Cisco Wireless :: WLC 2504 - Some Clients Gets IP As Zero
Aug 29, 2012
I've problem with a WLC 2504. Some Clients like phones and Thin Clients get an IP 0.0.0.0.Software Version is 7.0.235.0. Test with a Laptop seams to be OK. Some printers also got an 0.0.0.0.Around 30% are not OK. also had the log: Impersonation of AP with Base Radio MAC 00:yy:yy:yy:yy:yyusing source address of 00:xx:xx:xx:xx:xx has been detected by the AP with MAC Address: 00:yy:yy:yy:yy:yy on its 802.11b/g radio whose slot ID is 0 The problem is, I cannot go to 7.2 version because I have 2 x AP 1231 and 2 x 1242 AP's.1231 AP's are not anymore supported in 7.2 Version.
View 14 Replies
ADVERTISEMENT
Oct 1, 2012
Is there a way to generate historic reports on how many clients have been using a WLAN on Cisco 2504?
View 1 Replies
View Related
May 29, 2013
While trying to connect to WiFi at remote sites APs, the connection is getting time out.User are getting error as 'Unable to connect to <WiFi-SSID>' The APs at corporate office are functioning properly and user are able to connect to the APs.
Wifi Controller: 2504 Software ver: 7.3.101.0
Authentication 802.1x
View 7 Replies
View Related
May 28, 2013
I have a WLC 2504(code 7.0.235) installed and two AP 3502 (local mode). RADIUS Server is a IAS runnning on my AD server.
I had a domestic AP before Cisco solution, using the same RADIUS server and everything was ok. After migration Windows 7 domain clients and Apple devices connects without issue. However when I try to connect non-domain windows 7 clients into wireless network (802.1X) and got failure. Apple devices out of domain can connect, certificate pop-up appears and connection flows.
I check certificates and everything looks ok for me. I remove a windows 7 client from domain and test it too, an got the same error. Certificate are install on windows 7 clients.
Could Cisco controller interfering in this authentication process ?
View 1 Replies
View Related
Feb 1, 2011
I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies
View Related
Jun 18, 2012
I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
Result of the command: "show running-config"
: Saved
:
ASA Version 7.2(4)
!
hostname ASA
domain-name default.domain.invalid
[code].....
what I need to add to get the vpn client to be able to ping the router and clients?
View 3 Replies
View Related
Nov 5, 2012
We currently have an ASA 5520 communicating with 10 ASA 5510's, all on static outside addresses. I was asked to add 5 additional 5510's on dynamic address. All worked well in testing until it was decided that some of the dynamic clients needed to talk to each other.
My testing shows packets just dying in the 5520.
View 1 Replies
View Related
Jul 6, 2012
I have a Netgear WNDR4500 running the stock firmware, acting as a router for my home. I also have 2 routers that are flashed with DD-WRT (Linksys WRT54G and Asus WL-520GU) running as client bridges. The Netgear is 192.168.1.1 and the other 2 client bridges are 192.168.1.2 and 192.168.10.3. The Netgear router is performing DHCP giving addresses from 192.168.10.100 to 192.168.10.254. I have numerous machines connected to the Netgear, wirelessly and wired, and numerous machines wired to each client bridge. All machines have IP addresses that are 192.168.10.100, 192.168.10.101, 192.168.10.102, etc... Everything is working fine, but I have one question: When I access the Netgear router, it shows the client bridges as clients, machines that are wired and wireless to the Netgear router are listed as clients, but the client list does not show any clients that are connected to the client bridges. I assumed that since the router is performing DHCP that all clients would show up.
View 2 Replies
View Related
Mar 2, 2013
Why a 2504 Poe? If it can not be used for AP.
View 10 Replies
View Related
Jan 22, 2013
I'm planning to upgrade our WLC 2504 from 7.2.111.3 to 7.4.100.0 but the cisco site says "WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time" Is it something about NCS? we have only 1 cisco WLC 2504 and 6 1142APs.. Also let me know is it possible to go directly from 7.2 to 7.4 ?
