A lady gave me E1000 along with an IMB Thinkpad because her husband was the main user on the internet. I have an intel iMac 10.4.11, DSL. I have not yet connected to either device via the router. I am new to wireless routers. I have been to the configuration page
View 2 RepliesI can not get my password to work. The threads that I have read, requires a Ethernet cable to be connected but I have a wireless netgear card on the administrator PC how can I find the password to my E1000 router to verify and to change router settings
View 2 Replies View RelatedI bought a Linksys E1000 wireless router a year or so back. it was loaded onto a computer that no longer works. i have the router and the box but no disc or manual. My laptop and ipad are working fine with the router but i can't get my iphone hooked up and dont think i have the correct password. I dont have any software on my laptop to even figure it out. What can i do to get my phone to use the router?
View 1 Replies View RelatedI am about a level 4 maybe (10 being highest) when it comes to network configuration.I know what a router is, an IP addreess (external ones from ISP that is) and how to get around a little bit like how to access wireless config , edit properties on network connections and run ipconfig..My setup....I have a cable modem with 18mbs line...hooked into a Linksys E1000 wireless (N) router.From that I have 3 laptops setup (and a desktop thats never used).(none of whats next may be important but added it just in case)
Laptop a. is hardlined into wireless router (so I can edit config) and will be main machine it runs Vista
Laptop b. is connected to wirless connection from router and will main #2
Laptop c. is connected to wireless router
Desktop is connected to wireless router
(all others above run XP as OS)
My wife is running some webcam software that uses our internal IP address for its connection.It is no problem for her to connect her cam to the site with one laptop (any of the above) but when she tries to go to laptop b. and run another connection it says "You are currently broadcasting From This IP and cannot start another connection".
p.s. We have also tested bandwidth connection over and over on many sites (via browser) and it seems that when a cam is setup and the bandwidth is displayed what comes from / to the cam is WAYY slower than what we get in our tests...
1. I set a router admin password different from WiFi password(passphrase).
2. I run my Cisco Connect app and it asks me to change my router admin password.
If I don't change it - I can not use Cisco Connect app.
If I provide my WiFi password then it changes my router admin password.
Maybe it was done to have a "simple" solution - 1 password for everything. But maybe its a bug because router admin password should be different from WiFi password fro security reasons.
I am having a NAT issue with my two xboxes. The router is an e1000 v2.1 firmware 2.1.02. One xbox is wired into the router and the other has a wireless adapter. The wireless xbox gets open nat automatically, while the wired one's nat is strict. If i mess with DMZ and turn UPnP off i can get the wired to be open but the wireless one to be strict. Also port forwarding does not seem to work because only one or the other xboxes will get an open NAT. I do have the the correct ports in the port triggering section set to on but that does not seem like it works.
View 5 Replies View RelatedI have a E1000 N router and I was wondering if I can connect a G wireless adapter to it. I am trying to connect it with my Sanyo LED HDTV, it has the port for a USB but I can't seem to get it to connect. I've tried manually setting it up but I seem to have done it wrong. The reason for trying to connect to the television is Netflix. I learned that you can watch it instantly on your Tv, using the Blue-ray or a basic internet connection. The Blue-ray I currently have is not an acceptable brand, so I am trying the basic internet connection.
View 1 Replies View Relatedreset my Linksys E1000 and now I can't access wifi from my phone as neither my pw or my default ps work.
View 2 Replies View RelatedI own a E1000 router that I use with several wireless machines. Unfortunately, I cannot connect to the configuration of the router by typing url...in a browser, be it wireless or weirdly. For example, Firefox displays "Connection has been reinitialized". Furthermore, when I launch Cisco Connect, it only shows the error "Unable to connect to router". I tried to switch my router off and on, but that doesn't work. Totally resetting the router solves the problem, but not definitely.Is there a solution that does not require resetting my router?
View 2 Replies View RelatedMy guest can't use my wireless network and I can not add more devices like a ipad2. Got a new ipad2 for my son for Christmas been trying to set it up for Christmas, so on Christmas day I am not trying to do the set up. My problem is I can not get it to log on to the network. I have been putting in the same pass word all my other computers in the house use but it will not work...
View 2 Replies View RelatedMy wireless router (E1000) was accidentally unplugged. Since then the wireless LED light doesnt come on and the router cannot be detected. All the other lights are on. I tried to reset it but I dont think it worked, since the power LED didnt blink as its supposed to do after holding reset for 10-15 seconds (or more!!).
