Cisco Wireless :: Create A Maximum Of 16 WLAN SSIDs On WLC 2504
Jan 31, 2013I seem to only able to create a maximum of 16 WLAN SSIDs on WLC 2504.Can this be added through licensing or a software upgrade.
View 1 Replies
ADVERTISEMENT
Cisco Wireless :: WLC 2504 - No SSIDs Available To Connect
Jul 16, 2012I am trying to configure WLC 2504 with the following setup:
- three WLAN SSIDs
- management/ap-manager interface on VLAN 10
- guest WLAN on dynamic interface VLAN 20
- main WLAN on dynamic interface VLAN 30
- WLAN for tablet and smartphone devices VLAN 40
At this point switch trunking is configured and three WLANs are mapped to three dynamic different interfaces. I can see all associated APs (which are on the same subnet as management interface on VLAN 10), and can ping each of the APs as well as gateways on L3 switch Catalyst 3750-x. Also, on the WLC interface I see that all WLANs are enabled and SSIDs are set to broadcast, all AP radio is in 'up' mode. DHCPs are configured on management interface and on all dynamic interfaces. L3 switch gateways all have ip helper-address pointing to main DHCP. 'sh vlan' and 'sh int trunk' commands on the connected switches show correct settings.
However, I see absolutely no any SSIDs to connect to on any PC or Mac computer I tested.
Cisco Wireless :: Maximum Number Of Active SSIDs On WLC5500 With 3500i
May 20, 2012I have a question regarding to the maximmum number of active SSID's on a WLC 5500 with 3500i, it's my understanding that the 3500i can support 16 active SSID's is it the same when connected to the WLC? Also, if possible would the WLC shutdown un-used Radios or maybe after hours?
View 1 Replies View RelatedCisco Wireless :: Setup A 2504 To Have One Guest WLAN And One Staff WLAN?
Jun 10, 2013I would like to setup a 2504 to have one Guest WLAN and one Staff WLAN with a controller port for each WLAN connected to different devices.
I would prefer to connect the WLC Guest port to an ASA 5510 and the WLC Staff port to an internal 2960S switch. Will this work? I haven't setup a 2500 series controller previously.
Cisco Wireless :: 1252 - Create Multiple SSIDs?
Sep 10, 2012Currently my company has 1 primary SSID that is used throughout both floors of the building. We have 1252 LAPs which have 2.4 and 5Ghz antennas. I'm not sure if this issue is only with XP or perhaps it's the computer's drivers but we run into problems with end users going to a different location and having a very weak signal or nothing at all, yet coverage is fine. I believe the problem is the end user's machine selecting the strongest signal and it I have the feeling that switching bands isn't being done as it should when it's in range. So my question,
Should I split up our 1 SSID and created multiple SSIDs according to the location and include 5Ghz or 2.4Ghz in the SSID name so it's easier to ensure that users are connected to the proper signal? I want to ask if multiple SSIDs would still enable users to freely roam (as long as the ssids are configured) throughout the building without noticing a loss of signal but currently just having 1 SSID isn't really enabling people to freely roam around without connection issues.I don't believe having multiple SSIDs will be useful for the computer's choose their connection any more efficiently but allowing the user to manually see what they're connected to and pick something better according to their location.
Cisco Wireless :: Not Able To Get DHCP IP Via 2504 WLAN Controller
Jan 7, 2013I have a Cisco Wlan Controller 2504 with 1042N AP (3-nos) every thing was working fine from past 2 months. Now i am getting a issue with clients which are connected to the wireless AP, they are not able to get an dhcp IP address from the 2960 Switch (DHCP Server). The clients are getting IP address as 0.0.0.0. [code]
View 36 Replies View RelatedCisco Wireless :: 2504 - Reports On How Many Clients Using WLAN
Oct 1, 2012Is there a way to generate historic reports on how many clients have been using a WLAN on Cisco 2504?
View 1 Replies View RelatedCisco Wireless :: Migrating WLAN Controller 2125 To 2504
May 29, 2012I will migrate a Cisco WLAN Controller 2125 to 2504,So I have one question?I need to make all configuration into the new Wlan Controller or I can migrate with one tool or something else?
