I´m trying to test anntenas in a AIR-CAP3062E-A-K9 the problem is that when I´m below the AP the speed is weak, the AP es with a WLC, so I was wondering if do you know a command or a form to test the anntenas or the Radio.
View 7 Replies1. Can the C1200 antennas work on the 1262 ?
2. Can the 2.4Ghz antenna work on the 5Ghz ports on the 1262 ?
3. The 1262 has 6 antenna ports (3 2.4ghz and 3 5ghz), can the (3) 2.4 Ghz antenna be used only as i only have antennas for the C1200 Access point which are 2.4 Ghz.
We have an existing Cisco 2621 XM router with an ADSL interface connected to BT Broadband. Basic layout below:
Internet------ADSL on Cisco 2621 ------ Pix 506e ---- 3600 switch with inter VLAN routing to multiple VLANS
There are 5 static IP addresses. The internal FE port on the 2621 has one external assigned to it. The outside int of the PIX has another external IP assigned from the 5. The other 3 are NATd through to internal IPs via the PIX to internal servers etc.
The ADSL is being upgraded to BT Infinity. This new service comes with a separate VDSL modem and a separate BT router. Ideally I want to ignore the BT router and use the Cisco 2621 as it has 2 FE ports and I suspect I could do something using PPPOE.
So New layout would look like
Internet ----- BT VDSL modem------ Cisco 2621 ----- Pix 506e ---- 3600 switch with interVLAN routing to multiple VLANS
I think it is a bit strange the way it is setup as 2 static IPs cant be used. There is an opportunity to use a ASA 5505 which may become available.
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedI bought cisco AP (air-ap1142-e-k9) and we know this ap works with 802.11a/g/n same the description note on the package cartoon but my problem is when i configure that ap its work only with 802.11a/g i tries to make it works with 802.11n but fail .
View 3 Replies View RelatedWhenever my main PC is turned on, i get no signal from the wireless, like i cannot use my phone or laptop on the internet i use an Ethernet cable which is directly connected to my main PC my windows is also window XP and my modem model is TG782T only if my PC is turned off the wireless works
View 2 Replies View RelatedI purchased a used Compaq laptop with a Realtek USB wireless adapter. The laptop came with XP Pro. I connected the adapter and everything worked great. My husband got a virus I couldn't remove. I have the CD for XP Home so I did a clean install.Windows works fine. I connected the USB wireless adapter and ran the installation disk. When I open Realtek to connect nothing appears in the available networks. I checked the device mgr and it says Realtek is working. I turned off my 2Wire gateway and then reconnected it. I doubled checked that the Windows wireless utility is disabled. Still no available networks. Everything was fine before the reinstall of Windows XP Home.
View 5 Replies View RelatedWhenever my main PC is turned on, i get no signal from the wireless, like i cannot use my phone or laptop on the interneti use an [COLOR=blue !important][COLOR=blue !important]ethernet[/COLOR][/COLOR] cable which is direclty connected to my main PCmy windows is also window XP and my modem model is TG782T
View 2 Replies View Relatedreset my Linksys E1000 and now I can't access wifi from my phone as neither my pw or my default ps work.
View 2 Replies View Relatedlike today randomly my internet went down. And then everything changed back to its original like my SSID from Netcom it changed back to wireless and everything was default and also the PPP was off so i wasn't able to connect to the internet. So i went to my router setup page on the internet or whatever and turned it back on. So now like the internet on my computer which has a cable to the router works but the wireless internet doesn't work for my laptop nor ipod. I can see the connection on the laptop and ipod but when i try to connect it keeps saying that it is unable to connect.
View 7 Replies View RelatedI installed a Micro Edition of Windows 7. Everything is going properly with it except the wireless internet connection (its driver is installed and working properly as shown in Device Manager), by click Connect and typing the PW, it tries for few minutes then fail in connecting putting a yellow small circle on the wireless icon in Task bar
View 1 Replies View RelatedI upgraded my computer with a new graphics card and power supply. When I turned it on everything ran fine except for the internet. I either get a connection with 1 bar, a connection but no internet acess, or no internet at all. Did I damage something on the motherboard that could cause this?
