I would like to setup a 2504 to have one Guest WLAN and one Staff WLAN with a controller port for each WLAN connected to different devices.
I would prefer to connect the WLC Guest port to an ASA 5510 and the WLC Staff port to an internal 2960S switch. Will this work? I haven't setup a 2500 series controller previously.
I recently setup a 2504 WLC that has two primary WLANs (internal and guest) which get their IP addresses from a central DHCP server using the local router's broadcast forwarding. Things seem to be working well for the internal wlan, but clients on the guest wlan don't seem to be getting IP addresses. If I give the client a static IP they are able to communicate across the wlan okay.
It is worth noting that I am using LAG between the controller and router and this guest wlan is really just a regular wlan (with PSK) that has an access-list applied to force it to the internet only. The access-list should be allowing dhcp requests through, but in any case, I removed the access-list and it made no difference.
Here is a debug client for a machine connected to the guest vlan (vlan 33). The internal wlan is on the 10.10.10.0/24 network (same as wired and same that the AP's are connected to) and the guest wlan is 10.33.0.0/16. I don't understand why I am seeing the dhcp request come from the internal vlan/ wlan first and it gets an IP address on this network. I then see a request on the guest wlan/vlan at which point it appears to get a valid IP address on the guest network (10.33.0.0), but the client never sees this. [code]
My customer has multiple sites, each with a 2504 WLC.A data center with a 5508 in the DMZ acting as Anchor for the remote sites.ACS 5.x and NCS Prime.All guest users will egress to the internet via a Vlan in the DMZ.Authentication is currently web-auth on the Anchor, but will move to NCS once that is fully deployed.
Is it possible to put a printer in each site for Guest WLAN users to use?
My customer need creates some separately web portal for some SSID (Guest and Staff), 01 web portal for Guest and 01 Web portal for Staff. Can WLC2504 can support this features ?
View 2 Replies View RelatedWe are deploying 3600 AP's with a 2504 and would like to create multiple SSID's that are mapped to unique VLANs so we can control the traffic at the Firewall. We have the 2504 up and running with AP's but there appears to be no where in the 2504 controller Web GUI to configure a VLAN mapping to an SSID. Any pointers to documentation on how to configure?
View 1 Replies View RelatedWe are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?
View 1 Replies View RelatedWe're looking at deploying both office extend and also a guest wlan. Both would require a WLC in the DMZ.My question is can one 5508 WLC be both a guest anchor and have office extend APs on it at the same time?
View 2 Replies View RelatedI have a Cisco Wlan Controller 2504 with 1042N AP (3-nos) every thing was working fine from past 2 months. Now i am getting a issue with clients which are connected to the wireless AP, they are not able to get an dhcp IP address from the 2960 Switch (DHCP Server). The clients are getting IP address as 0.0.0.0. [code]
View 36 Replies View RelatedIs there a way to generate historic reports on how many clients have been using a WLAN on Cisco 2504?
View 1 Replies View RelatedI will migrate a Cisco WLAN Controller 2125 to 2504,So I have one question?I need to make all configuration into the new Wlan Controller or I can migrate with one tool or something else?
View 15 Replies View RelatedI seem to only able to create a maximum of 16 WLAN SSIDs on WLC 2504.Can this be added through licensing or a software upgrade.
View 1 Replies View RelatedI have a 2504 and my goal is to automatically redirect a users home page when they connect to a certain internal website. Authentication isn't a real concern just now.
Is it possible to simply have a users home page redirected when they open their browser upon connecting to the SSID? All of the documents available have stated to use 802.1x / RADIUS or other fancy tools.
1 router 881w with a site-to-site VPN connected to a switch and a wireless which allows internal users to access the VPN via wireless (this is like a backup, if the switch fails, then they can use the wireless). Everything's working fine so far. Now I want to configure a second WLAN for guest but I'm not really sure if this configuration will work:
ROUTER:
ip dhcp excluded-address 192.168.100.1 192.168.100.200
!
ip dhcp pool GuestNetwork
network 192.168.100.0 255.255.255.0
default-router 192.168.100.1
dns-server 8.8.8.8
[code]....
If it's not clear I want that everyone that is connected to the guest WIFI receives an IP address from the range I wrote before and then goes directly to the internet.