View 15 Replies View RelatedCisco Wireless :: HTTP Redirect - 2504 WLAN Controller
Apr 23, 2012I have a 2504 and my goal is to automatically redirect a users home page when they connect to a certain internal website. Authentication isn't a real concern just now.
Is it possible to simply have a users home page redirected when they open their browser upon connecting to the SSID? All of the documents available have stated to use 802.1x / RADIUS or other fancy tools.
Cisco Wireless :: 2504 Client Unable To Get IP Address On Guest Wlan
Feb 23, 2013I recently setup a 2504 WLC that has two primary WLANs (internal and guest) which get their IP addresses from a central DHCP server using the local router's broadcast forwarding. Things seem to be working well for the internal wlan, but clients on the guest wlan don't seem to be getting IP addresses. If I give the client a static IP they are able to communicate across the wlan okay.
It is worth noting that I am using LAG between the controller and router and this guest wlan is really just a regular wlan (with PSK) that has an access-list applied to force it to the internet only. The access-list should be allowing dhcp requests through, but in any case, I removed the access-list and it made no difference.
Here is a debug client for a machine connected to the guest vlan (vlan 33). The internal wlan is on the 10.10.10.0/24 network (same as wired and same that the AP's are connected to) and the guest wlan is 10.33.0.0/16. I don't understand why I am seeing the dhcp request come from the internal vlan/ wlan first and it gets an IP address on this network. I then see a request on the guest wlan/vlan at which point it appears to get a valid IP address on the guest network (10.33.0.0), but the client never sees this. [code]
Cisco Wireless :: 2504 Printing Solution For Guest WLAN Users?
Sep 19, 2012My customer has multiple sites, each with a 2504 WLC.A data center with a 5508 in the DMZ acting as Anchor for the remote sites.ACS 5.x and NCS Prime.All guest users will egress to the internet via a Vlan in the DMZ.Authentication is currently web-auth on the Anchor, but will move to NCS once that is fully deployed.
Is it possible to put a printer in each site for Guest WLAN users to use?
Cisco Wireless :: 2504 And 1142N AP To Create Individual User Accounts Who Are Connected
Apr 20, 2011We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point.Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?
View 11 Replies View RelatedCisco Wireless :: Setup 2504 WLAN Controller And 1142N Access Point?
Jun 13, 2013We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?
View 1 Replies View RelatedCisco :: 2504 Configured One WLan With External Web-authentication
Jul 4, 2012I have Cisco WLC 2504.I was configured one wlan with external web-authentication.External web server is apache on freebsd.When user connect to wlan and open web browser, wlc redirects client to external web page, where client must input hist credentials.When client click "submit" button on external web auth page, wlc initiates RADIUS request to radius server.Radius server(freeradius) is on the same server, where apache running.
sometimes, when client enter credentials on external page and click "submit" button, wlc suddenly redirect client on internal default auth page.
Routers / Switches :: Modem And Router Won't Create Internet Using WLAN?
Nov 23, 2012Trouble connecting to the internet wireless with Motorola SB6120 and Linksys WRT120N. The modem works directly with LAN but as soon as I try to use the router, I can connect to the network but no internet is available.
View 4 Replies View RelatedCisco :: Set Maximum Bandwidth For Entire Wlan Or For Entire Vlan In WLC 5508?
Jul 31, 2011if its possible to set a maximum bandwidth for the entire wlan or for entire Vlan in the WLC 5508 ?
View 3 Replies View RelatedCisco Wireless :: New AP541n With No SSIDs?
Feb 28, 2012I just installed a brand new AP541N-A-K9 (running AP541N-K9-2.0(1) software) and cannot seem to add a SSID. I've tried both from CCA and directly from the Web interface (Wireless:Wireless Network Setup menu). The Add Another button doesn't seem to do anything. I've even tried multiple browser versions.
View 1 Replies View RelatedCisco Wireless :: 4404 How To Limit SSIDs Per AP
Mar 22, 2009I have a 4404 with 3 SSID's configured on it. I only want all SSID's to be available on one floor in one building and not on any other AP's in any other building or floor.I thought the way to do it was via AP group but have not had any luck getting that to work. I setup a group for the AP's that I do not want all SSID's and then assigned those AP's to that group. However, I can still see all three SSID's where I only want to see 2 SSID's.