View 11 Replies View RelatedMy wireless is connected fine but the internet wont work.I have internet explorer and firefox and it doesnt work on either.
View 1 Replies View RelatedMy fn f8 button doesnt work and doesnt seen when i click. and my wireless doesn't work. I tried to download new driver but it didnt work too.
View 1 Replies View RelatedI have this Belkin wireless g router, which I had for a year. I was using the wired connection since then until I, at last, was able to use it's wireless connection but it only lasted around a week. After that, the modem light on the router kept on blinking and the internet light wouldn't turn on. I also couldn't connect to the router anymore(wired and wireless), neither could I configure it. I reset it but it still didn't work.
View 1 Replies View RelatedI finished building my computer today, installed a fresh os and all the necessary drivers that came with the dvds provided, yet the wireless card doesn't even appear anywhere in the computer. The ethernet cabled one does, but not the wireless. Trying to connect to anything wireless just gives an endless searching process, with no results. I can't test the ethernet either, my router is all the way into the living room, way far out of reach.
Specs:
MB: Asus M4A88TD-V EVO/USB3
GPU: Asus 6870 HD
CPU: AMD Phenom II x4 955
I don't think anything else is necessary, is it?
The DIR-825 wireless simply doesn't work. When I called tech support, we cleared some settings and hard-powered the unit on/off and it finally turned on the wireless radio. A couple weeks later I pull out my laptop to use in the house via wireless and the wireless on the DIR-825 is OFFLINE AGAIN...fallen and it can't get UP.Is anyone having issues with keeping their wireless online? OK - powered it off for 5 minutes...now the wireless is working. I think changing configuration settings causes the thing to lock up.
View 1 Replies View RelatedTrying to troubleshoot a Cisco Pix 501. We have a cable modem/router that goes to the Cisco box that then goes to my wife's computer. It's worked flawlessly since we hooked it up, even if we unplug/replug the router. Today, we unplugged the Cisco box itself to hook up a newer one. When the newer one didn't work, we tried to hook up the old one again to no avail. The led indicators seem to show that everything's working properly. We've unplugged and rebooted everything. Nothing works. The network monitor on the computer shows that it detects being connected to a network, but it always says no internet access.
View 1 Replies View RelatedWe are deploying a new office and exploring the options for WLAN deployment. We were pretty impressed with 3500 series APs and that it supports CleanAir.However, we have decided to go for standalone AP deployment model now. As 3500 does not work in standalone mode, so we are looking for APs that can work in standalone mode ( and later can be converted to lightweight if needed). We can go for 1140 in that case. However, it would be better for us to know the main differences between features supported by 3500 lightweight AP and 1140 standalone AP. CleanAir looks like the main one. Are there other important ones as well?
View 2 Replies View Relatedi've upgraded our WLC 5508 from 7.0.220 to 7.2.115.1.For our guest WLAN we use web authentication with customized startpage, no login error page and no logout page. The customized login page is displayed correctly. After successful authentication the browser is forwarded to the default CISCO login page "login.html". No further autentication is possible, also no internet access.Reload the customized webauth bundle to the controller didn't change anything. Is there a change in the HTML/Java code of this controller version? I didn't find any hint in the release notes. Or do I need the newer web authentication bundle with version 1.0.2?
View 6 Replies View RelatedIt looks like pretty basic config, but it does not work. I have 1x 2602i autonomous mode AP, 1x C2960 switch (with inter-vlan routing prefered SDM template) and 1x 1841 router.
I trunk between Switch and Router works smoothly, but it does not work between AP and Switch or AP and Router.
Configuration looks like this:
AP2602i:
interface GigabitEthernet0
no ip address
duplex full
speed 100
[code]....
