Cisco Wireless :: 1262 Indoor And Outdoor Antennas On Same AP?

Jun 19, 2012

I have a metal shop that needs wireless indoors and outdoors.
  
Will it work if I mount the 1262 inside with 4 indoor antennas mounted inside the building and 2 outdoor antennas mounted outside?

View 5 Replies


ADVERTISEMENT

Difference Between Indoor And Outdoor Wifi?

Mar 17, 2011

What is the difference between Indoor and Outdoor WiFi?

View 1 Replies View Related

Cisco Wireless :: AP1552 Directional Antennas Outdoor

Jun 30, 2012

I am expanding coverage in a big outdoor area.Most of the area is covered with AP1552 with AIR-ANT2506 5,2 db antennas.At the border of the area i have some masts where i can place ap's.Would it make sense to use directional antenna's there? I have a big open area where it is not possible to place ap's.The only placement is a mast in the middle of the area.I have a AP1552 with 5,2 db antennas there.Can i get better coverage if i place 3 or 4 ap's with directional antennas ?Or should i try with a 12dBi AIR-ANT24120 ?

View 2 Replies View Related

Cisco Wireless :: Can C1200 Antennas Work On 1262

Mar 21, 2012

1. Can the C1200 antennas work on the 1262 ?
2. Can the 2.4Ghz antenna work on the 5Ghz ports on the 1262 ?
3. The 1262 has 6 antenna ports (3 2.4ghz and 3 5ghz), can the (3) 2.4 Ghz antenna be used only as i only have antennas for the C1200 Access point which are 2.4 Ghz.

View 1 Replies View Related

Cisco Wireless :: Use AP1262 Indoor In Mesh Network With 1552E?

Mar 5, 2013

I have a running Mesh Network with AP 1552E and Controller 5508. The end customer has a new requirement to have a indoor coverage near to AP1552E (mesh AP). But in this building he has not any wired Network (it is far from any switched site). The question is: We can use an AP1262 indoor with Line Of Sigth to AP1552E in the running Mesh Network? I know AP1262 can be used in a  Mesh Netwok  (Root or Mesh) configuring it as BRIDGE [URL]

View 1 Replies View Related

Cisco Wireless :: To Deploy Indoor Mesh Deployment In Area 1500 Series

Aug 10, 2011

We are looking to deploy an indoor mesh deployment in an area where radar might be an issue.know that when using 1500 series APs you cannot choose UNII-1 channels even if they are deployed indoors.My question is if you can use a UNII-1 backhaul with indoor APs (3600 series for example) in an indoor mesh deployment.

View 8 Replies View Related

Cisco Wireless :: Is Aironet 1260 Good For Indoor LWAP Or CAPWAP Environment

Jul 12, 2012

Is Aironet 1260 good for indoor LWAP or CAPWAP environment? Do we need external antenna for the Aironet 1260 access point when using it indoor?

View 1 Replies View Related

Linksys Wrt54g / Indoor Wifi Range And/or Interference

May 21, 2011

I have Wireless-G 2.4ghz 54Mbps (Linksys WRT54G) working perfectly short range. But have no connection when I'm in room about 80 ft from router and have doors to rooms closed. Partitions in home are concrete block, not sheetrock. Should I get a new N router? Is there a repeater or booster that will do the job? Or connect existing router to new router in other room with ethernet cable going outside then over roof of house then inside to room?

View 14 Replies View Related

Cisco Wireless :: Use Patch Antennas With AP 1552E?

Sep 18, 2012

I need to use 14Dbi patch antennas (like AIR-ANT5114P-N I use to have on AP1522) on AP 1552E. Is it possible?

View 2 Replies View Related

Cisco Wireless :: AIR1242AG - Number Of Antennas

Apr 1, 2012

My customer wants to buy AIR1242AG with 2.4 GHZ antennas which are not ceiling mounted. How many 2.4 GHz antennas I can have on the  AIR1242AG?
 
Can I have a recommendation which antenna I should use which is not ceiling mounted?

View 1 Replies View Related

External Antennas For Wireless Adapter?

Sep 22, 2011

My desktop PC which has an Asus PCE-N13 Wireless Adapter with two stock SMA antennas receives a very poor signal due to the significant distance between my desktop and the router.In order to improve my signal strength, I thought about buying better 3rd party antennas and specifically external ones which I could place closer to the router that connect to the SMA connections on my wireless adapter via a wire. There's many of these antennas for sale I see, but I'm unsure which is best suited for my situation.

View 3 Replies View Related

Cisco Wireless :: 1522 Need To Add Two New Outdoor AP

Mar 9, 2012

Have a site that has a 1522 installed. I need to add two new outdoor AP's.  Would the 1550 work along with the 1522 or would I have to replace it?