View 4 Replies View RelatedCisco Wireless :: WAP4410N Cannot Add Additional SSIDs
Mar 29, 2012I want to split the usage of the AP so that visitors are on their own wireless connnection and VLAN.We have 2 WAP4410N APs. One AP acts as a repeater for the another AP.They are both in 4.0.4.2 firmware.We are using WPA2 RADIUS authentication, and would like for visitors to use WPA2 PSK. Under Wireless tab, I have 1 SSID, but the other 3 available boxes for SSIDs are greyed out.When I click in them, they will not allow me to type an ID.I watched a video of how to add SSIDs and VLANs, and it looked simple enough.He just clicked in the box and was able to add more IDs.Could my current config be preventing me from adding additional SSIDs?
View 6 Replies View RelatedCisco Wireless :: Configure 1131 AP With 2 Ssids
Jun 15, 2012I have here a couple of APs with c1130-k9w7-mx.124-25d.JA1 loaded as firmware.
I want to configure them with 2 SSID: 1 encrypted, 1 public. Each should go to its own vlan, and thus should have a trunk towards the switch.
My wireless experience approaches zero however, and I cannot get the APs to even send out an unencrypted public SSID.
The config that is currently on the AP, after trying a lot of things is:
gibbs#show run
Building configuration...
Current configuration : 3272 bytes
!
version 12.4
[Code].....
Cisco Wireless :: WLC 5508 / No SSIDs Are Broadcasting
Jan 18, 2012We recently received our WLC 5508, AP and switches to setup our WLAN but I'm having trouble getting it all to work. It's been months since the course and I'm having trouble troubleshooting the problem.I've setup the WLC, AP and switches and I have network connectivity to all. The WLC see's my AP and I have all my WLAN and interfaces configured (SSID broadcast is enabled) but I still don't see any SSID coming from the AP.
View 23 Replies View RelatedCisco Wireless :: 1240AG - Two SSIDs With Same Subnet
Mar 18, 2013Is it possible to configure two SSIDs with same valn (default VLAN) with same IP addressing subnet on an autonomous 1240AG access point ios ver is 12.4 21a ja1.
View 3 Replies View RelatedCisco Wireless :: Configure WAP4410N With Multiple SSIDS
Jan 10, 2012I need to configure a WAP4410N for use on a small, very simple business network. There should be a corporate WLAN and a guest WLAN. The corporate WLAN should allow anyone connectd to it to access resources on the domain.
In front of the WAP is a cable modem/router and a basic Level 2 (web managed) switch. What do i have to do to segregate the corporate and guest networks.
I thought I would add the corporate WLAN to VLAN1 (assuming the default VLAN in the switch is VLAN1). Then I figured I could create the guest WLAN and assign it to VLAN2 which which will be controlled entirely by the 4410N (DHCP, DNS, etc.) Does this sound like the right way of going about things?
Cisco Wireless :: Aironet 1231AP - Broadcasting 2 SSIDs
Apr 22, 2012I have several Aironet 1231 APs most running 12.3(8)JEA software. There are 4 SSIDs on (each in separate VLAN), with only one broadcasting (called pubwifi). The broadcasting one is an open, unencrypted network: [code] After adding another braodcasting SSID (encrypted, separate VLAN), I encountered weird situation: my WiFi clients are unable to connect to pubwifi. It is not showing in the available networks or is showing as an "unknow" network. New encrypted/bradcasting ssid is advertaising just fine.
View 6 Replies View RelatedCisco Wireless :: 5508 / 1262 - Roaming Between Two SSIDs On Same AP
May 22, 2012I am running a WiFi network built on Cisco 1262 APs and Cisco WLC 5508. My APs broadcast two SSIDs, let call them "WiFi_Pay" and "WiFi_Free". I have a problem: when users migrate from "WiFi_Pay" to "WiFi_Free" (not moving, connecting to the same AP), the connection fails. If they try for second time, it is always successful. My task is to ensure that such migrations run smoothly and be successful from the first attempt.
View 2 Replies View RelatedCisco Wireless :: Configure Different SSIDs For Both Bands On 1252 And WLC?
