Cisco Wireless :: AP1552 Directional Antennas Outdoor
Jun 30, 2012
I am expanding coverage in a big outdoor area.Most of the area is covered with AP1552 with AIR-ANT2506 5,2 db antennas.At the border of the area i have some masts where i can place ap's.Would it make sense to use directional antenna's there? I have a big open area where it is not possible to place ap's.The only placement is a mast in the middle of the area.I have a AP1552 with 5,2 db antennas there.Can i get better coverage if i place 3 or 4 ap's with directional antennas ?Or should i try with a 12dBi AIR-ANT24120 ?
View 2 Replies
ADVERTISEMENT
Nov 10, 2011
I've got two RT-N16's one is a bridge and the other is the AP.I don't need an omnidirectional antenna on the AP because it is literally in the highest, farthest corner of the structure and a quarter-sphere signal would be perfect... I'm looking for some antennas to replace the omnis on it. [URL]
View 1 Replies
View Related
Jun 19, 2012
I have a metal shop that needs wireless indoors and outdoors.
Will it work if I mount the 1262 inside with 4 indoor antennas mounted inside the building and 2 outdoor antennas mounted outside?
View 5 Replies
View Related
Oct 22, 2012
We have just finished installation of 12 AP 1552 as access points , clients are 7925G phone , after installation and configuration all clients can register and access to AP's in wireless environment but in IP we can't access to phones from our servers.For your information all phones and AP's and Ct5508 Controller are same subnet .We need install and configuer all 1552 just as Access points in 2.4Ghz , we don't need any mesh configuration.As for test we tried to connect to network by Laptop PC , it connected to access points but no network .
View 5 Replies
View Related
May 14, 2013
I used the AP 1552 Link Calculator to determine the coverage area of my AP deployment, however I have some concerns.I would like to know what the maximum radio range refers to when using an omni-directional antenna. Is this distance the radius or diameter of the coverage area? [code]
View 1 Replies
View Related
Jan 15, 2013
directional antenna for the WAP200e.
I've been googling but can't seem to find a product. I have found omni-directional but no directional antennae
View 2 Replies
View Related
Sep 5, 2012
The 3502e has 6 antenna connections, 3 for each band, 5GHz band is marked in blue. The antenna pigtails are only marked with the matching color - 3 blues or 3 blacks. No A,B or C. Does it matter which pigtail goes to which of the 3 terminals so long as the band is correct?
View 1 Replies
View Related
Nov 19, 2012
I have AP3500e serises and I need to cover distance up to 300m in directional point. I was trying to find any materials about distance which are covered by different types of antennas but I can't . I think I will prefer to use external antena , but can I get a converter from RP-TNC to N type connector.
View 6 Replies
View Related
Sep 6, 2011
I have three routers and 2 ISPs but I'd like to focus for now on a configuration with only one ISP provider. Here is my environment:
Netgear Cable (CBVG834G) wireless routerON the cable router are connected multimedia type equipments (TV/ IP set top box/ IP amp ) located on the family room DHCP ON (because I can't get internet connectivity when I assigned Fix IP address I come to that later) IP Adress:192.168.1.2 DHCP range:192.168.1.10/ 19 Reserved IP : 1292.168.1.10 for the Dlink 4 DEV a connected D-LINK ( DIR-855) wireless router.mainly PCs, NAS (x2) located on the first floor. DHCP ON Lan IP Adress: 192.168.0.1 DHCP range:
192.168.0.100 / 120 WAN Ip address : 192.168.1.10 6 PCs are connected
Everything works fine from an internet connectivity standpoint:
DEVx can connect to internet fine
PCx can connect to internet
PCx can access DEVx
Now the issue DEVx can't access resources from PCx!
View 4 Replies
View Related
Sep 18, 2012
I need to use 14Dbi patch antennas (like AIR-ANT5114P-N I use to have on AP1522) on AP 1552E. Is it possible?
View 2 Replies
View Related
Apr 1, 2012
My customer wants to buy AIR1242AG with 2.4 GHZ antennas which are not ceiling mounted. How many 2.4 GHz antennas I can have on the AIR1242AG?
Can I have a recommendation which antenna I should use which is not ceiling mounted?