View 2 Replies View Related

Cisco Wireless :: Possible To Use External Antennas On AP541N Set In WDS Mode

Aug 20, 2010

Is it possible to use external antennas on AP541N set in WDS mode? I would only need to use 802.11g mode 54mbps.I believe that the antennas shipped with the access points are removable RP-SMA.

View 3 Replies View Related

Cisco Wireless :: 3500 How Many 5.8 GHz Antennas To Pick For Each Radio

Dec 3, 2012

I am building a BOM for a customer and I need to present cheaper options than 3500 or 3600 APs. I thought of these two models but I don't know what models of antennas to pick.1602 is a 3X3 MIMO with 3 antenna connectors. How many 2.4 GHz and how many 5.8 GHz antennas should I pick for each radio?2602 is a 3X4 MIMO with 4 antenna connectors. In this case I suppose there are 2 connectors per radio.

View 9 Replies View Related

Cisco Wireless :: Antennas Doesn't Work On AP 3600

Mar 6, 2013

I´m trying to test anntenas in a AIR-CAP3062E-A-K9  the problem is that when I´m below the AP the speed is weak, the AP es with a WLC, so I was wondering if do you know a command or a form to test the anntenas or  the Radio.

View 7 Replies View Related

Cisco Wireless :: 1242AG - How To Find Out Model Of Antennas

Feb 25, 2013

I have an existing 1242AG AP in a remote location, I have full access to it.  I have a new 1242AG that was ordered but the client forgot to order antennas for it.  Is there a way I can find out the exact model of antennas that are connected to the in place AP at the remote location??

View 2 Replies View Related

Cisco Wireless :: WAP4410N Responding By Adding External Antennas?

Sep 21, 2010

I have not done the firmware for the units yet but have had only 1 outage thus far (but I think it was a power issue over the weekend).What I have done, 3 weeks ago, is put external antenna's on the 2 units which are 15 feet apart at 15dBi.The output is 40hz and I changed the latency time settings on the main unit, leaving the secondary at factory.This seems to be working for me so far. Usually goes down over the weekend and have to reset Mondays,but not this week.  I am afraid of running the firmware because then it may become unstable again.

View 6 Replies View Related

Cisco Wireless :: CAP-1602E - External Antennas In Separate Rooms

Feb 14, 2013

I have a question about external antennas on an access point. I have to plan a wireles solution, that also includes coverage in the industrial freezers. The freezers are one part of the sotck rooms, so the general coverage will be done with 1602I access points.
 
Since there are quite a lot of freezers in one location, installing separate AP in every freezer will be very expensive. I wondered if there is a possibility to put one 1602 access point with external antennas outside the freezer and then extend the antennas with 2m cables inside different freezers (1602E has three external antennas, so one antenna to each freezer).
 
Would this installation even work?
 
The freezers are quite small rooms maybe 2-3m2 sow the coverage is not a problem. But does this installation support multiple clients per AP in different freezers doing stocktaking with handheld terminals?

View 4 Replies View Related

Cisco Wireless :: AIR-LAP1242AG-E-K9 / 5GHz Antennas On 2.4GHz Radio?

Jul 16, 2012

We ordered 2 Cisco AIR-LAP1242AG-E-K9 Wireless Access Points with 4 AIR-ANT5135D-R antennas.We accidentally ordered the 5GHz antennas instead of the 2.4GHz antennas.Would it be possible to use the 5GHz antennas as 2.4GHz antennas?If so, are there any down sides to it?

View 15 Replies View Related

Cisco Wireless :: Installing Multiple Antennas (2450S) On AP1261?

Nov 11, 2012

I would like to install three antennas (2450S) on some AP1261 that i wold spread out 10 feet apart. I am not able to get the antenna on the C connector to transmit. I am not using 802.11N. This is for a warehouse where all the WiFi devices are 802.11G. My question is: can you get all three connectors on the AP to transmit.

View 8 Replies View Related

Cisco Wireless :: ANT25137NP-R Wi-Fi Coverage For Outdoor Area

Jul 30, 2012

I've been tasked with providing wireless coverage for an outdoor courtyard.  The wireless that bleeds out into the courtyard is minimal for both 2.4 and 5 Ghz bands.  I'm thinking a 3502p mounted just inside the wall hooked to a ANT25137NP-R patch antenna mount on an exterior wall. The red line on the wall will represent the antenna mounted on the wall.  This will be providing coverage for phones on 5Ghz and general devices on 2.4.

View 5 Replies View Related

Cisco Wireless :: 1552 Outdoor AP Disappears From WLC5508

Dec 30, 2012

My problem ist that i have 4 air-cap-1552e APs witch are powerde trugh Power Injectors. They worked fine for a few days but then the controller (7.2.111.3) lose connection to them. Right now i have only one Joined AP. The other 3 are status not joined. I can Ping all 4 Aps and wifi clients are connected through them.