View 8 Replies
View Related
Nov 28, 2012
what is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
View 8 Replies
View Related
Aug 15, 2012
I have two WLC 2504 controllers. These controllers are for two different buildings. But they share a VLAN, and network address range. How can I control the access points to the register selected only at a specific controller.
Example:
AP 1 -> WLC 1
AP 2 -> WLC 2
AP 3 -> WLC 1
Since the buildings also broadcast in different SSID. The two controllers are in a mobility group.
View 4 Replies
View Related
Jul 12, 2012
If we update our ios on WLC do we have to add the certificate for AP's again or we don't need to do that.
View 4 Replies
View Related
Mar 13, 2013
Some time ago I updated a WLC, model 2504, from version 7.3 to 7.4.100.0. I also update the FUS (Field Upgrade Software) to the latest release, 1.8.0.0. Now I need to downgrade the WLC back to 7.3 version.
My doubt is: Can I just take the normal processes and downgrade the WLC back to 7.3, even with the FUS in version 1.8.0.0?
View 5 Replies
View Related
Jun 10, 2013
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
View 15 Replies
View Related
Aug 2, 2012
I currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies
View Related
Mar 12, 2013
I have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch 2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?
View 4 Replies
View Related
Jul 3, 2012
I've got a 1524 ap and it wont join my 2540 WLC. The messages I see in the WLC is RADIUS authorization is pending for the AP. I've added the MAC address of the ap under AP Policies using MIC. I dont have a radius server either so not sure how to tackle this one.When I run debug capwap events enale under the wlc I see the following messages:Discarding discovery request in LWAPP from AP supporting CAPWAP.
View 35 Replies
View Related
May 20, 2012
We have a 2504 on version 7.2.103.0 and 15 of the 1131 AG's.In short we cannot get the access points to register against the WLC, they seem to be caught up in a boot loop. They are seen on the WLC with a status of downloading, then once they have downloaded (Seen via CLI) I get an error message things I can confirm are The Country code is set to GB All ports are in Native VLAN Access points are ETSI type. It stops and restarts at syslog output DTLS-3-BAD-RECORD: Erroneous record recieved from x.x.x.x: Duplicate (replayed) record.
View 26 Replies
View Related
Oct 14, 2012
Can a 2504 WLC on a remote site provide guest access on one SSID, drop taht out locally on that site and provide corporate access on a second WLC that it then tunnls to a 5508 at the main corporate site ?
View 4 Replies
View Related
Jun 16, 2013
upgrade on the wireless controller 2504 from 7.0 to 7.4 is direct upgrade.My customer faced problem by upgrading the software 7.0 to 7.4 directly and the image hang.how should proceed recover the image 7.4/
View 7 Replies
View Related
Aug 28, 2012
I would like to get it clarified, that Cisco WLC 2504 running the code ( 7.2.110.0 ) does support IPv6 or not ?
From Cisco Documents they are asking to enable IPv6 support under WLAN > Edit Page, and Enabling mulicast on Ethernet Multicast Mode under Controller > General.
But from the GUI am not able to find the above two field, Even in Interface i created under Controller > interface is not accepting IPv6 address. I am able to configure IPv6 ACL .
Is any deployment document is available to show different scenarios with configuration.
Note - Am using Access point AIR-LAP1262N-N-k9
View 1 Replies
View Related
May 21, 2013
Currently I am using WLC 2504 with Software version 7.0.220.0. I am having some issues with Windows 8 clients they can't connect and I read on couple of review that wlc needs upgrade software.
I checked and latest versin is 7.4. Can I go to this version directly or I have to jump step by step.
View 3 Replies
View Related
Nov 29, 2012
I am trying to TFTP an image to a Cisco 2504 WLC. The management interface is 10.1.1.1 /24 and I have my PC connected to a port on the WLC with the IP address 10.1.1.10. However, I still do not have connectivity between the PC and WLC.
View 3 Replies
View Related
Mar 31, 2013
I am about to deploy a load of Aironet LWAPs into my organization. I've configured the WLC 2504 and have a couple of the APs working at our main site. I just needed to plug them in, and they worked perfectly, straight out the box. But I just want to know the following:
1 - will the same apply if I connect an AP at a remote site? Remote sites are on different subnets and connected via IPSEC. Will the remote APs just find the WLC?
