Cisco Wireless :: 5508 / 1262 - Roaming Between Two SSIDs On Same AP
May 22, 2012
I am running a WiFi network built on Cisco 1262 APs and Cisco WLC 5508. My APs broadcast two SSIDs, let call them "WiFi_Pay" and "WiFi_Free". I have a problem: when users migrate from "WiFi_Pay" to "WiFi_Free" (not moving, connecting to the same AP), the connection fails. If they try for second time, it is always successful. My task is to ensure that such migrations run smoothly and be successful from the first attempt.
View 2 Replies
ADVERTISEMENT
Dec 2, 2012
I have the need to run a few autonomous APs (1262) for some sites on satellite links. At a bare minimum I need to run two WLANs. One is wide open, and the other with an ACL that heavily restricts access. Is there any way to tie two WLANs to a single VLAN, while applying an ACL to just one WLAN?
View 4 Replies
View Related
Jan 18, 2012
We recently received our WLC 5508, AP and switches to setup our WLAN but I'm having trouble getting it all to work. It's been months since the course and I'm having trouble troubleshooting the problem.I've setup the WLC, AP and switches and I have network connectivity to all. The WLC see's my AP and I have all my WLAN and interfaces configured (SSID broadcast is enabled) but I still don't see any SSID coming from the AP.
View 23 Replies
View Related
Dec 26, 2012
Doing segregation of SSIDs Base on AP , I have the following scenario:
Head Office :
2 SSIDs (HO_WiFi , Guest) , Access Points which are working in connected mode and grouped on the default ap group .
Remote site:
2 SSIDs (Branch_Wifi , Guest) , Access Points working in flex connected mode and locally switching the traffic .
As shown above , I will be having Head Office , and other 20 Remote Sites with Access Points working in Flex connected mode. What is the best way to group AP and segregate SSID base on location. Above Scenario are build base on WLC 5508 and AP 1142.
View 9 Replies
View Related
Jul 21, 2011
I have more different client networks with one ssid, when a client is in another network gets an ip it still from the old network.
How can I to the wlc change this so he gets one right address. I have a Cisco WLC 5508 and 1262/1252 Access point
View 6 Replies
View Related
Feb 12, 2013
I have an issue where I have an AP in one room and another in another.When I walk from one room to the other, I lose signal but manages to see the SSID and join.But, I cannot seem to surf the Internet, I have to manually disconnect and reconnect. Normal wireless routers I reconnect seamlessly without any manual disconnect & reconnect.Currently using cisco 5508 and ap2600.
View 8 Replies
View Related
Apr 7, 2011
Currently have a 5508 in the lab and testing 4 AP's with it. Eventually there will be 18 AP's spread thru out different floor in our building.
So far access is working fine using WPA, 802.1x and the client configured to use windows logon credentials..But it doesn't seem to automatically transfer between access points.
View 1 Replies
View Related
Aug 26, 2012
We have a 5508 controller with about 40 LAPs, running AIR-CT5500-K9-7-2-103-0-FUS software.The need has arose to have LAPs in various locations that only broadcast specific SSIDs.
I've got seperate dyanmic interfaces already created.We have 3 "Normal" SSIDs that we broadcast to the LAPs already associated with the 5508.2 more SSIDs were created (2 different purposes).
I just can't figure out how to get it to certain LAPs to only broadcast the specific SSIDs, while the rest broadcast the normal 3, but not those 2 new ones.
View 13 Replies
View Related
May 27, 2013
I am having some troubles with client roaming on a 5508 controller running firmware 7.3.101.0. As soon as a client roams outside the range of an AP they lose data flow and do not seem to transition to another AP for about 1 minute.This is a small network with 6 x AIRCAP3502E-N-K9 AP's (running in H-REAP mode) on the same floor and clients are a mix of HP notebooks, Mac Books, iMacs, iPads and iPhones. There are several seperate SSID's setup and the problem occurs on all. All are WPA2/AES with either a PSK or 802.1X. Both 2.4GHz and 5GHz radios are enabled with auto power and channel selection.
I have tried changing the roaming settings from default and also playing with the AP power settings to no avail.Is this normal behaviour or is there something I can do to improve the reconnection speed?
View 11 Replies
View Related
Nov 27, 2011
I have two 5508, no anchor, only one SSID with internal web authentication using radius server.Under "Configuring Mobility Groups", Cisco guide says: "If a client roams in web authentication state, the client is considered as a new client on another controller instead of considering it as a mobile client".
I understand that if a client that has already autheticated via web roams between two LAPs that are associated with different WLCs, it has to reathenticate.