I just upload firmware1.0.1.10 on 2 WAP121. After the update and reboot, I was able to confirm the firmware version in the System Summary menu. The update is uneventful.However, the functions WDS Bridge and WorkGroup Bridge no longer works on two WAP121:
- For WDS Bridge, when I configure a Remote MAC Address with WPA Encryption and then I click on the Save button, nothing happens there. But it works well when I choose without Encryption.
- For WorkGroup Bridge, when I click on the Save button (even without changing the configuration), I have a message "Certificate file uploaded successfully" and another error message in the background: "error occured for query you send path . device.sync ... "
1.0.0.3 firmware is not available on your site, it is imposible for me to go back.
I've just setup a WAP321:
- 2 vlans: 200 & 250
- ip address on vlan 200 (management)
- SSID on vlan 200
- SSID on vlan 250
The LAN port is connected to Cisco Catalyst (Trunk 200,250). In vlan 200, there is the customer lan In vlan 250, there is a box to access to internet.
SSID associated to vlan 200 works properly. But the captive portal associated to vlan 250 doens't work. When we connect to it, and the captive portal is off, we can access to internet (the box give an ip address). But when I setup the captive portal to vap2 (vlan250), we can't access to internet (but the DHCP works properly). We have access to nothing, the page in the browser is blank.
I suspect a mistake with DNS configuration. I have read that the captive portal needs to be associated to vap0, is it true?
In attached files, the wap321 config.
I can not setup a new user, or access wireless networks that show on my laptop had a virus and the shop said they removed it but the network has not worked since it a dell inspiron 1525
View 1 Replies View RelatedI just switched houses, and when I connected my computer, modem and router I found out that I have internet on my PC which is wired, but when I try to get connected with my Laptop using the wireless funtion, it doesn't work. The laptop finds the router and gets "connected" but when I try to open a web page, it says there's an issue with my internet connection, and also something about not finding the DNS...whatever that means...as you can see..
View 1 Replies View RelatedI'm having an issue connecting to my wireless router. I can connect fine with security disabled, but it doesn't connect if I enable WPA. It says there's a "timeout" issue when I try to connect with WPA enabled.No one else is having issues connecting with their laptops and smartphones, so it must be a problem with my computer. [code]
View 5 Replies View Relatedmy wireless internet does not work after I rebooted my laptop.I tried installing wireless internet but it failed.What do i do?
View 1 Replies View RelatedI've found my old (1, or 2 years old) Realtek RTL8187B USB 2.0 Wireless Adapter. I plugged in into my PC, but it doesn't find any networks, but it works 100% on my laptop. On PC windows said, that maybe something wrong with the driver, I reinstalled it a few times, but same happened again, again. Both has Windows 7 Professional 64-bit.
View 13 Replies View Relatedmy werelss doesn't work becuase radio switch turn of and i can't turn it on
View 2 Replies View RelatedWhenever some other laptop in my room is using internet with its wifi my wifi stops working. I checked my ping when no laptop was using wifi that its runnig quite smoothly. But as soon as my room mates laptop gets connected to the same network my ping gives me output that "Request timed out".
View 2 Replies View RelatedI've been into the setup page several times over the years but now it won't load. I recently reset it and want to setup security again.
View 6 Replies View Relatedi have a Dell n 4030...a few days ago i changed its windows...i use windows 7 64bit...all of drivers has installed but wireless network doesn't work while it's driver has installed and it show work properly.
View 1 Replies View RelatedI try connecting via ethernet cable and it doesn't seem to work until the administrator of the network (my brother) comes home and then turns his computer on and starts using it. However, if i switch to a wireless adapter it sometimes works (like right now) even when my brother is not using the internet. Also, i tried to connect via wifi on my macbook pro to the same server and it used to work flawlessly 100% of the time, now i can only connect once in a while for short periods of times.
View 1 Replies View Related