View 5 Replies View RelatedI've been using the E1000 for months. I have 2 iphones, an ipod, a windows 7 netbook and a macbook connected wirelessly to it. It's been set at wpa2/wpa mixed mode all this time without a problem. Out of the blue: no wireless connection on any device. I restarted the modem, router, PC's, phones, etc. I've updated the firmware. The only way I can get a wireless connection is to use wep. How can I get the better security and speed of wpa2 back?
View 4 Replies View RelatedI am trying to access the internet with my ipod and it is picking up my wireless connection but it is asking for a password, how do I get my password. I don't remember seeing a password when I hooked up my router several months ago. I called Cisco for some technical support but they wanted money to get me and I am not paying them a dime.
View 1 Replies View RelatedI can setup my router with the cd
View 1 Replies View RelatedI have a PS3, and i play allot of video games such as all COD game especially MW2. It says i have a strict or moderate NAT. My router is in the same room as the PS3, so i should have a Open Nat.Also i have another question, i bought this Epson printer from Best Buy, i was wondering if I can connect to it Wireless, but i think i cant connect to it wireless cause i dont see the WiFi Certification on the printer or anything hints that it can connect wireless
View 9 Replies View RelatedWith the E1000 tthe wireless devices they seem to work just fine, I can access the internet just fine.
For my desktop PC in oder to use the router to get on the internet or to even use the Cisco Connect to check the router, the E1000 needs to be rebooted. I am unable to access the router otherwise. I have tried 3 different LAN cards all with the same results.
The latest firmware notes do not look like upgrading the firmware will work. My Router info from Cisco connect
Model name: Linksys E1000
Model number: E1000
Serial number: CVN21L422937
Firmware version: 2.1.01 build 5
Operating system: Windows 7 SP 1
Software version: 1.3.11006.1
Connection type (WAN): unknown
Things seem to slow down significantly to the point of loosing connectiviety. When I check, my mips are 150 or so. Tried disconnecting and connecting again but didn't work. When I power down the router and power it up, I get 300 mps again but doesn't last too long
View 2 Replies View RelatedI have a Linksys E1000 router which was working fine. My hard drive crashed; I replaced the hard drive and now my router is not recognized. I have reset it and tried to reinstall it with the CD. Nothing works.
View 1 Replies View RelatedI had an E1000 for a couple of years that worked OK. Then it went nuts--sporadically dropped the signal, wouldn't show its web page, etc.--maybe a power surge, who knows? So I tossed it and got a new one on the theory that it would be a plug in replacement .The new unit had a good signal, but also wouldn't show its web page, so I couldn't configure security. I removed Network Magic and everything else I could see pertaining to the old unit. However, the CD for the new unit still gives me: " Your router has already been set up. You need to use an Easy Setup Key that you can use to get other computers connected." Needless to say, I don't have such a thing. Cisco Connect is not installed at this point, so I can't go into it to create one.How can I purge the remains of the old unit so the new one will install properly?
View 6 Replies View RelatedI have E4200 connected to Internet. It is configured with NAT. My side of the router is set to 10.10.10.0 and DFG is set to 10.10.10.254. Server is connected at 10.10.10.1 and is DHCP host.I now have E1000 that I want to connect downstream side of the E4200 (located on the other side of the building). I want the E1000 to be an extension of the existing network so the whole building looks like one network. I'm not sure how to configure the E1000. I assume I need to disable NAT but I'm not sure how to configure the Internet IP addresses of the router and nro am I sure how to configure the local network side of the router.As I write this, I wonder if I connect one of the Ethernet ports of the E1000 to the E4200 and just leave the Internet side unplugged?
View 2 Replies View RelatedI'm trying to set up my E1000 router and when I run the Cisco Connect software that came with the router I get a message that says that it can't find the router, I've tried running it with my computer connected to the router and not connected. I've looked through the FAQ section and didn't really find anything. I'm trying to set it up on a laptop, it's a Vaio running Windows 7, I don't if that makes any difference.
View 7 Replies View RelatedI am facing issue with my cisco wireless E1000, the wireless connection on the laptop reset on its own. Its like there is a timer and it reset's the wireless connection after some time. I was unable to measure the time after which it resets but its happening too frequently causing multiple internet apps to fail example if I am downloading something it will fail as the internet connection is reset. The firmware I am running on the rotuer is 2.0.01 and I have configured DHCP on the LAN, I am experiencing this problem with 3 laptop that I use at home which uses both G and N networks.