Can I limit bandwith for guest in a wlan network with out Wlan controller? and of course, how can I do it?P.S.: I heard something about bronze profile in a wlan controller envoiroment, I need something like that but in an independent AP.
View 3 Replies View RelatedWe have a strange problem. We have a WCS v.7.0.172 that controls our two WLC v.7.0.116 and we have also two "Anchor Controller" WLC
v.7.0.116 for Guest Access.
We use the LAP1142N and every AP has two SSID's. One for internal data traffic and the other one for the guests.
Now the problem is, that even if we have internal and external user on the same AP, the guest users gets disconnected after a few time. Sometimes after 20 minutes, sometimes after 90 minutes...but the user is still working. It's really irregular.
I tried to extend the Range of the Guest WLAN of the E2000 with several different Access Points vom TP-Link. (Last try: TL-WA901D) The Access Point recognises the WLAN and sometimes it has a connection for a short time. But then the whole WLAN is breaking down, sometimes the Router E200 hangs up, also with the LAN connections. The E200 is connected to a sky-DSL Router and works fine when no additional access point is connected. In the web-Interface of the E2000 I cant setup any specific Guest-WLAN settings.
View 1 Replies View RelatedI've been asked to create 2 wireless networks for guest access. They are to be used by clients of 2 different companies and they have asked for the website of each company to automatically open as a landing page. e.g.
-WLAN1 - password is companyname1 - landing page = www.companyname1.com
-WLAN2 - password is companyname2 - landing page = www.companyname2.com
Is this possible with our 5508 WLC? I have googled it and can see that you can set a web auth page but I need different landing pages depending on which WLAN is connected to.
Looking to add time of day restrictions to our Guest WLAN that is currently in its pilot phase.
Is there a way to config time of day access to a WLAN ?
I have a strange situation on my guest wireless LAN.The guest WLAN is configured as an SSID "GUEST" on Cisco 1142 lightweight APs, with WiSM controller and WLC software version 7.0.230.0.
For simple Internet access using this SSID, we have a web policy, which causes a web page to be displayed when the user opens his/her browser, and on this web page, the user must click on an "Accept" button in order to accept the terms and conditions of use. Once the user accepts, the browser will then go to the web site which the user wishes to open. When using this mode of access, everything is fine.
However, there is also a pre-authentication ACL, which allows certain types of VPN traffic to reach the Internet without the user being required to accept terms and conditions. The ACL allows ESP, IKE (UDP/500), IKE over UDP (UDP/4500), DNS, HTTPS/SSL (TCP/443), DHCP client and server (UDP/67,68).The pre-auth ACL actually works as intended; and the ACL traffic is NOT allowed when the ACL is removed. This is exactly as it should be.
However, when using, for example, a VPN client such as the Cisco VPN client, or the Cisco AnyConnect client, via this guest SSID without user acceptance, the WLAN regularly and predictably stops passing traffic. This is 100% repeatable and predictable; it happens every 300 seconds, or possibly slightly longer. I have only used my PC clock to time it so the timing isn't all that accurate but I'm sure it's within a few seconds.
Given that the problem happens at the same time interval and is constant, I guessed there must be some configuration item which needs to be altered, but I've looked extensively at the controller GUI (we actually use WCS here) and I can't see anything that looks even remotely related to this.
We are planning a WLAN upgrade and the security policy is to forward wireless Guest user traffic to the DMZ controllers. We are now considering the Virtual WLAN Controller and all AP's will register with the virtual controllers and we will use Flexconnect for Staff and internal traffic that will switch their traffic onto the local switch.
We wish to forward the guest traffic to the DMZ Guest Anchor controller which will be a 5508 controller. This will also offer Office Extend AP service.I have looked at teh virtual controller docs and not very clear if this deployment model is supported. Below is a diagram of what we wish to deploy and is this a supported deployment model.
I want to setup a webpage for my guest network (no authentication) users. When the client connects to the open guest network and upon opening a browser they would be directed to a survey that I would like them to take, if they don't want to take it they can begin browsing to other sites without issue. How do I do this on a my 5508 WLC?
