Cisco Wireless :: 12dBi Mast Mount On 1262 AP
Sep 12, 2012
I want to replace existing 1242s with 1262s. Which are currently in a Heated Nema Enclosures with 12dBi Mast Mount AIR-ANT24120. The 5.0 Ghz Radio is off. So the question is can I use the same Antennas AIR-ANT24120 for the new 1262? I’m assuming yes as long I use connectors A & C are tx/rx; on the center would we leave open or put a rubber duck on it?
View 3 Replies
ADVERTISEMENT
Mar 22, 2013
I am still new to wireless. I have been studing for my CCNA Wireless for about 6 months now so I still have a lot of questions.
Right now I have to deploy some new APs. We are using 3502e APs. I have a qustion on how to mount antennas for these access points. I have to make a mounting bracket the new installations. What was done with the previous APs was to mount a unistrut beam to an I beam in the building. There is 2 AIR-ANT-1728's and 2 AIR-ANT-5160V-R antennas mounted straight out on the unistrut. Then they put a T bracket on the unistrut and mounted a second bar 90 degrees from the main bar and connected the third 1728 and 5160 antennas on the second mounting bracket. So we have 4 antennas in a row, and two off to the side 90 degrees from the other 4 antennas.
My question, is this OK to have them this way, or would it be better to have all 6 antennas in a straight line when I fabricate my new AP brackets?
Here is a picture of what I am talking about. This would be looking at it from above.
Current New Proposal
__________o__o__o__o_ _________o__o__o__o__o__o
| AP AP
|
|o
|
|o
View 7 Replies
View Related
Apr 26, 2012
I am looking for a wall mount bracket reference, for these 2 models of antennas :
- AIR-ANT5160V-R
- AIR-ANT2506
Something like that :I was not able to find any reference in cisco product list.
View 9 Replies
View Related
Mar 14, 2011
what's the best antenna arrangement for wall mounting the WAP4410N?I see pictures of the antennas for desk mount but nothing for a wall or ceiling mount.Should I just fiddle with them and see what works best?
View 3 Replies
View Related
Jan 10, 2013
I have a question if your Cisco 800 series wireless in a rack mount installation in racks to place the signal strength materials very well ?
View 0 Replies
View Related
Sep 13, 2011
I'm thinking to buy a E2500 router for my house. Is it possible to wall mount it?
View 7 Replies
View Related
May 10, 2012
Can the EA4500 be wall mounted? I don't see any provisions on the underside EA4500 to support securing to a wall.
View 9 Replies
View Related
Jan 4, 2012
Is there a wall mount bracket for the E2500 or is there a way of attaching this to a wall.
View 1 Replies
View Related
Mar 13, 2012
Is it possible to convert autonomous access point Cisco 1262 to LAP?
View 9 Replies
View Related
Aug 2, 2012
I have a 1262 that will be setup as a WGB and wirelessly connect to a Cisco MESH AP. A switch and clients will hang off of the 1262 WGB. How many clients can a 1262 WGB support?
View 4 Replies
View Related
Jun 7, 2012
We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
View 12 Replies
View Related
Oct 20, 2011
Do I need to plug in AP 1262 into a PoE switch or external power adapter before can power on? How about LAP 1262? Do I need PoE switch as well?
View 4 Replies
View Related
May 9, 2012
I have new 1262 APs, this have Gig Interface, when I connect the AP in my 6500 with PoE Gig Interface, the AP turn on, but the interface never get up. I need to change the speed to 100 in the 6500 switch port, when I do this, the interface become UP.
This is the model of the card WS-X6148A-GE-45AF This is the Switch IOS s3223-ipservicesk9_wan-mz.122-18.SXF11.bin
The controller is 5500 version 7.2
This is the interface config:
interface GigabitEthernet4/36
switchport
switchport access vlan 308
[Code].....
View 5 Replies
View Related
Apr 1, 2012
I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
View 1 Replies
View Related
Aug 19, 2012
I have to replace a 1230 with an 1262 AP.
All antennas have to be in the same direction on the AP and I guess when the old 1230 is working well the 1262 will be only better . Attached u see how I plan to mount the new AP versus the old one...
View 7 Replies
View Related
Sep 8, 2012
Our scenario requires some customization in Wireless network. We have moving Forklift machines fitted with network devices. The network device in forklift acts as a client. But it doesn't have a wireless adapter and no provisions to add a wireless adapter. There is one ethernet port.
So we have a plan to attach one AP(1262) to each forklift. this AP needs to talk to the AP whcih is connected to Wired network. The network deivce in the forklift need to talk to the root AP(1262) through the AP directly connected to it over Ethernet.
View 5 Replies
View Related
Jun 6, 2012
We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC.
The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL]
Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
View 3 Replies
View Related
Jan 13, 2013
I'm having this weird problem with an IP phone behind a WGB. The setup is like this: Cisco controller -> Switch -> switch -> AP (Air LAP1142) -> WGB (Air LAP 1262) -> switch -> IP phone.
The phone works, sometimes. Sometime for days, sometime for hours, then it disconnects and what I have to do then to get it working again is to run this command on the bridge. "no workgroup-bridge unified-vlan-client", then wait for it to disassociate, then run "workgroup-bridge unified-vlan-client" and after that it gets a stable connection (for a undetermined amount of time).
Here´s the WGB config:
version 15.2
no service pad
service timestamps debug datetime msec
[Code]....