View 6 Replies
View Related
Jun 3, 2013
Since two months they work full time with the new Dutch Electronic Patient Dossier.We installed 3 Cisco 5508 controllers, version 7.0.230.0 last year on a HP-switched network on a layer 2 mobility domain.Cisco 1041 AP are
The personnel works woth thin clients url... The one with the double antenna.This client has a Broadcom BCM943228HM4L 802.11 a.b.g.n (2x2) adapter.
On the client they have a connected RDP session to a server with the documents.Now they are walking from one patient to another patient. The problem they experience is a very late roaming. At the beginning of the corridor, the client will associate, but is going to roam at the end of the corridor. We installed 4 AP's on each corridor, so they signal is very well, maybe to well?
I disabled client loadbalancing and band select.The lowest data rates are also disabled. Mandatory begins at 12 Mbps. I can increase this to 18 Mbps.These clients work with PSK, with both methods (WPA-TKIP and WPA2-AES) enabled.We did this because of many old and new clients.
The customer tried to find out the problem with a smartphone, same issue. Very late roaming.I can upgrade the WLC to 7.0.240.0. The only problem I have is the WCS. When upgrading to 7.2 and higher I need to have NCS.
View 1 Replies
View Related
Apr 29, 2013
I have a device manufacture there are requesting the following change on a customer's WLC 5508.
-config advanced eap identity-request-timeout 60
-config advanced eap request-timeout 60
I have studied many guides but I can't find out if there is a down-side to setting the timeout this high.Could it result in slow roaming or re-authentication if there is a connection error? The customer have large areas with high client density and some outdoor areas with low client density.
View 3 Replies
View Related
Jun 26, 2012
Is there any additional configuration to be done on the 5508 WLC for Wireless Laptop / Voice Roaming? I tested with Wireless IP Phone and found some blankness in voice , whereas i have other access point nearby , which wasn't switching over easily .
View 3 Replies
View Related
Apr 23, 2012
I'm trying to figure out if it is possible to configure in one site a wireless setup that goes like this:
One WLC (5508), multiple LAP's in H-REAP mode.
AP's will be splitted in multiple VLAN's belonging to different departments but with the same SSID.Each VLAN will have it's own DHCP scope. All AP's are located in the same site and I need to know if it is possible to roam between AP's that belong to different departments?
View 3 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
Feb 5, 2013
I have a customer that wants to restrict SSIDs that groups get based on their AD credentials. Currently, he is using Windows 2008 Radius Server and AD with Cisco 5508 WLCs. I found examples that shows this is possible but my question is if I have 2 user groups (teachers and students) in AD and apply a policy for the Radius to send SSID x to teachers and SSID y to students. Upon successfully authentication, would this deny teachers access to SSID y and students access to SSID x?
View 10 Replies
View Related
May 13, 2013
I am trying to build a new network from scratch, I have the WLC 5508 w/ Aironet 3600e APs connected to my Netgear Smart Switches and a Linksys RV082 router that I'm using as my DHCP server with several VLANs for several stuff on my Switches.
I have 2 questions:
1. Can I have 5 Interfaces configured on 5 different VLANs, each SSID on each a different Port:
Port 1: Controller management only=> 192.168.x.x /24
Port 2: SSID 1: WiFi Internal=> 172.16.x.x/12 (Radius Auth with no sharing)
Port 3: SSID 2: WiFi Internal w/ sharing=> 192.168.x.x/24 (Radius Auth with sharing)
Port 4 :SSID 3: WiFi Guest=> 10.0.x.x/8 (Web Auth)
Port 5: SSID 4: WiFi IT=> 192.168.x.x/24 ( Radius or certificate Auth with access to the controller management interface)
2. How can I use the Controller as the DHCP server for all the WiFi traffic, and how should that be configured to work with my other DHCP server?
View 3 Replies
View Related
Mar 13, 2012
Is it possible to convert autonomous access point Cisco 1262 to LAP?
View 9 Replies
View Related
Feb 28, 2012
I just installed a brand new AP541N-A-K9 (running AP541N-K9-2.0(1) software) and cannot seem to add a SSID. I've tried both from CCA and directly from the Web interface (Wireless:Wireless Network Setup menu). The Add Another button doesn't seem to do anything. I've even tried multiple browser versions.
View 1 Replies
View Related
Aug 2, 2012
I have a 1262 that will be setup as a WGB and wirelessly connect to a Cisco MESH AP. A switch and clients will hang off of the 1262 WGB. How many clients can a 1262 WGB support?
View 4 Replies
View Related
Jun 7, 2012
We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
View 12 Replies
View Related
Oct 20, 2011
Do I need to plug in AP 1262 into a PoE switch or external power adapter before can power on? How about LAP 1262? Do I need PoE switch as well?
View 4 Replies
View Related
May 9, 2012
I have new 1262 APs, this have Gig Interface, when I connect the AP in my 6500 with PoE Gig Interface, the AP turn on, but the interface never get up. I need to change the speed to 100 in the 6500 switch port, when I do this, the interface become UP.