Sep 9, 2012I found a few older forum posts and documents online discussing how to create multiple SSIDs on 1 1252 AP using the WLC and they state that VLANs are needed for the interface and then I've read that multiple SSIDs on 1 interface are also possible. I'm not sure on how to actually configure this. I would like my 2.4Ghz radio on the 1252 to be associated with the current SSID in production and the 5Ghz band associated with another SSID that's in production. I couldn't find an option in the WLC or anything stated in the documents I've read about how to associate the radio band with the SSID.
View 5 Replies View RelatedCisco Wireless :: WLC 5508 AP 1142 - SSIDs Segregation
Dec 26, 2012Doing segregation of SSIDs Base on AP , I have the following scenario:
Head Office :
2 SSIDs (HO_WiFi , Guest) , Access Points which are working in connected mode and grouped on the default ap group .
Remote site:
2 SSIDs (Branch_Wifi , Guest) , Access Points working in flex connected mode and locally switching the traffic .
As shown above , I will be having Head Office , and other 20 Remote Sites with Access Points working in Flex connected mode. What is the best way to group AP and segregate SSID base on location. Above Scenario are build base on WLC 5508 and AP 1142.
Cisco Routers :: RV180 - Setting Up VLANs For Wireless APs With Two SSIDs
Mar 19, 2013I am trying to setup a RV180 and 3 wireless access points. I want the AP's to have 2 ssids that are isolated from each other. IE guest network and main network. I have setup VLAN's and my AP's support 802.1q and have ssid's with matching VID's. I was able to get this to work basically, but things seem to have gotten confusing when I plug the AP's into a POE switch instead of directly into the rv180. At this point I'm not sure exactly waht to ask. Maybe start by providing basic info on how I'm supposed to do this. I was under the impression that since both devices support 802.1q I could configure the VLANs on the router, and tell the AP's to apply a VID to the SSID and thing would work. This isn't the case unfortunately.
View 5 Replies View RelatedCisco Wireless :: 1142 IOS Autonomous Multiple SSIDs Broadcast
Mar 26, 2012I am trying to provision three 1142 AP's so they broadcast multiple SSIDs. I have set the following commands, but I am not able to get more than one SSID to broadcast. As you can see I added the "guest-mode" command to one of the SSIDs which took it without problems. That other SSID does not accept the command.
dot11 ssid Test
vlan 2
authentication open
[Code].....
Cisco Wireless :: 2505 Any Limitation On Number Of Ssids That Can Be Configured On Wlc
Dec 11, 2011We have a Cisco 2505 WLC which can support 5 Ap's based on license. Is there any limitation on the no. of ssid's that can be configured on a wlc, how to determine that detail.
View 5 Replies View RelatedCisco Wireless :: 1262 Multiple SSIDs And ACLs On Autonomous AP
Dec 2, 2012I have the need to run a few autonomous APs (1262) for some sites on satellite links. At a bare minimum I need to run two WLANs. One is wide open, and the other with an ACL that heavily restricts access. Is there any way to tie two WLANs to a single VLAN, while applying an ACL to just one WLAN?
View 4 Replies View RelatedCisco Wireless :: 1242AG Bridge / VLAN And Multiple SSIDs?
Oct 22, 2012I have two buildings that I'm trying to configure a bridge in between them using 2 1242AG APs.
Building A
PCOFFICE SSID on VLAN 200 Radio G
ROOT_1 SSID on Native VLAN 1 Radio A
Root Bridge
Building B
FDAPC SSID on Native VLAN 1 Radio G
ROOT_1 SSID on Native VLAN 1 Radio A
We are using directional antenna. I know they are lined up properly because I have them both down and in front of me. I'm getting an error on the Building B AP that says " No SSID with VLAN configured. Dot11Radio1 not started." and I'm unable to get this to work. The bridge was working before I added the VLAN and encryption/WPA information for the PCOFFICE and FDAPC SSIDs
Cisco Wireless :: 1242Ag / Access Point Does Not Broadcast The Ssids From WLC
May 13, 2013I have 2 cisco 1242Ag APs in one building and 7 in other building installed in my infrastructure. All these 9 APs are connected to WLC and all of them are added to default ap group to broadcast all the ssid... But 7 in the second bulding are working properly, but the 2 in the other building are not broadcasting the ssids. I checked the configuration in both APs and WLC as well... All the 9 APs are having the same configuration.
View 12 Replies View Related