View 5 Replies
View Related
Oct 11, 2011
is the aironet 1262 access point a good choice for an environment of about 20 users. each users is in an office and we are looking at deploying the ap at the end of the hall on a wall mount. would distance be a barrier and are there any better options out there?
View 3 Replies
View Related
Nov 18, 2012
Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perform this functions? I will put a Layer 3 switch on both ends to route traffic (3560C-8). Should I use the Yagi antenna's for outdoor use?
View 1 Replies
View Related
Jun 10, 2012
I will be doing a site survey using the client's Cisco 1262 with only 1 radio (g/n), 3 antennas. What is the maximum transmit power, 20dBm or 23dBm? I need to set the transmit power in the Airmagnet to 50% or 3dBm down as recommended by Cisco.
View 4 Replies
View Related
Jul 4, 2012
I currently have WLC 5508 and a few campuses with LAP 1142, each with 2-3 vlan. Now one of our campuses have a building thas is a bit far away and needs network (wired). We can't get fiber or TP-cable there in a good way. So the plan is to get two 1262 or 3500 with AIR-ANT5160NP-R antennas and get a wireless link working between the campus and the building. And then connect one of the AP's to a switch in the other building to provide it with wired network.
The problem is that I can't find information on how to do it. Should both APs be in autonomus mode? I probably only need to have 1 VLAN in the other building but I am not sure yet. Is there a problem with transfering several VLAN over the WLAN-link?
View 3 Replies
View Related
Aug 12, 2012
We have 6 1262 APs and a 2504 WLC. 5 of the 1262 appear correctly with 2 radios. One of them shows 1 radio. See screen shots below showing model numbers and interfaces on the AP with one radio available (All other 1262s show 2 radios as normal). Tried resetting the AP to factory default, but same result. Do I have a defective AP?
View 3 Replies
View Related
Mar 21, 2012
1. Can the C1200 antennas work on the 1262 ?
2. Can the 2.4Ghz antenna work on the 5Ghz ports on the 1262 ?
3. The 1262 has 6 antenna ports (3 2.4ghz and 3 5ghz), can the (3) 2.4 Ghz antenna be used only as i only have antennas for the C1200 Access point which are 2.4 Ghz.
View 1 Replies
View Related
Oct 15, 2012
We currently have about 50 Cisco 1252 wireless access points running from a 4404 Wireless LAN controller. We need to order more APs, but of course the 1252s have been discontinued.Was assured by Cisco that the 1262 would work just fine with our WLC. I'm messing around with a trial 1262 and am running into problems.We hard-code the IP address, hostname, default gateway, and controller IP address in each of our access points. I did that with the new 1262 the same way I did with the 1252s:lwapp ap ip address lwapp ap ip default-gateway etc., etc.That didn't work. Then I tried doing the same thing using (not sure if this is the correct terminology...) the capwap commands.
The AP still doesn't show up on the WLC's GUI, though I can ping the AP from the WLC and I can ping the WLC from the AP.I also can't use a web browser to get into the access point's configuration tool. Do I understand correctly that the lightweight APs don't have the GUI?
View 4 Replies
View Related
Jun 19, 2012
I have a metal shop that needs wireless indoors and outdoors.
Will it work if I mount the 1262 inside with 4 indoor antennas mounted inside the building and 2 outdoor antennas mounted outside?
View 5 Replies
View Related
Mar 18, 2013
i have two 1262 one is join ok but one join loop
View 7 Replies
View Related
May 22, 2012
I am running a WiFi network built on Cisco 1262 APs and Cisco WLC 5508. My APs broadcast two SSIDs, let call them "WiFi_Pay" and "WiFi_Free". I have a problem: when users migrate from "WiFi_Pay" to "WiFi_Free" (not moving, connecting to the same AP), the connection fails. If they try for second time, it is always successful. My task is to ensure that such migrations run smoothly and be successful from the first attempt.
View 2 Replies
View Related
Dec 22, 2012
We have a few 1500 outdoor mesh ap's. 1262N are used to link to these 1500 and extend the coverage to places. All 1262 was configured as mesh. But upon installation, none of them actually register to the controller and join the other mesh ap's. They should be joining to the 1500's.
On testing, the 1500 joins the 1262N as mesh. however the 1262N does not join the 1500 as mesh even though the distance is less than 20m.
View 6 Replies
View Related
Dec 5, 2012
anybody with 2 x rack mount kits for a SRW208P that they don't want? I need to rack mount these devices but my predecessor very wisely decided to throw them out and Cisco does not sell the racks as a separate SKU.
View 1 Replies
View Related
Nov 22, 2011
I need to install a AIR-AP1231G in one of our facilities. Its desired location is on a 1" thick solid steal wall filled with concrete. I thought maybe mounting it with a magnet would be easier than tap and die. Any reason I shouldn't use a high powered magnet to mount it with?
View 3 Replies
View Related
Dec 13, 2011
Any replacement bracket or some other way to easily mount the 942l in a window? i have a long window next to my front door i want to just stick this someone about shoulder high in that window looking right to the door so will see anyone who comes.
View 5 Replies
View Related
Apr 1, 2012
providing an extension for the below antennas cable length for project related requirements with the AP 1262.
AIR-ANT2506 2.4 GHz, 5.2 dBi Mast Mount Omni Ant w/RP-TNC Connector
AIR-ANT5160V-R 5GHz 6dBi Omni Antenna w/RP-TNC connector
View 4 Replies
View Related