We have a Cisco 2505 WLC which can support 5 Ap's based on license. Is there any limitation on the no. of ssid's that can be configured on a wlc, how to determine that detail.
View 5 Replies
What is the maximum number of WLANs/SSIDs that can be configured on a H-REAP access point? I have a network with 3502i AP's, centralised WLC's in the data centre running 7.0.116.0, and WCS version 7.0.172.0.
I was successfully running 2 SSID's at a remote site, one SSID was configured for H-REAP local switching, dropping out to the local site VLAN X, and the other SSID was a central switching guest WLAN anchored to a WLC in a DMZ.I configured a third SSID at the local site running H-REAP local switching, and now I cannot see the guest SSID anymore, it does not appear to be broadcasting.Is there a maximum of 2 WLANs/SSIDs when operating in H-REAP mode?
I have a question regarding to the maximmum number of active SSID's on a WLC 5500 with 3500i, it's my understanding that the 3500i can support 16 active SSID's is it the same when connected to the WLC? Also, if possible would the WLC shutdown un-used Radios or maybe after hours?
View 1 Replies View RelatedWe have a deployment of 400 store. Each of those have 2 GRE tunnels running over MPLS & 2 GRE Tunnels running over Internet leading to our 2 data-centers. At each Data-Center, we have 1 ASR-1002 connecting both MPLS & Internet MPLS tunnels (800 total per router).
I saw in the documentation that OER & PfR cannot support more than 20 external interface (in our case GRE tunnels) per MC. Does it means that we need to have 20 routers acting as MC to be able to use PfR for our Internet GRE tunnels ?
Is there any more scalable solution for this ? How big company address this issue when they have a lot of interface to run PfR ?
I have LMS3.2 running and have set up daily log rotation of my SYSLOG file via Common Services-Server-Admin-Log Rotation. In LMS2.6 I set this up from the command line and was able to set the number of rotations to 120. I found in LMS3.2 setting up the rotation via the GUI that the number of rotations is limited to 90.
View 1 Replies View Relatedour WAN is connected via L2WAN and using EIGRP to connect the sites. Currently there are 35 EIGRP neighbors over L2WAN and we are to install 15 more sites and will be connected to the same L2WAN. Some sites are still using Cisco 2651XM and we would like to know if it can still handle another 15 EIGRP neighbors. Some sites are 2800 and 2900 routers. And is there any other things to consider for EIGRP over L2WAN?
View 5 Replies View RelatedWe have 2 Hubs (Cisco 7200 - 2 for redudancy). Every customer have a Spoke (Cisco 881). The Spokes are 24/24 connected to the 2 hubs (2 dmvpn tunnels) to give us the access to our equipments of monitoring and for support. Every Spoke have a NAT table with a specific NAT range for every Spoke. Like this we can reach every devices with a unique IP inside the VPN.For example:
- Spoke_001 have a NAT IP range of 10.80.0.0 255.255.254.0
- Spoke_002 have a NAT IP range of 10.80.2.0 255.255.254.0
...
To connect to the hubs with our laptops, we are using the Cisco VPN client. We have different profiles created in the hubs:
- Admin profile with an ACL that allow the connectivity to every Spoke
- Integrator profiles: that allow the connectivity of one integrator to some defined Spokes.
So the integrator profile looks like this in the hub
crypto isakmp client configuration group [NAME]
key [PASSWORD]
domain [DOMAIN]
pool [NAME]
acl [NAME_VPN_Split]
[code]....
The problem is that if we can't summarize an ACL in less than 50 lines, we will have to create a second profile and to know wich one to use for wich network...
Version:
ROM: System Bootstrap, Version 12.3(4r)T3, RELEASE SOFTWARE (fc1)
BOOTLDR: 7200 Software (C7200-KBOOT-M), Version 12.3(15), RELEASE SOFTWARE (fc3)
System image file is "disk2:c7200-advsecurityk9-mz.151-4.M2.bin"
We have an ASA 5520 using for VPN & would like make use ASA's local CA to manage certificate.Do you know if there's any limitation on number of certificates that the local CA supports ?