View 2 Replies View RelatedI've been searching off and on for the past couple months trying to figure out what we could do to our router to open our NAT, after having both the PS3 and Xbox 360 tell me I've got moderate NAT. I tried a DMZ with my PS3 having a static IP, I tried UPnP. I messed with firewall settings, to no avail.
I recently found something that did work however, on Google. Basically what happened was, I needed to reset the router and change a few settings on top of enabling UPnP I didn't know about(CTS Protection, remote management) how they could have anything to do with translation of data.
But like I said, after doing a huge step by step walk through, I was able to get open NAT in the network tests of both PS3 and 360(even though the PS3 obviously still says Type 2. It used to say Type 2, but it also used to have an error code at the bottom of the page). I've checked in games on each console, and they tell me I've got open NAT.
Now I still have one tiny problem. Red Dead Redemption. I play Red Dead Redemption online with two friends(who, incidentally, have the same router as me), and we haven't been able to communicate if we were using routers. We still can't, but I'm thinking that it's not my router anymore. I'm thinking his router has incorrect settings. Am I correct?
So here is the issue:
When I connect my modem directly to my computer (modem > computer) it works just fine, internet connects and everything through the direct ethernet connection.But when I connect the modem to the router and then try to connect wireless with any other computer (modem > router > wireless) nothing works. Not even when I have it connected directly from the router to the ethernet on the main computer. (Which has ALWAYS worked until now.
my brand new Linksys E1000 wireless router. I am really struggling and cannot figure out what I am doing wrong.
I live in The Netherlands, have a modem (DSL I think...) and can connect wired through the modem with no problems.
I installed the E1000 with the CD, followed all the steps and my laptop is finding the network. However, it's only local, no internet and I don't understand why. Have tried to connect (wired) my computer to the E1000 and the E1000 to the modem but that doesn't work either.
However, my 13" Macbook (running Lion) sometimes finds if hard to connect after I turn it on. I will have to continously turn off and on the wifi of the macbook to have it force to look at wifi networks. It will not be able to see also other wifi networks which are present in my neighbors which my windows 7 and other machines can see. After playing around with it I found that the macbook will connect to wifi only after I connect it momentarily via cable. I do this everytime I turn on my macbook.I just upgraded to a Macbook Pro running on Lion and the same thing happened. I tried the same solution of connecting first via cable but to my disappointment, would not see any wifi network including my neighbor's which again the other machines can see. So I am stuck with using cable for now.
View 5 Replies View Relatedis there a way i can block a website from being viewed.i would like to do this from the setup page of my e1000 under website restrictions.
View 1 Replies View RelatedLost password for router- how do I retrieve password.
View 2 Replies View Relatedwhere to find my guest user password
View 1 Replies View RelatedMy e1000 was working fine until it was accidentally unplugged. Now it doesn't work. I downloaded the set up program from the site and tried to run it, but it does not recognize an internet connection when I have the modem connected to the router and the router connected to the PC. The internet works when I connect the modem directly to the PC. I have unplugged everything and restarted the PC several times and tried running the software again, but no dice.
View 4 Replies View RelatedI have a linksys E1000 and i'm trying to open my NAT for xbox live. I mostly need it for call of duty: black ops because i cant connect to friends and i lag out of lobbies with friends. I've been trying to open my NAT for hours and nothing will work. ive tried forwarding ports, DMZ, UPnP, MTU sizes, and security things.
View 9 Replies View Relatedmy E1000 router locks up and I lose Internet connectivity until I unplug the router's power cord, wait for 10 seconds or so, then plug it back in and let it restart. This seems to be triggered (a.) when I land on a web page with intensive graphics, etc., that takes a while to load, or (b.) if I launch a web page really quickly while another one already is up. it doesn't just happen spontaneously when I'm working on the computer. This computer I'm working on is old and slow, which is why as per my earlier inquiry about having to reconfigure the router and network , I'm looking at changing to an up to date and faster model. I just updated to the latest firmware, probably a week or so ago, but the router was doing this before then and still is doing it now.
View 1 Replies View RelatedI have my router set up and life was good. i now want to forward a port. i go into apllications/gaming put the application name, the port i want to forward and click enable. Save changes and i get a changes save message. When the browser goes back to the applications/gaming screen no port shows as being forwarded. If i go to canyouseemenow.org the port shows as being closed.
View 3 Replies View Related