2 - is there anything I need to set up especially on the WLC in order to make this work?
3 - what happens if the IPSEC connection drops?
View 4 Replies
View Related
May 26, 2013
My customer is seeing these Errors coming up on one of his 2504 WLC's (ver7.3) The MAC's and IP addresses Mentioned seem to be completely fictitious as the customers IP plan is way off these subnets and the vendor lookup tool cant resolve the MAC addresses.I can confirm that there is no conflict.I've seen them appear on other 2504's across his network on seperate occasions.
View 4 Replies
View Related
May 21, 2013
I have a 2504 WLC and 1042 ap's. Everything worked great in my test enviroment (of course). Now when I want to deploy the wireless, the ap's are not getting and ip for the windows dhcp server.
I have option 43 configured in dhcp, sub option 241>ip address of the controller
I have my A record in dns, cisco-capwap-controller.
*Mar 1 00:03:17.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
*Mar 1 00:03:27.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:27.054: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:37.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:47.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:57.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:04:07.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
View 3 Replies
View Related
Apr 4, 2013
We have a WLC 2504, since a few months, it was working fine, we have a guest Wlan configure with web authentication and the DHCP scope for this in the WLC. The problem today is that its no redirecting the web browser to 1.1.1.1, we try it with 3 laptops and they recieve a correct IP from the DHCP but still can not get redirect to the web authentication portal. Have the default configuration Internal (Default).
In laptops we check the firewall, dont have a proxy activate and have google DNS.. 4.2.2.2 8.8.8.8. In fact this laptops connected to this ssid before.
View 1 Replies
View Related
Nov 28, 2012
Can I set up a guest wifi connection on my Cisco WLC 2504 if I already have WLANs set up inside my corporate network? I want to use port 4 and connect it directly to my ISP so that it is outside of the corporate network. I set up an interface with a valid IP from the ISP and created a "Contractor" WLAN to use that interface.
View 6 Replies
View Related
Jul 16, 2012
I am trying to configure WLC 2504 with the following setup:
- three WLAN SSIDs
- management/ap-manager interface on VLAN 10
- guest WLAN on dynamic interface VLAN 20
- main WLAN on dynamic interface VLAN 30
- WLAN for tablet and smartphone devices VLAN 40
At this point switch trunking is configured and three WLANs are mapped to three dynamic different interfaces. I can see all associated APs (which are on the same subnet as management interface on VLAN 10), and can ping each of the APs as well as gateways on L3 switch Catalyst 3750-x. Also, on the WLC interface I see that all WLANs are enabled and SSIDs are set to broadcast, all AP radio is in 'up' mode. DHCPs are configured on management interface and on all dynamic interfaces. L3 switch gateways all have ip helper-address pointing to main DHCP. 'sh vlan' and 'sh int trunk' commands on the connected switches show correct settings.
However, I see absolutely no any SSIDs to connect to on any PC or Mac computer I tested.
View 2 Replies
View Related
Jan 16, 2012
I was wondering if the 2504 has the lobby ambassador feature available. Customer requires temp username/passwords for guests managed through web gui. I couldn't find conclusive documentation it was included so I figured I'd check here before calling Cisco.
View 2 Replies
View Related
May 10, 2012
We are installing a 2504 with management on VLAN2. The management port is on interface 1 which is attached to a layer 3 3750. From other VLANs in the network we cannot manage the 2504 controller with the web manager. We are running the latest code, 7.2.103.0, since we are using 3600 APs. We have a TAC case open, but spent 3 hrs with them and they can't figure out the problem. TAC did some debugging and saw that the 2504 is ARPing for the address of the PC on the other VLAN instead of sending the packet to its default gateway. How to get success with the management interface on a VLAN and managing the controller from another VLAN?
View 2 Replies
View Related
Aug 21, 2012
Is there way to group APs to get different profiles. I need to have some that have the 2.4GHz turned down and some wiht the 2.4 and 5.0 GHz on.
View 7 Replies
View Related