View 1 Replies
View Related
Sep 22, 2011
My desktop PC which has an Asus PCE-N13 Wireless Adapter with two stock SMA antennas receives a very poor signal due to the significant distance between my desktop and the router.In order to improve my signal strength, I thought about buying better 3rd party antennas and specifically external ones which I could place closer to the router that connect to the SMA connections on my wireless adapter via a wire. There's many of these antennas for sale I see, but I'm unsure which is best suited for my situation.
View 3 Replies
View Related
Mar 9, 2012
Have a site that has a 1522 installed. I need to add two new outdoor AP's. Would the 1550 work along with the 1522 or would I have to replace it?
View 2 Replies
View Related
Aug 20, 2010
Is it possible to use external antennas on AP541N set in WDS mode? I would only need to use 802.11g mode 54mbps.I believe that the antennas shipped with the access points are removable RP-SMA.
View 3 Replies
View Related
Dec 3, 2012
I am building a BOM for a customer and I need to present cheaper options than 3500 or 3600 APs. I thought of these two models but I don't know what models of antennas to pick.1602 is a 3X3 MIMO with 3 antenna connectors. How many 2.4 GHz and how many 5.8 GHz antennas should I pick for each radio?2602 is a 3X4 MIMO with 4 antenna connectors. In this case I suppose there are 2 connectors per radio.
View 9 Replies
View Related
Mar 6, 2013
I´m trying to test anntenas in a AIR-CAP3062E-A-K9 the problem is that when I´m below the AP the speed is weak, the AP es with a WLC, so I was wondering if do you know a command or a form to test the anntenas or the Radio.
View 7 Replies
View Related
Feb 25, 2013
I have an existing 1242AG AP in a remote location, I have full access to it. I have a new 1242AG that was ordered but the client forgot to order antennas for it. Is there a way I can find out the exact model of antennas that are connected to the in place AP at the remote location??
View 2 Replies
View Related
Mar 21, 2012
1. Can the C1200 antennas work on the 1262 ?
2. Can the 2.4Ghz antenna work on the 5Ghz ports on the 1262 ?
3. The 1262 has 6 antenna ports (3 2.4ghz and 3 5ghz), can the (3) 2.4 Ghz antenna be used only as i only have antennas for the C1200 Access point which are 2.4 Ghz.
View 1 Replies
View Related
Sep 21, 2010
I have not done the firmware for the units yet but have had only 1 outage thus far (but I think it was a power issue over the weekend).What I have done, 3 weeks ago, is put external antenna's on the 2 units which are 15 feet apart at 15dBi.The output is 40hz and I changed the latency time settings on the main unit, leaving the secondary at factory.This seems to be working for me so far. Usually goes down over the weekend and have to reset Mondays,but not this week. I am afraid of running the firmware because then it may become unstable again.
View 6 Replies
View Related
Feb 14, 2013
I have a question about external antennas on an access point. I have to plan a wireles solution, that also includes coverage in the industrial freezers. The freezers are one part of the sotck rooms, so the general coverage will be done with 1602I access points.
Since there are quite a lot of freezers in one location, installing separate AP in every freezer will be very expensive. I wondered if there is a possibility to put one 1602 access point with external antennas outside the freezer and then extend the antennas with 2m cables inside different freezers (1602E has three external antennas, so one antenna to each freezer).
Would this installation even work?
The freezers are quite small rooms maybe 2-3m2 sow the coverage is not a problem. But does this installation support multiple clients per AP in different freezers doing stocktaking with handheld terminals?
View 4 Replies
View Related
Jul 16, 2012
We ordered 2 Cisco AIR-LAP1242AG-E-K9 Wireless Access Points with 4 AIR-ANT5135D-R antennas.We accidentally ordered the 5GHz antennas instead of the 2.4GHz antennas.Would it be possible to use the 5GHz antennas as 2.4GHz antennas?If so, are there any down sides to it?
View 15 Replies
View Related
Nov 11, 2012
I would like to install three antennas (2450S) on some AP1261 that i wold spread out 10 feet apart. I am not able to get the antenna on the C connector to transmit. I am not using 802.11N. This is for a warehouse where all the WiFi devices are 802.11G. My question is: can you get all three connectors on the AP to transmit.