View 8 Replies View Related

Cisco Wireless :: Does 1552x Outdoor AP Have Height Limitation

May 6, 2012

Customer wants to place a single 1552E to cover a particular area in his campus, and it will be placed on a tower, and the question is concerning the height. I can not find any particular height limitation such as 5 meters, 10 meters, etc. I understand this will influence the sign propagation as well as throughtput to the users, but can not find a matrix or a best practice guide for that.

View 1 Replies View Related

Cisco Wireless :: Mixing 1522 And 1552 Outdoor AP

Jun 13, 2013

Client has existing 1522 outdoor access points over different branches.1522 is dicontinued and 1552 is the replacement AP.Client intends to extend their outdoor wireless with the new AP's.Are there any known issues if the 1552 is mixed with 1522 envi?,Is a separate controller required for the new AP's?Will MESH work between 1522 and 1552 AP's?

View 3 Replies View Related

Cisco Wireless :: New Outdoor 1552E Cannot Join WLC 5508

May 13, 2012

I just have a brand new Aironet 1552E , just took it out of the box and connect to the same subnet with a WLC 5508 v7.2 fully config and working However, it could not join the WLC 5508.

View 4 Replies View Related

Cisco Wireless :: Power Rating Of 1552e Mesh AP Before Antennas Are Attached?

Mar 15, 2013

What is the power rating of a 1552e mesh AP before the antennas are attached? I have the dual band 2.4 / 5 GHz antennas. I know their Db rating, but I have not been able to find what the AP is.

View 1 Replies View Related

Cisco Wireless :: AIR-LAP1242G-A-K9 / Using 5.0ghz Antennas With 2.4ghz Access Point?

May 25, 2012

I'm working in a campus environment that has an existing wireless network using a Cisco AIR-WLC2112-K9 controller.There are 8 AIR-LAP1242G-A-K9 access points connected to the  controller. Each access point has a 5.0GHZ 4.5dbi Cisco omnidirectional  antenna, although the AP only supports 2.4GHZ.
 
Q1. Why a 5.0ghz antenna  might had been used with a 2.4ghz AP, and if we can expect increased  performance if we replace the antennas with 2.4ghz ones?
 
Q2.  On the controller, the antenna gain is set to 0 for each AP. Is there  also a benefit to leaving that 0 as opposed to 9 for 4.5dbi?

View 5 Replies View Related

Cisco Wireless :: Access Point 2602e Antennas Dual Band

Apr 9, 2013

I am currently looking for informations about access point 2602e, more precisly about antennas.This AP have four RTNC connectors for external antennas, but I found these table into Cisco documentation: [code] When I see that, I understand that we only need, to transmit, three antennas with 2,4 Ghz (which is the only band we will use in a first time), but four with 5 Ghz.I also found these informations, in the same documentation:The 2602E models are configured with up to four external dual-band dipole antennas, and two 2.4-GHz/5-GHz dual-band radios. The radios and antennas support frequency bands 2400–2500 MHz and 5150–5850 MHz through a common dual-band RF interface. Features of the external dual-band dipole antennas are:

• Four RTNC antenna connectors on the top of the access point
• Three TX and four RX antennas
 
My question: with four antennas, we have three TX and four RX, is it for 2,4 Ghz, 5 Ghz or both?

View 9 Replies View Related

Cisco Wireless :: AP541N / Antennas Were Set Aside Prior To Device Installation And Now Can't Be Found

Aug 30, 2012

Antennas were set aside prior to device installation, and now can't be found. Can they be ordered as a replacement kit?

View 3 Replies View Related

Cisco Wireless :: 1262 AP Convert To LAP?

Mar 13, 2012

Is it possible to convert autonomous access point Cisco 1262 to LAP?

View 9 Replies View Related

Cisco Wireless :: WLC5508 Required For Outdoor Mesh Configuration?

Jan 3, 2012

I want to start implementing a small outdoor mesh network of 3 APs Aironet 1550 in order to grow afterward with more APs. Is there any way to configure those 3 APs in an outdoor mesh configuration (for example, only one RAP and two MAPs) without a Wireless LAN Controller or I have to have at least, one WLC? My idea is to have a WLC 5508, but at the very beginning I don't know if my budget is gonna allow me to cost the WLC.

View 7 Replies View Related

Cisco Wireless :: 1552E - Outdoor Enterprise Mesh 802.11n Deployment

Jul 20, 2011

Is Cisco WCS mandatory when deploying an outdoor enterprise mesh solution?If I am goin to use the 1552E purely as an outdoor access point ,do I really need the Cisco WCS?

View 2 Replies View Related

Cisco Wireless :: 2600e Access Points With Outdoor Antenna?

Mar 14, 2013

I'm looking to extend wireless coverage outside the building and was think of using 2600e APs with AIR-ANT2566P4W-R patch antenna mounted externally.Is this a valid combination?
 
I've had a look through various bits of documentation and this antenna seems to be supported but can't see documentation that details of what low loss cables and lightening arrestors are compatible.

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved