Cisco Wireless :: WLC 2504 - No SSIDs Available To Connect
Jul 16, 2012
I am trying to configure WLC 2504 with the following setup:
- three WLAN SSIDs
- management/ap-manager interface on VLAN 10
- guest WLAN on dynamic interface VLAN 20
- main WLAN on dynamic interface VLAN 30
- WLAN for tablet and smartphone devices VLAN 40
At this point switch trunking is configured and three WLANs are mapped to three dynamic different interfaces. I can see all associated APs (which are on the same subnet as management interface on VLAN 10), and can ping each of the APs as well as gateways on L3 switch Catalyst 3750-x. Also, on the WLC interface I see that all WLANs are enabled and SSIDs are set to broadcast, all AP radio is in 'up' mode. DHCPs are configured on management interface and on all dynamic interfaces. L3 switch gateways all have ip helper-address pointing to main DHCP. 'sh vlan' and 'sh int trunk' commands on the connected switches show correct settings.
However, I see absolutely no any SSIDs to connect to on any PC or Mac computer I tested.
View 2 Replies
ADVERTISEMENT
Jan 31, 2013
I seem to only able to create a maximum of 16 WLAN SSIDs on WLC 2504.Can this be added through licensing or a software upgrade.
View 1 Replies
View Related
Feb 15, 2013
We are planning to implement Cisco wireless in our central office and branch office using Cisco 2504 WLC and Cisco 1602i Ap. Our branch office is connected via ip vpn and a separate broadband connection for urgent requirements. Usually all users are allowed to browse through central proxy server.I have been trying to find any possibility of giving guest access (web authentication) for branch office guests utilizing only the broadband connection which is connected to the branch office. Is there a possibility that Central WLC is reached using NAT from the BranchOffice AP and allowing guests to authenticate and surf the web at times IP VPN is unreachable.
View 4 Replies
View Related
May 29, 2013
While trying to connect to WiFi at remote sites APs, the connection is getting time out.User are getting error as 'Unable to connect to <WiFi-SSID>' The APs at corporate office are functioning properly and user are able to connect to the APs.
Wifi Controller: 2504 Software ver: 7.3.101.0
Authentication 802.1x
View 7 Replies
View Related
Feb 28, 2012
I just installed a brand new AP541N-A-K9 (running AP541N-K9-2.0(1) software) and cannot seem to add a SSID. I've tried both from CCA and directly from the Web interface (Wireless:Wireless Network Setup menu). The Add Another button doesn't seem to do anything. I've even tried multiple browser versions.
View 1 Replies
View Related
Mar 22, 2009
I have a 4404 with 3 SSID's configured on it. I only want all SSID's to be available on one floor in one building and not on any other AP's in any other building or floor.I thought the way to do it was via AP group but have not had any luck getting that to work. I setup a group for the AP's that I do not want all SSID's and then assigned those AP's to that group. However, I can still see all three SSID's where I only want to see 2 SSID's.
View 4 Replies
View Related
Mar 29, 2012
I want to split the usage of the AP so that visitors are on their own wireless connnection and VLAN.We have 2 WAP4410N APs. One AP acts as a repeater for the another AP.They are both in 4.0.4.2 firmware.We are using WPA2 RADIUS authentication, and would like for visitors to use WPA2 PSK. Under Wireless tab, I have 1 SSID, but the other 3 available boxes for SSIDs are greyed out.When I click in them, they will not allow me to type an ID.I watched a video of how to add SSIDs and VLANs, and it looked simple enough.He just clicked in the box and was able to add more IDs.Could my current config be preventing me from adding additional SSIDs?
View 6 Replies
View Related
Jun 15, 2012
I have here a couple of APs with c1130-k9w7-mx.124-25d.JA1 loaded as firmware.
I want to configure them with 2 SSID: 1 encrypted, 1 public. Each should go to its own vlan, and thus should have a trunk towards the switch.
My wireless experience approaches zero however, and I cannot get the APs to even send out an unencrypted public SSID.
The config that is currently on the AP, after trying a lot of things is:
gibbs#show run
Building configuration...
Current configuration : 3272 bytes
!
version 12.4
[Code].....
View 4 Replies
View Related
Jan 18, 2012
We recently received our WLC 5508, AP and switches to setup our WLAN but I'm having trouble getting it all to work. It's been months since the course and I'm having trouble troubleshooting the problem.I've setup the WLC, AP and switches and I have network connectivity to all. The WLC see's my AP and I have all my WLAN and interfaces configured (SSID broadcast is enabled) but I still don't see any SSID coming from the AP.
View 23 Replies
View Related
Mar 18, 2013
Is it possible to configure two SSIDs with same valn (default VLAN) with same IP addressing subnet on an autonomous 1240AG access point ios ver is 12.4 21a ja1.
View 3 Replies
View Related
Jan 10, 2012
I need to configure a WAP4410N for use on a small, very simple business network. There should be a corporate WLAN and a guest WLAN. The corporate WLAN should allow anyone connectd to it to access resources on the domain.
In front of the WAP is a cable modem/router and a basic Level 2 (web managed) switch. What do i have to do to segregate the corporate and guest networks.
I thought I would add the corporate WLAN to VLAN1 (assuming the default VLAN in the switch is VLAN1). Then I figured I could create the guest WLAN and assign it to VLAN2 which which will be controlled entirely by the 4410N (DHCP, DNS, etc.) Does this sound like the right way of going about things?
View 1 Replies
View Related
Apr 22, 2012
I have several Aironet 1231 APs most running 12.3(8)JEA software. There are 4 SSIDs on (each in separate VLAN), with only one broadcasting (called pubwifi). The broadcasting one is an open, unencrypted network: [code] After adding another braodcasting SSID (encrypted, separate VLAN), I encountered weird situation: my WiFi clients are unable to connect to pubwifi. It is not showing in the available networks or is showing as an "unknow" network. New encrypted/bradcasting ssid is advertaising just fine.
View 6 Replies
View Related
Sep 10, 2012
Currently my company has 1 primary SSID that is used throughout both floors of the building. We have 1252 LAPs which have 2.4 and 5Ghz antennas. I'm not sure if this issue is only with XP or perhaps it's the computer's drivers but we run into problems with end users going to a different location and having a very weak signal or nothing at all, yet coverage is fine. I believe the problem is the end user's machine selecting the strongest signal and it I have the feeling that switching bands isn't being done as it should when it's in range. So my question,
Should I split up our 1 SSID and created multiple SSIDs according to the location and include 5Ghz or 2.4Ghz in the SSID name so it's easier to ensure that users are connected to the proper signal? I want to ask if multiple SSIDs would still enable users to freely roam (as long as the ssids are configured) throughout the building without noticing a loss of signal but currently just having 1 SSID isn't really enabling people to freely roam around without connection issues.I don't believe having multiple SSIDs will be useful for the computer's choose their connection any more efficiently but allowing the user to manually see what they're connected to and pick something better according to their location.
View 3 Replies
View Related
May 22, 2012
I am running a WiFi network built on Cisco 1262 APs and Cisco WLC 5508. My APs broadcast two SSIDs, let call them "WiFi_Pay" and "WiFi_Free". I have a problem: when users migrate from "WiFi_Pay" to "WiFi_Free" (not moving, connecting to the same AP), the connection fails. If they try for second time, it is always successful. My task is to ensure that such migrations run smoothly and be successful from the first attempt.
View 2 Replies
View Related
Sep 9, 2012
I found a few older forum posts and documents online discussing how to create multiple SSIDs on 1 1252 AP using the WLC and they state that VLANs are needed for the interface and then I've read that multiple SSIDs on 1 interface are also possible. I'm not sure on how to actually configure this. I would like my 2.4Ghz radio on the 1252 to be associated with the current SSID in production and the 5Ghz band associated with another SSID that's in production. I couldn't find an option in the WLC or anything stated in the documents I've read about how to associate the radio band with the SSID.
View 5 Replies
View Related
Dec 26, 2012
Doing segregation of SSIDs Base on AP , I have the following scenario:
Head Office :
2 SSIDs (HO_WiFi , Guest) , Access Points which are working in connected mode and grouped on the default ap group .
Remote site:
2 SSIDs (Branch_Wifi , Guest) , Access Points working in flex connected mode and locally switching the traffic .
As shown above , I will be having Head Office , and other 20 Remote Sites with Access Points working in Flex connected mode. What is the best way to group AP and segregate SSID base on location. Above Scenario are build base on WLC 5508 and AP 1142.
