just fine, internet connects and everything through the direct ethernet connection.But when I connect the modem to the router and then try to connect wireless with any other computer (modem > router > wireless) nothing works. Not even when I have it connected directly from the router to the ethernet on the main computer. (Which has ALWAYS worked until now.
View 1 Replies
View Related
Jun 30, 2011
my brand new Linksys E1000 wireless router. I am really struggling and cannot figure out what I am doing wrong.
I live in The Netherlands, have a modem (DSL I think...) and can connect wired through the modem with no problems.
I installed the E1000 with the CD, followed all the steps and my laptop is finding the network. However, it's only local, no internet and I don't understand why. Have tried to connect (wired) my computer to the E1000 and the E1000 to the modem but that doesn't work either.
View 2 Replies
View Related
Jan 28, 2012
However, my 13" Macbook (running Lion) sometimes finds if hard to connect after I turn it on. I will have to continously turn off and on the wifi of the macbook to have it force to look at wifi networks. It will not be able to see also other wifi networks which are present in my neighbors which my windows 7 and other machines can see. After playing around with it I found that the macbook will connect to wifi only after I connect it momentarily via cable. I do this everytime I turn on my macbook.I just upgraded to a Macbook Pro running on Lion and the same thing happened. I tried the same solution of connecting first via cable but to my disappointment, would not see any wifi network including my neighbor's which again the other machines can see. So I am stuck with using cable for now.
View 5 Replies
View Related
Jul 29, 2011
is there a way i can block a website from being viewed.i would like to do this from the setup page of my e1000 under website restrictions.
View 1 Replies
View Related
Apr 14, 2013
Lost password for router- how do I retrieve password.
View 2 Replies
View Related
May 31, 2012
where to find my guest user password
View 1 Replies
View Related
Feb 15, 2013
My e1000 was working fine until it was accidentally unplugged. Now it doesn't work. I downloaded the set up program from the site and tried to run it, but it does not recognize an internet connection when I have the modem connected to the router and the router connected to the PC. The internet works when I connect the modem directly to the PC. I have unplugged everything and restarted the PC several times and tried running the software again, but no dice.
View 4 Replies
View Related