View 12 Replies View RelatedI have a wrt54g router and would like to separate the WLAN clients from accessing computers and servers on the LAN... in other words I would like to make it a "guest" network. I've put the router in "router" mode instead of "gateway". I just want to be sure if that is the best thing I can do in terms of turning the wireless network into an isolated one.
View 4 Replies View RelatedI have Cisco WLC 2504.I was configured one wlan with external web-authentication.External web server is apache on freebsd.When user connect to wlan and open web browser, wlc redirects client to external web page, where client must input hist credentials.When client click "submit" button on external web auth page, wlc initiates RADIUS request to radius server.Radius server(freeradius) is on the same server, where apache running.
sometimes, when client enter credentials on external page and click "submit" button, wlc suddenly redirect client on internal default auth page.
When a guest user first trys to access the "guest" WLAN, they are presented with a "certificate page" before the web athentication page / login is presented. The WLC forces an internal redirect to https://1.1.1.1 causing the certificate page to appear. Can this be bypassed? I am runiing 5508 with 7.0.220.0.
View 12 Replies View RelatedStrange issue that our support staff is seeing on our guest WLAN. I have 2 wlans, 1 is production and authenticates our Domain controllers, this is working fine. The other is a wlan that has restricted access internally, I allow http, https and VPN access out only.
It appears that on the guest wlan, after random amount of time an established VPN connection using Cisco VPN client disconnects. Wireless connectivity doesnt appear to go down, just the vpn connection.
On this guest wlan, I have configured QOS bronze and I read a link where this may be affecting the UDP conversation between VPN client and end point.
I have setup guest access on the controller and this is not working at the moment.
DHCP server setup on the controller for the Guest users.
You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
I have 2 5508s (foreign and anchor both running 7.2.110.0) with an open WLAN configured via mobility anchors. This configuration works and has no problems. My next task is to incorporate a webauth page (accept/reject) to present the clients with AUP information, etc. On the foreign controller I created a test WLAN (open) and setup webauth Passthrough using the Cisco webauthbundle (wap.html), this works as intended, no issues. However I am at a loss as to how to incorporate the webauth Passthrough functionality on the WLAN that is configured for the mobility anchor.
View 2 Replies View RelatedI have my wlc 4400 configured with a secure wlan and a guest wlan. The guest wlan is switching traffic at the wlc to a separate guest-wlan interface. When a guest is associated and authenticated, they can access the management console of the wlc which is in a different subnet. As I understand, the wlc does not route traffic. So how could this be happening? the guest subnet and the subnet the wlc management interface is in are different and separated by a firewall. I have also tried applying access lists in the wlc to each interface without luck. How can i stop the wlc from providing access to guest wlan users?
View 3 Replies View RelatedWe are implementing a new corporate headquarters and have bought a Cisco 5508. I have two connections plugged into the 5508 in ports 1 and port 2. Port 1 is for all internally wireless networks and connects to our core 6500 and use an external DHCP server scopes. Port 2 is for our guest WLAN and connects directly to a public network switch in front of (outside) the firewall. For the guest network, I have setup a vlan on the controller for dhcp and the interface setup to that vlan and dhcp scope built on the controller. how or can I NAT the internally addressing for the guest network to the public IP address on the controller. Essentially I want to drop of guest network traffic outside the firewall and not have to deal with setting up the firewall for any aspect of guest network traffic.
View 1 Replies View RelatedI have setup guest access on the controller and this is not working at the moment. DHCP server setup on the controller for the Guest users. You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
View 10 Replies View RelatedI have a wlc 5508 and I'd like to setup a network for visitors. They will connect to the WLAN, enter a password and then automatically get redirected to an external website. I understand the wlc 5508 supports this but I'm struggling to find out how to set this up I assume this can be done without having to customise webauth bundles?
View 2 Replies View RelatedI'm newbie in Networking. I want to establish a small WLAN network where all the laptops (6 laptops) can use WiFi Internet and also can print via a network printer.I have these hardwares:1: DSL Modem2: A Belkin F5D8233-4 300 Mbps router3: A Network printer (with RJ45 ethernet port, Not wireless printer)4: LAN Cable (if needed)5: Finally 6 Client Laptops
View 4 Replies View RelatedSo which one will be better to use for the better performance when we have 20 computers to connect in WLAN.
View 1 Replies View Related