View 9 Replies
View Related
Mar 19, 2013
I am trying to setup a RV180 and 3 wireless access points. I want the AP's to have 2 ssids that are isolated from each other. IE guest network and main network. I have setup VLAN's and my AP's support 802.1q and have ssid's with matching VID's. I was able to get this to work basically, but things seem to have gotten confusing when I plug the AP's into a POE switch instead of directly into the rv180. At this point I'm not sure exactly waht to ask. Maybe start by providing basic info on how I'm supposed to do this. I was under the impression that since both devices support 802.1q I could configure the VLANs on the router, and tell the AP's to apply a VID to the SSID and thing would work. This isn't the case unfortunately.
View 5 Replies
View Related
Mar 26, 2012
I am trying to provision three 1142 AP's so they broadcast multiple SSIDs. I have set the following commands, but I am not able to get more than one SSID to broadcast. As you can see I added the "guest-mode" command to one of the SSIDs which took it without problems. That other SSID does not accept the command.
dot11 ssid Test
vlan 2
authentication open
[Code].....
View 4 Replies
View Related
Dec 11, 2011
We have a Cisco 2505 WLC which can support 5 Ap's based on license. Is there any limitation on the no. of ssid's that can be configured on a wlc, how to determine that detail.
View 5 Replies
View Related
Dec 2, 2012
I have the need to run a few autonomous APs (1262) for some sites on satellite links. At a bare minimum I need to run two WLANs. One is wide open, and the other with an ACL that heavily restricts access. Is there any way to tie two WLANs to a single VLAN, while applying an ACL to just one WLAN?
View 4 Replies
View Related
Oct 22, 2012
I have two buildings that I'm trying to configure a bridge in between them using 2 1242AG APs.
Building A
PCOFFICE SSID on VLAN 200 Radio G
ROOT_1 SSID on Native VLAN 1 Radio A
Root Bridge
Building B
FDAPC SSID on Native VLAN 1 Radio G
ROOT_1 SSID on Native VLAN 1 Radio A
We are using directional antenna. I know they are lined up properly because I have them both down and in front of me. I'm getting an error on the Building B AP that says " No SSID with VLAN configured. Dot11Radio1 not started." and I'm unable to get this to work. The bridge was working before I added the VLAN and encryption/WPA information for the PCOFFICE and FDAPC SSIDs
View 15 Replies
View Related
May 13, 2013
I have 2 cisco 1242Ag APs in one building and 7 in other building installed in my infrastructure. All these 9 APs are connected to WLC and all of them are added to default ap group to broadcast all the ssid... But 7 in the second bulding are working properly, but the 2 in the other building are not broadcasting the ssids. I checked the configuration in both APs and WLC as well... All the 9 APs are having the same configuration.
View 12 Replies
View Related
Aug 26, 2012
We have a 5508 controller with about 40 LAPs, running AIR-CT5500-K9-7-2-103-0-FUS software.The need has arose to have LAPs in various locations that only broadcast specific SSIDs.
I've got seperate dyanmic interfaces already created.We have 3 "Normal" SSIDs that we broadcast to the LAPs already associated with the 5508.2 more SSIDs were created (2 different purposes).
I just can't figure out how to get it to certain LAPs to only broadcast the specific SSIDs, while the rest broadcast the normal 3, but not those 2 new ones.
View 13 Replies
View Related
Jun 20, 2012
Although it does accept it in the setup wizard, you cannot change it in the vap list later on, it will throw a popup telling you there's an invalid character.
I'm running firmwarte 1.0.0.3
View 11 Replies
View Related
Jan 10, 2012
I am in the process of installing an Aironet 1140 standalone AP. I have not worked with these AP's before. I will be connecting it to one of the PoE ports on the existing ASA 5505. My goal is to have 2 SSID's, one for internal network and one for guest internet only, no access to internal LAN. I want to have the internal wifi clients and the guest clients on seperate IP networks. The internal clients obtain DHCP from the existing server and use the ASA DHCP server for the guest clients. And of course, I would like the ability to manage the AP from the internal network. I am providing copies of my current configs for both the ASA and Aironet.
View 4 Replies
View Related
May 20, 2012
I have a question regarding to the maximmum number of active SSID's on a WLC 5500 with 3500i, it's my understanding that the 3500i can support 16 active SSID's is it the same when connected to the WLC? Also, if possible would the WLC shutdown un-used Radios or maybe after hours?
View 1 Replies
View Related
Sep 7, 2011
What is the maximum number of WLANs/SSIDs that can be configured on a H-REAP access point? I have a network with 3502i AP's, centralised WLC's in the data centre running 7.0.116.0, and WCS version 7.0.172.0.