This is the model of the card WS-X6148A-GE-45AF This is the Switch IOS s3223-ipservicesk9_wan-mz.122-18.SXF11.bin
The controller is 5500 version 7.2
This is the interface config:
interface GigabitEthernet4/36
switchport
switchport access vlan 308
[Code].....
View 5 Replies
View Related
Apr 1, 2012
I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
View 1 Replies
View Related
Aug 19, 2012
I have to replace a 1230 with an 1262 AP.
All antennas have to be in the same direction on the AP and I guess when the old 1230 is working well the 1262 will be only better . Attached u see how I plan to mount the new AP versus the old one...
View 7 Replies
View Related
Sep 8, 2012
Our scenario requires some customization in Wireless network. We have moving Forklift machines fitted with network devices. The network device in forklift acts as a client. But it doesn't have a wireless adapter and no provisions to add a wireless adapter. There is one ethernet port.
So we have a plan to attach one AP(1262) to each forklift. this AP needs to talk to the AP whcih is connected to Wired network. The network deivce in the forklift need to talk to the root AP(1262) through the AP directly connected to it over Ethernet.
View 5 Replies
View Related
Jun 6, 2012
We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC.
The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL]
Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
View 3 Replies
View Related
Jan 13, 2013
I'm having this weird problem with an IP phone behind a WGB. The setup is like this: Cisco controller -> Switch -> switch -> AP (Air LAP1142) -> WGB (Air LAP 1262) -> switch -> IP phone.
The phone works, sometimes. Sometime for days, sometime for hours, then it disconnects and what I have to do then to get it working again is to run this command on the bridge. "no workgroup-bridge unified-vlan-client", then wait for it to disassociate, then run "workgroup-bridge unified-vlan-client" and after that it gets a stable connection (for a undetermined amount of time).
Here´s the WGB config:
version 15.2
no service pad
service timestamps debug datetime msec
[Code]....
View 5 Replies
View Related
Mar 22, 2009
I have a 4404 with 3 SSID's configured on it. I only want all SSID's to be available on one floor in one building and not on any other AP's in any other building or floor.I thought the way to do it was via AP group but have not had any luck getting that to work. I setup a group for the AP's that I do not want all SSID's and then assigned those AP's to that group. However, I can still see all three SSID's where I only want to see 2 SSID's.
View 4 Replies
View Related
Mar 29, 2012
I want to split the usage of the AP so that visitors are on their own wireless connnection and VLAN.We have 2 WAP4410N APs. One AP acts as a repeater for the another AP.They are both in 4.0.4.2 firmware.We are using WPA2 RADIUS authentication, and would like for visitors to use WPA2 PSK. Under Wireless tab, I have 1 SSID, but the other 3 available boxes for SSIDs are greyed out.When I click in them, they will not allow me to type an ID.I watched a video of how to add SSIDs and VLANs, and it looked simple enough.He just clicked in the box and was able to add more IDs.Could my current config be preventing me from adding additional SSIDs?
View 6 Replies
View Related
Jun 15, 2012
I have here a couple of APs with c1130-k9w7-mx.124-25d.JA1 loaded as firmware.
I want to configure them with 2 SSID: 1 encrypted, 1 public. Each should go to its own vlan, and thus should have a trunk towards the switch.
My wireless experience approaches zero however, and I cannot get the APs to even send out an unencrypted public SSID.
The config that is currently on the AP, after trying a lot of things is:
gibbs#show run
Building configuration...
Current configuration : 3272 bytes
!
version 12.4
[Code].....
View 4 Replies
View Related
Jul 16, 2012
I am trying to configure WLC 2504 with the following setup:
- three WLAN SSIDs
- management/ap-manager interface on VLAN 10
- guest WLAN on dynamic interface VLAN 20
- main WLAN on dynamic interface VLAN 30
- WLAN for tablet and smartphone devices VLAN 40
At this point switch trunking is configured and three WLANs are mapped to three dynamic different interfaces. I can see all associated APs (which are on the same subnet as management interface on VLAN 10), and can ping each of the APs as well as gateways on L3 switch Catalyst 3750-x. Also, on the WLC interface I see that all WLANs are enabled and SSIDs are set to broadcast, all AP radio is in 'up' mode. DHCPs are configured on management interface and on all dynamic interfaces. L3 switch gateways all have ip helper-address pointing to main DHCP. 'sh vlan' and 'sh int trunk' commands on the connected switches show correct settings.
However, I see absolutely no any SSIDs to connect to on any PC or Mac computer I tested.
View 2 Replies
View Related
Mar 18, 2013
Is it possible to configure two SSIDs with same valn (default VLAN) with same IP addressing subnet on an autonomous 1240AG access point ios ver is 12.4 21a ja1.
View 3 Replies
View Related