View 8 Replies
View Related
Jul 30, 2012
I've been tasked with providing wireless coverage for an outdoor courtyard. The wireless that bleeds out into the courtyard is minimal for both 2.4 and 5 Ghz bands. I'm thinking a 3502p mounted just inside the wall hooked to a ANT25137NP-R patch antenna mount on an exterior wall. The red line on the wall will represent the antenna mounted on the wall. This will be providing coverage for phones on 5Ghz and general devices on 2.4.
View 5 Replies
View Related
Dec 30, 2012
My problem ist that i have 4 air-cap-1552e APs witch are powerde trugh Power Injectors. They worked fine for a few days but then the controller (7.2.111.3) lose connection to them. Right now i have only one Joined AP. The other 3 are status not joined. I can Ping all 4 Aps and wifi clients are connected through them.
View 8 Replies
View Related
May 6, 2012
Customer wants to place a single 1552E to cover a particular area in his campus, and it will be placed on a tower, and the question is concerning the height. I can not find any particular height limitation such as 5 meters, 10 meters, etc. I understand this will influence the sign propagation as well as throughtput to the users, but can not find a matrix or a best practice guide for that.
View 1 Replies
View Related
Jun 13, 2013
Client has existing 1522 outdoor access points over different branches.1522 is dicontinued and 1552 is the replacement AP.Client intends to extend their outdoor wireless with the new AP's.Are there any known issues if the 1552 is mixed with 1522 envi?,Is a separate controller required for the new AP's?Will MESH work between 1522 and 1552 AP's?
View 3 Replies
View Related
May 13, 2012
I just have a brand new Aironet 1552E , just took it out of the box and connect to the same subnet with a WLC 5508 v7.2 fully config and working However, it could not join the WLC 5508.
View 4 Replies
View Related
Mar 15, 2013
What is the power rating of a 1552e mesh AP before the antennas are attached? I have the dual band 2.4 / 5 GHz antennas. I know their Db rating, but I have not been able to find what the AP is.
View 1 Replies
View Related
May 25, 2012
I'm working in a campus environment that has an existing wireless network using a Cisco AIR-WLC2112-K9 controller.There are 8 AIR-LAP1242G-A-K9 access points connected to the controller. Each access point has a 5.0GHZ 4.5dbi Cisco omnidirectional antenna, although the AP only supports 2.4GHZ.
Q1. Why a 5.0ghz antenna might had been used with a 2.4ghz AP, and if we can expect increased performance if we replace the antennas with 2.4ghz ones?
Q2. On the controller, the antenna gain is set to 0 for each AP. Is there also a benefit to leaving that 0 as opposed to 9 for 4.5dbi?
View 5 Replies
View Related
Apr 9, 2013
I am currently looking for informations about access point 2602e, more precisly about antennas.This AP have four RTNC connectors for external antennas, but I found these table into Cisco documentation: [code] When I see that, I understand that we only need, to transmit, three antennas with 2,4 Ghz (which is the only band we will use in a first time), but four with 5 Ghz.I also found these informations, in the same documentation:The 2602E models are configured with up to four external dual-band dipole antennas, and two 2.4-GHz/5-GHz dual-band radios. The radios and antennas support frequency bands 2400–2500 MHz and 5150–5850 MHz through a common dual-band RF interface. Features of the external dual-band dipole antennas are:
• Four RTNC antenna connectors on the top of the access point
• Three TX and four RX antennas
My question: with four antennas, we have three TX and four RX, is it for 2,4 Ghz, 5 Ghz or both?
View 9 Replies
View Related
Aug 30, 2012
Antennas were set aside prior to device installation, and now can't be found. Can they be ordered as a replacement kit?
View 3 Replies
View Related
Jan 3, 2012
I want to start implementing a small outdoor mesh network of 3 APs Aironet 1550 in order to grow afterward with more APs. Is there any way to configure those 3 APs in an outdoor mesh configuration (for example, only one RAP and two MAPs) without a Wireless LAN Controller or I have to have at least, one WLC? My idea is to have a WLC 5508, but at the very beginning I don't know if my budget is gonna allow me to cost the WLC.
View 7 Replies
View Related
Jul 20, 2011
Is Cisco WCS mandatory when deploying an outdoor enterprise mesh solution?If I am goin to use the 1552E purely as an outdoor access point ,do I really need the Cisco WCS?
View 2 Replies
View Related