View 6 Replies View RelatedI look after 5 sites in total.All sites are connected together via MPLS. Two of the sites, HQ1 and HQ2 are also connected together via 1Gb Metro so traffic is just switched between the 2 networks.EIGRP is fed into BGP to pass the routes between the sites with all sites in the same EIGRP AS.
All sites are configured with the same AS number (55555) and connect into the same service provider network so each site is connecting to a neighbor in the same AS (444).
I want all incoming traffic from the 3 sites to come in through HQ1 always. Can I influence the service provider's network to make sure this happens? Is this done via "set local-preference 20" on my side or do I have to get the service provider to make changes on their side too.
I set up my wireless clients to web authenticate against a RADIUS server as a second layer of security. However, everytime a machine goes to sleep or in a low power state, they have to reauth again. Is there any way to prevent this from happening on a 2505? I don't have a problem with wireless clients having to reauth every day, but multiple times a day can get annoying to users, especially with cell phones and tablets.
View 1 Replies View RelatedI am testing rogue on wire using 5508 WLC and , I have a dedicated AP configured as rogue detector and configured the switch port where the Rogue detector is connected as trunk. I have plugged in an autonomous AP with open authentication to the same switch so that it can act as a rogue. On the WLC, I can see that Autonomous AP as rogue on Wire. But along with that I am seeing another AP as rogue on wire, even though i have plugged in only one Autonomous AP to the switch.
View 3 Replies View RelatedI have a 1262 that will be setup as a WGB and wirelessly connect to a Cisco MESH AP. A switch and clients will hang off of the 1262 WGB. How many clients can a 1262 WGB support?
View 4 Replies View RelatedCustomer wants to place a single 1552E to cover a particular area in his campus, and it will be placed on a tower, and the question is concerning the height. I can not find any particular height limitation such as 5 meters, 10 meters, etc. I understand this will influence the sign propagation as well as throughtput to the users, but can not find a matrix or a best practice guide for that.
View 1 Replies View Relatedany information regarding height limitation for installing the above ceiling mounted antennas. And is there a separation between the 2 antennas when mounted in the ceiling.
View 6 Replies View Relatedaccess point and the limitation on the users connected to the SSID using a wireless lan controller. From the installation guide I see an incredible thing:
Supported User Count Only fifteen users are allowed to connect on the WLAN Controller WLANs provided on the 600 series at any one time. A sixteenth user cannot authenticate until one of the first clients de-authenticates or a timeout occurred on the controller. Note: This number is cumulative across the controller WLANs on the 600 series. For example, if two controller WLANs are configured and there are fifteen users on one of the WLANs, no users will be able to join the other WLAN on the 600 series at that time. This limit does not apply to the local private WLANs that the end user configures on the 600 series designed for personal use and clients connected on these private WLANs or on the wired ports do not affect these limits.
Is it possible a terrible limitation like this ?
I just installed a brand new AP541N-A-K9 (running AP541N-K9-2.0(1) software) and cannot seem to add a SSID. I've tried both from CCA and directly from the Web interface (Wireless:Wireless Network Setup menu). The Add Another button doesn't seem to do anything. I've even tried multiple browser versions.
View 1 Replies View RelatedI have a 4404 with 3 SSID's configured on it. I only want all SSID's to be available on one floor in one building and not on any other AP's in any other building or floor.I thought the way to do it was via AP group but have not had any luck getting that to work. I setup a group for the AP's that I do not want all SSID's and then assigned those AP's to that group. However, I can still see all three SSID's where I only want to see 2 SSID's.
View 4 Replies View RelatedI want to split the usage of the AP so that visitors are on their own wireless connnection and VLAN.We have 2 WAP4410N APs. One AP acts as a repeater for the another AP.They are both in 4.0.4.2 firmware.We are using WPA2 RADIUS authentication, and would like for visitors to use WPA2 PSK. Under Wireless tab, I have 1 SSID, but the other 3 available boxes for SSIDs are greyed out.When I click in them, they will not allow me to type an ID.I watched a video of how to add SSIDs and VLANs, and it looked simple enough.He just clicked in the box and was able to add more IDs.Could my current config be preventing me from adding additional SSIDs?
