Cisco Wireless :: Power Input For AP 1262?
Oct 20, 2011Do I need to plug in AP 1262 into a PoE switch or external power adapter before can power on? How about LAP 1262? Do I need PoE switch as well?
View 4 Replies
ADVERTISEMENT
Cisco Wireless :: 1262 Maximum Transmit Power
Jun 10, 2012I will be doing a site survey using the client's Cisco 1262 with only 1 radio (g/n), 3 antennas. What is the maximum transmit power, 20dBm or 23dBm? I need to set the transmit power in the Airmagnet to 50% or 3dBm down as recommended by Cisco.
View 4 Replies View RelatedD-Link DIR-615 :: Low Input Voltage Not Connecting Power Light Ok
Dec 18, 2011My Dir-615 stopped working some weeks ago and I switched to another router until I had time to look at it. Tonight I checked the ps voltage and it read exactly +5v but just for a test I tried another 5v ps (which tested a little higher) and it worked. The ps that works reads about link +7vdc. Before this the power light came on with the occasional blink but I could't connect.
View 5 Replies View RelatedCorrect Polarity Of Power Input Plug For Vigor110 Modem?
Mar 6, 2012What is the correct polarity of the power input plug for vigor110 modem?I know it should be 9volts but which part of the plug should be positive? Original power supply gone missing and no indication on unit of plug setting.
View 5 Replies View RelatedCisco Wireless :: 1262 AP Convert To LAP?
Mar 13, 2012Is it possible to convert autonomous access point Cisco 1262 to LAP?
View 9 Replies View RelatedCisco Wireless :: 1262 WGB Client Limitation
Aug 2, 2012I have a 1262 that will be setup as a WGB and wirelessly connect to a Cisco MESH AP. A switch and clients will hang off of the 1262 WGB. How many clients can a 1262 WGB support?
View 4 Replies View RelatedCisco Wireless :: AP 1262 Cannot Join WLC 4402
Jun 7, 2012We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
Cisco Wireless :: AP 1262 Don't Negotiate With Gig Interface
May 9, 2012I have new 1262 APs, this have Gig Interface, when I connect the AP in my 6500 with PoE Gig Interface, the AP turn on, but the interface never get up. I need to change the speed to 100 in the 6500 switch port, when I do this, the interface become UP.
This is the model of the card WS-X6148A-GE-45AF This is the Switch IOS s3223-ipservicesk9_wan-mz.122-18.SXF11.bin
The controller is 5500 version 7.2
This is the interface config:
interface GigabitEthernet4/36
switchport
switchport access vlan 308
[Code].....
Cisco Wireless :: To Join 1262 With Wlc 2100
Apr 1, 2012I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
View 1 Replies View RelatedCisco Wireless :: 1262 - Antenna Direction On AP?
Aug 19, 2012I have to replace a 1230 with an 1262 AP.
All antennas have to be in the same direction on the AP and I guess when the old 1230 is working well the 1262 will be only better . Attached u see how I plan to mount the new AP versus the old one...
Cisco Wireless :: 1262 - Acting As Client To Another AP?
Sep 8, 2012Our scenario requires some customization in Wireless network. We have moving Forklift machines fitted with network devices. The network device in forklift acts as a client. But it doesn't have a wireless adapter and no provisions to add a wireless adapter. There is one ethernet port.
So we have a plan to attach one AP(1262) to each forklift. this AP needs to talk to the AP whcih is connected to Wired network. The network deivce in the forklift need to talk to the root AP(1262) through the AP directly connected to it over Ethernet.
Cisco Wireless :: AP 1262 Cannot Join WLC 4402
Jun 6, 2012We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC.
The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL]
Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
Cisco Wireless :: WGB With Air LAP 1262 Disconnects After Some Days
Jan 13, 2013I'm having this weird problem with an IP phone behind a WGB. The setup is like this: Cisco controller -> Switch -> switch -> AP (Air LAP1142) -> WGB (Air LAP 1262) -> switch -> IP phone.
The phone works, sometimes. Sometime for days, sometime for hours, then it disconnects and what I have to do then to get it working again is to run this command on the bridge. "no workgroup-bridge unified-vlan-client", then wait for it to disassociate, then run "workgroup-bridge unified-vlan-client" and after that it gets a stable connection (for a undetermined amount of time).