I was successfully running 2 SSID's at a remote site, one SSID was configured for H-REAP local switching, dropping out to the local site VLAN X, and the other SSID was a central switching guest WLAN anchored to a WLC in a DMZ.I configured a third SSID at the local site running H-REAP local switching, and now I cannot see the guest SSID anymore, it does not appear to be broadcasting.Is there a maximum of 2 WLANs/SSIDs when operating in H-REAP mode?
View 5 Replies
View Related
Nov 28, 2011
I just got the E3200 and it's a pretty good router. Configured it to have 1 SSID as the 5Ghz SSID and the other as the 2.4 Ghz SSID. Since there are 2 SSIDs broadcasted, I was expecting machines connected to each distinct SSID to not be able to see each other, ie expecting the 5Ghz SSID to be a private LAN1 and the 2.4 Ghz SSID to be LAN2? It turns out machines on either SSID can see each other, so it looks like it on 1 big LAN even though there are 2 SSIDs.Doesn't a SSID map to a unique LAN even though they are in the same router?
View 2 Replies
View Related
Jan 17, 2013
I have recently purchase Aironet Access Point. I'm pretty new to Cisco systems and what i'm try to do is have the access point broadcast multiple SSIDs lets call them Guest and Admin. My problems is when i config router to have a DHCP address it works perfectly fine but when i assign a static IP it shows all the any connected device as unkown with IP 0.0.0.0. So i'm guessing i will need to setup a dhcp server. Is there a way access point can have its own DHCP server and IP address ( i don't want to use any from my STATIC ip subnet as i dont know alot of empty ones left) like home wifi router where they assign each device an IP like 192.168.0.1. Is this possible?
View 1 Replies
View Related
Apr 11, 2012
I set up my new EA4500 last night, and configured the 5Ghz and 2.4Ghz bands with separate SSIDs (as recommended). While I can see the 2.4Ghz band with all of my devices, I cannot see the 5Ghz band with any of them.I followed the advice given (including the settings shown) on the EA4500 FAQ.Title: Personalizing and connecting to the 5 GHz wireless band on a Linksys Wireless-N routerArticle ID: 21466.Did that *multiple* times, and still nothing. I do have a dual-band capable adapter (Netgear RangeMax WNDA3100 Dual Band Wireless-N Adapter) that I know works on 5Ghz (because I had it working on my old dual-band WDNR3700v1). Similarly, I have PCs sitting less than 20 feet away that were previously able to see the 5Ghz band on my old router, but are now unable to see it on the EA4500.
View 9 Replies
View Related
May 13, 2013
I am trying to build a new network from scratch, I have the WLC 5508 w/ Aironet 3600e APs connected to my Netgear Smart Switches and a Linksys RV082 router that I'm using as my DHCP server with several VLANs for several stuff on my Switches.
I have 2 questions:
1. Can I have 5 Interfaces configured on 5 different VLANs, each SSID on each a different Port:
Port 1: Controller management only=> 192.168.x.x /24
Port 2: SSID 1: WiFi Internal=> 172.16.x.x/12 (Radius Auth with no sharing)
Port 3: SSID 2: WiFi Internal w/ sharing=> 192.168.x.x/24 (Radius Auth with sharing)
Port 4 :SSID 3: WiFi Guest=> 10.0.x.x/8 (Web Auth)
Port 5: SSID 4: WiFi IT=> 192.168.x.x/24 ( Radius or certificate Auth with access to the controller management interface)
2. How can I use the Controller as the DHCP server for all the WiFi traffic, and how should that be configured to work with my other DHCP server?
View 3 Replies
View Related
Jun 21, 2011
I am trying to use two different SSID's on my 1131AG each with different security, is this possbile?
View 1 Replies
View Related
Nov 13, 2011
I have a DIR-615 Wireless N D-Link router. Simple setup, comcast cable modem ---> router ---> wireless signal to house. For some reason, kinda out of nowhere (can't recall precisely when it began doing this) the router is broadcasting 2 SSID's, one is my configured network, and another network named: D-Link_Wireless. Whats strange thou, is that some devices detect the D-Link_Wireless SSID and others do not. When I go into the router config, all I see is the one configured network, PanzerNet. I wouldn't care so much but I think it's causing some conflictions with my DNS address, making me have to constantly reset my router..
View 14 Replies
View Related