View 6 Replies View RelatedI have here a couple of APs with c1130-k9w7-mx.124-25d.JA1 loaded as firmware.
I want to configure them with 2 SSID: 1 encrypted, 1 public. Each should go to its own vlan, and thus should have a trunk towards the switch.
My wireless experience approaches zero however, and I cannot get the APs to even send out an unencrypted public SSID.
The config that is currently on the AP, after trying a lot of things is:
gibbs#show run
Building configuration...
Current configuration : 3272 bytes
!
version 12.4
[Code].....
I am trying to configure WLC 2504 with the following setup:
- three WLAN SSIDs
- management/ap-manager interface on VLAN 10
- guest WLAN on dynamic interface VLAN 20
- main WLAN on dynamic interface VLAN 30
- WLAN for tablet and smartphone devices VLAN 40
At this point switch trunking is configured and three WLANs are mapped to three dynamic different interfaces. I can see all associated APs (which are on the same subnet as management interface on VLAN 10), and can ping each of the APs as well as gateways on L3 switch Catalyst 3750-x. Also, on the WLC interface I see that all WLANs are enabled and SSIDs are set to broadcast, all AP radio is in 'up' mode. DHCPs are configured on management interface and on all dynamic interfaces. L3 switch gateways all have ip helper-address pointing to main DHCP. 'sh vlan' and 'sh int trunk' commands on the connected switches show correct settings.
However, I see absolutely no any SSIDs to connect to on any PC or Mac computer I tested.
We recently received our WLC 5508, AP and switches to setup our WLAN but I'm having trouble getting it all to work. It's been months since the course and I'm having trouble troubleshooting the problem.I've setup the WLC, AP and switches and I have network connectivity to all. The WLC see's my AP and I have all my WLAN and interfaces configured (SSID broadcast is enabled) but I still don't see any SSID coming from the AP.
View 23 Replies View RelatedIs it possible to configure two SSIDs with same valn (default VLAN) with same IP addressing subnet on an autonomous 1240AG access point ios ver is 12.4 21a ja1.
View 3 Replies View Relatedi used my 610N v2 for 2 years and recently i upgraded my network from 100mb to fiber 500mb , however, if i directly plug the lan cable to my computer , i can get full speed , but with 610N, the speed is limited to 130 for both upload and download .i had already upgrade my firmware and did factory reset, none of them work. Is it the limitation of the router ?
View 1 Replies View RelatedI have some tunnels which terminate to my home router. I'm allowing the other ends of the tunnels to use my voice setup. I need to prepend *67 to all called numbers which don't originate from my house. I don't want people calling my home number based on the caller-id number they see when someone across one of the tunnels calls.
So if 5008 calls 212-333-4444 I want it sent to my provider as *672123334444. If 5001 calls a number, I don't want it touched. Can I do this? I can use IOS or CUCM here.
We have a customer who is evaluating a Cisco Vs. Motorla wirless solution. He says that a Motorola AP can only work in standalone mode for 48 hrs. after it lost communication to the controller. Is there any limitation like this with a 2500 controller and 1140 series access points solution?. Is there any reference to show?
View 3 Replies View RelatedI need to configure a WAP4410N for use on a small, very simple business network. There should be a corporate WLAN and a guest WLAN. The corporate WLAN should allow anyone connectd to it to access resources on the domain.
In front of the WAP is a cable modem/router and a basic Level 2 (web managed) switch. What do i have to do to segregate the corporate and guest networks.
I thought I would add the corporate WLAN to VLAN1 (assuming the default VLAN in the switch is VLAN1). Then I figured I could create the guest WLAN and assign it to VLAN2 which which will be controlled entirely by the 4410N (DHCP, DNS, etc.) Does this sound like the right way of going about things?
I have several Aironet 1231 APs most running 12.3(8)JEA software. There are 4 SSIDs on (each in separate VLAN), with only one broadcasting (called pubwifi). The broadcasting one is an open, unencrypted network: [code] After adding another braodcasting SSID (encrypted, separate VLAN), I encountered weird situation: my WiFi clients are unable to connect to pubwifi. It is not showing in the available networks or is showing as an "unknow" network. New encrypted/bradcasting ssid is advertaising just fine.
View 6 Replies View RelatedCurrently my company has 1 primary SSID that is used throughout both floors of the building. We have 1252 LAPs which have 2.4 and 5Ghz antennas. I'm not sure if this issue is only with XP or perhaps it's the computer's drivers but we run into problems with end users going to a different location and having a very weak signal or nothing at all, yet coverage is fine. I believe the problem is the end user's machine selecting the strongest signal and it I have the feeling that switching bands isn't being done as it should when it's in range. So my question,
Should I split up our 1 SSID and created multiple SSIDs according to the location and include 5Ghz or 2.4Ghz in the SSID name so it's easier to ensure that users are connected to the proper signal? I want to ask if multiple SSIDs would still enable users to freely roam (as long as the ssids are configured) throughout the building without noticing a loss of signal but currently just having 1 SSID isn't really enabling people to freely roam around without connection issues.I don't believe having multiple SSIDs will be useful for the computer's choose their connection any more efficiently but allowing the user to manually see what they're connected to and pick something better according to their location.
I am running a WiFi network built on Cisco 1262 APs and Cisco WLC 5508. My APs broadcast two SSIDs, let call them "WiFi_Pay" and "WiFi_Free". I have a problem: when users migrate from "WiFi_Pay" to "WiFi_Free" (not moving, connecting to the same AP), the connection fails. If they try for second time, it is always successful. My task is to ensure that such migrations run smoothly and be successful from the first attempt.
View 2 Replies View RelatedI found a few older forum posts and documents online discussing how to create multiple SSIDs on 1 1252 AP using the WLC and they state that VLANs are needed for the interface and then I've read that multiple SSIDs on 1 interface are also possible. I'm not sure on how to actually configure this. I would like my 2.4Ghz radio on the 1252 to be associated with the current SSID in production and the 5Ghz band associated with another SSID that's in production. I couldn't find an option in the WLC or anything stated in the documents I've read about how to associate the radio band with the SSID.
View 5 Replies View RelatedDoing segregation of SSIDs Base on AP , I have the following scenario:
Head Office :
2 SSIDs (HO_WiFi , Guest) , Access Points which are working in connected mode and grouped on the default ap group .
Remote site:
2 SSIDs (Branch_Wifi , Guest) , Access Points working in flex connected mode and locally switching the traffic .
As shown above , I will be having Head Office , and other 20 Remote Sites with Access Points working in Flex connected mode. What is the best way to group AP and segregate SSID base on location. Above Scenario are build base on WLC 5508 and AP 1142.
I am trying to setup a RV180 and 3 wireless access points. I want the AP's to have 2 ssids that are isolated from each other. IE guest network and main network. I have setup VLAN's and my AP's support 802.1q and have ssid's with matching VID's. I was able to get this to work basically, but things seem to have gotten confusing when I plug the AP's into a POE switch instead of directly into the rv180. At this point I'm not sure exactly waht to ask. Maybe start by providing basic info on how I'm supposed to do this. I was under the impression that since both devices support 802.1q I could configure the VLANs on the router, and tell the AP's to apply a VID to the SSID and thing would work. This isn't the case unfortunately.
View 5 Replies View RelatedI am trying to provision three 1142 AP's so they broadcast multiple SSIDs. I have set the following commands, but I am not able to get more than one SSID to broadcast. As you can see I added the "guest-mode" command to one of the SSIDs which took it without problems. That other SSID does not accept the command.
dot11 ssid Test
vlan 2
authentication open
[Code].....