Here´s the WGB config:
version 15.2
no service pad
service timestamps debug datetime msec
[Code]....
Cisco Wireless :: 1252 - WCS Reports AP Draws Low Power - With Correct Power Injector
Jul 21, 2011I keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.
Cisco Wireless :: Aironet 1262 Would Distance Be A Barrier
Oct 11, 2011is the aironet 1262 access point a good choice for an environment of about 20 users. each users is in an office and we are looking at deploying the ap at the end of the hall on a wall mount. would distance be a barrier and are there any better options out there?
View 3 Replies View RelatedCisco Wireless :: Using 1262 AP In Workgroup Bridge Mode?
Nov 18, 2012Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perform this functions? I will put a Layer 3 switch on both ends to route traffic (3560C-8). Should I use the Yagi antenna's for outdoor use?
View 1 Replies View RelatedCisco Wireless :: 1262 / 3500 For WLAN Between Buildings?
Jul 4, 2012I currently have WLC 5508 and a few campuses with LAP 1142, each with 2-3 vlan. Now one of our campuses have a building thas is a bit far away and needs network (wired). We can't get fiber or TP-cable there in a good way. So the plan is to get two 1262 or 3500 with AIR-ANT5160NP-R antennas and get a wireless link working between the campus and the building. And then connect one of the AP's to a switch in the other building to provide it with wired network.
The problem is that I can't find information on how to do it. Should both APs be in autonomus mode? I probably only need to have 1 VLAN in the other building but I am not sure yet. Is there a problem with transfering several VLAN over the WLAN-link?
Cisco Wireless :: 1262 AP / 2504 WLC - Only One Radio Appears?
Aug 12, 2012We have 6 1262 APs and a 2504 WLC. 5 of the 1262 appear correctly with 2 radios. One of them shows 1 radio. See screen shots below showing model numbers and interfaces on the AP with one radio available (All other 1262s show 2 radios as normal). Tried resetting the AP to factory default, but same result. Do I have a defective AP?
View 3 Replies View RelatedCisco Wireless :: Can C1200 Antennas Work On 1262
Mar 21, 20121. Can the C1200 antennas work on the 1262 ?
2. Can the 2.4Ghz antenna work on the 5Ghz ports on the 1262 ?
3. The 1262 has 6 antenna ports (3 2.4ghz and 3 5ghz), can the (3) 2.4 Ghz antenna be used only as i only have antennas for the C1200 Access point which are 2.4 Ghz.
Cisco Wireless :: 12dBi Mast Mount On 1262 AP
Sep 12, 2012I want to replace existing 1242s with 1262s. Which are currently in a Heated Nema Enclosures with 12dBi Mast Mount AIR-ANT24120. The 5.0 Ghz Radio is off. So the question is can I use the same Antennas AIR-ANT24120 for the new 1262? I’m assuming yes as long I use connectors A & C are tx/rx; on the center would we leave open or put a rubber duck on it?
View 3 Replies View RelatedCisco Wireless :: 1262 AP Doesn't Register With WLC4404
Oct 15, 2012We currently have about 50 Cisco 1252 wireless access points running from a 4404 Wireless LAN controller. We need to order more APs, but of course the 1252s have been discontinued.Was assured by Cisco that the 1262 would work just fine with our WLC. I'm messing around with a trial 1262 and am running into problems.We hard-code the IP address, hostname, default gateway, and controller IP address in each of our access points. I did that with the new 1262 the same way I did with the 1252s:lwapp ap ip address lwapp ap ip default-gateway etc., etc.That didn't work. Then I tried doing the same thing using (not sure if this is the correct terminology...) the capwap commands.
The AP still doesn't show up on the WLC's GUI, though I can ping the AP from the WLC and I can ping the WLC from the AP.I also can't use a web browser to get into the access point's configuration tool. Do I understand correctly that the lightweight APs don't have the GUI?
Cisco Wireless :: 1262 Indoor And Outdoor Antennas On Same AP?
Jun 19, 2012I have a metal shop that needs wireless indoors and outdoors.
Will it work if I mount the 1262 inside with 4 indoor antennas mounted inside the building and 2 outdoor antennas mounted outside?
Cisco Wireless :: LAP-1262 To C2504 Join Loop?
Mar 18, 2013i have two 1262 one is join ok but one join loop
View 7 Replies View RelatedCisco Wireless :: 5508 / 1262 - Roaming Between Two SSIDs On Same AP
May 22, 2012I am running a WiFi network built on Cisco 1262 APs and Cisco WLC 5508. My APs broadcast two SSIDs, let call them "WiFi_Pay" and "WiFi_Free". I have a problem: when users migrate from "WiFi_Pay" to "WiFi_Free" (not moving, connecting to the same AP), the connection fails. If they try for second time, it is always successful. My task is to ensure that such migrations run smoothly and be successful from the first attempt.
View 2 Replies View RelatedCisco Wireless :: 1262 - AP Not Connecting In Mesh Mode
Dec 22, 2012We have a few 1500 outdoor mesh ap's. 1262N are used to link to these 1500 and extend the coverage to places. All 1262 was configured as mesh. But upon installation, none of them actually register to the controller and join the other mesh ap's. They should be joining to the 1500's.
On testing, the 1500 joins the 1262N as mesh. however the 1262N does not join the 1500 as mesh even though the distance is less than 20m.
Cisco Wireless :: 1262 AP Antenna Cable Length Extension?
Apr 1, 2012providing an extension for the below antennas cable length for project related requirements with the AP 1262.
AIR-ANT2506 2.4 GHz, 5.2 dBi Mast Mount Omni Ant w/RP-TNC Connector
AIR-ANT5160V-R 5GHz 6dBi Omni Antenna w/RP-TNC connector
Cisco Wireless :: Clients Supported By Light Weight AP 1262?
May 29, 2012Recently, our company wireless AP 1262 connected more than 40+ clients, and sometimes the wireless access speed is too slow. those clients are only for MES data transfer, the date no more than 10K of each stations. So I'd like to know if the one AP can support the network traffic if whole testers transfer the data to Database via this wireless AP1262? and the WLC no clients roaming option for which clients can connect to another AP around. I have checked the WLC and AP configuration. no option for clients roaming to another APs, do you know how to configure this AP's Clients move to another APs?If we setup the new APs in the location, does the clients will be auto connect to this new AP?
View 7 Replies View RelatedCisco Wireless :: 1262 - AP Mode Change And Its No Longer Online
Jan 9, 2013We have a 1262 which was loaded with some recovery image for testing. After this, it doesn't get registered to the wireless controller.
we tried moving it back to autonomous mode and then again back to lightweight to have it join the controller. But it doesnt join the controller, debugs on the devices does not show any logs.
Cisco :: Wireless AP 1262 Getting Packet Drops While Buffering Videos
Apr 2, 2013We are having 1262 Access point model and we are getting packet drops when 20 users are connected and users do Video streaming and buffering online.
Even our AD IP address also getting packet drops during the users are connected and using youtube or someother video sites.
Cisco Wireless :: Some Devices Are Failing To Connect To Aironet 1262 AP
Jun 10, 2013Some devices are failing to connect to my Cisco Aironet 1262 AP. So far I have noted the ipad 2, a windows 8 phone and a bang and olufson speaker. Is there something I need to tweak in my config. Other devices connect fine, that is my laptop, desktop and android phone.
View 2 Replies View RelatedCisco Wireless :: Mixing And Connecting 1262 With 2600 And 3600
Apr 23, 2013I am don't need anything unusual and I would love to go with the 2600/3600 APs, unless mixing them up is a problem.
View 2 Replies View RelatedCisco Wireless :: Maximum Clients Supported By Aironet 1262 AP?
Jan 9, 2013How many maximum clients are supported by cisco aironet 1262 AP and also by a 5500 Wireless Controller?
View 4 Replies View RelatedCisco Wireless :: 1262 / Crossing The Radios In Repeater Mode
May 16, 2013I'm trying to configure Cisco 1262 AP's to allow me to use the 2.4 gHz radio for client access and the 5.x radio for the repeater connection back to a root AP connected to a LAN.
I have already configured the AP's to associate with each other via the 5.x radio, and have a client connected to the repeater AP via the 2.4 gHz radio. From my laptop on the LAN, I can connect to the repeater AP, but I cannot ping nor otherwise communicate with the distant client.
When I use the 2.4 gHz radio for repeater mode, clients that connect to the repeater AP can be seen and communicated with.Is there something special that needs to be done to get my desired scenario to work?All radios are members of bridge group 1.