I just have a brand new Aironet 1552E , just took it out of the box and connect to the same subnet with a WLC 5508 v7.2 fully config and working However, it could not join the WLC 5508.
View 4 Replieswhich controller I should use with 11 1552E AP ? I know 5508 will work with the AP's, but would the 2504 also work? If 2504 will work, I will go for the 2504 since its a cheaper solution.
View 5 Replies View Relatedwhich controller I should use with 11 1552E AP ? I know 5508 will work with the AP's, but would the 2504 also work? If 2504 will work, I will go for the 2504 since its a cheaper solution.
View 2 Replies View RelatedIs Cisco WCS mandatory when deploying an outdoor enterprise mesh solution?If I am goin to use the 1552E purely as an outdoor access point ,do I really need the Cisco WCS?
View 2 Replies View Relatedrecently I installed WLC 5508 en the central office and installed a network mesh in a remote office; central and remote office is connected with serial link as WAN, and I have dhcp server in the remote office for give ip address to all users and devices in the remote office. Additional I have 5 LAP1552 (mesh) and 2 LAP1260 in the remote office, all clients that connect to LAP1260(this don't belong to the mesh) receive ip address from dhcp server, but neither client that try to connect to the mesh (LAP1552) receive ip address from dhcp server. I don't have if I doing some thing bad. The range IP that receive the all ap's belong to the network of devices and the range ip for the users belong to network of users.
View 12 Replies View Relatedi have a problem with 1552E to register with 5508 WLC, and always got "AAA authentication error” in the WLC log, while AAA is not enabled. so my question is , do i need to add the MAC address to the WLC MAC filter list even if i not enable the AAA server in the WLC.
View 9 Replies View RelatedI have a cisco 5508 WLC and 40 cisco 360021 APs.I configured the WLC and assign the management interface IP and also configured a DHCP pool on my Cisco 4507 core switch wit option 43.But the problem that the APs connot join the WLC.
View 31 Replies View RelatedA customer runs a 5508 WLC for quit a while. several dozens AP's are spread all over Europe an run just fine. All the AP's have a VPN based connection over an MPLS service provider, so we are using 10.x.x.x addresses only. We have upgraded to release 7.2.111.3 to support OEAP 600 and we have configured NAT in the Firewall as well a policy to support the home office AP. Everything works fine until the switch where the WLC was attached to crushed. From this moment on, all internal AP's ar no longer able to register at the WLC. A log at the console port on an AP shows that it tries to access the external (NAT) IP address. We had to remove the NAT flag to support the internal AP's.
View 3 Replies View RelatedI have a 3502i(AP_1) that will not join a 5508 WLC(WLC_1)(code 7.2.103). The 3502i(AP_1) will join 4402 WLC(WLC_2)(Code 7.0.230). I have another 3502i(AP_2) that will join the WLC_1 & WLC_2. I am using capwap discover through DNS and hard coding the primiary WLC to AP_1 & AP_2. When I debug capwap events and errors, I see the static capwap messages and replies. Both of the WLC are on the same subnet. I have defauted the AP_1 and it joins the CISCO-CAPWAP-CONTROLLER as expected. When I change the Primiary WLC to WLC_1 it goes back to the CISCO-CAPWAP-CONTROLLER. If i change the primiary WLC to WLC_2 it joins. If I change the primiary back to WLC_1 it joins WLC_2 even though it is not a secondary. I know the previous joined WLC are stored in NVRAM, so that might be why it is doing that. I can join other ap to WLC_1 just not this one.
[code]....
I have a facility, where all the access points almost 250 of them are connected to two WisM's (One in each core switch ) . They are running in 6.0.199 firmware . These two WisM's are managed by WCS , which is running 6.0.188.
As i need to add more access points and to make fully redundant , 5500 controller was ordered and it has with firmware 7.0 installed. Couple of queries related with it .
1. Can 5500 be added in the WLC group, so that existing Access Points can be configured to use primary controller as 5500 and secondary / tertiary controller as WISM ?
2. Will 5500 be able to be detected by WCS , as the version of 5500 is 7.0 and WCS version is 6.0.188 ?
3. As WCS was already deployed and live, is it possible to upgrade, if the client has support contract like SUSA ?
We have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought before, together with the
WLC.AP's IP: 172.22.90.27 IOS version 12.4
WLC's IP: 172.22.90.20 IOS version 6.0.188.0
logs from the AP:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:06.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.045: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.046: bsnInitRcbSlot: slot 1 has NO radio
[Code] .....
The time is set to the WLC with the NTP. Don't lookup at the time the logs were made - they were made not during the same day/time
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error, I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface
[Code].....
My APs 1142N don't join their WLC. APs and WLC management interface are in the same vlan (WLC can ping all the APs). It is strange because it doesn't seem like they are trying to contact the WLC. What's strange is that I have other AP 1142N which joined this WLC without any problem.
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
[Code].....
I have problems with an AP AIR-CAP1552C-E-K9 (MAC: 2c:36:f8:73:e8:a0 )this AP cannot join to WLC 5508 software version 7.2.110.0.The AP ever gets associated to WLC.
I saw timeout messages and this error message:
%CAPWAP-3-ECHO_ERR: capwap_ac_sm.c:5656 Did not receive heartbeat reply; AP: 2c:36:f8:73:e8:a0
I don´t see any connectivity issues between the AP and WLC thorugh HFC network.One time the AP join to WLC and I saw this messages in debug CAPWAP:
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Change State Event Response sent to 10.64.128.165:16012
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 CAPWAP State: Run
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Sending the remaining config to AP 10.64.128.165:16012
[code].....
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
i'am trying to configure an AP1121g on my controller wlc5508 7.2 but i'am facing a compatibility issue.
View 5 Replies View Related1552E Rap will "lock" up, and not allow MAPs to connect through it to join. the WLC. Rebooting the Rap will resolve the issue, but the problem comes back and some random point in the future. Prior to rebooting the Rap to fix the issue, the Rap shows as joined to the WLC, but I have noticed that the neighbor details look stale, meaning my MAPs don't show up as neighbors, but other MAPs in the area are in the neighbor list, listed by MAC address. At this time, I can not confirm whether or not the neighbor detials are changing (updating), but I can confirm that my MAPs never show up as neighbors.As soon as the RAP is rebooted, MAPs join the controller again.
View 3 Replies View RelatedWe purchased cisco AIR-CAP1552E-A-K9 and it has IOS c1520-k9w8-mx.124-23c.JA2. WLC with the lastest firmware 7.0.116.0 is not able to connect to the Cisco 1552E. 1552E log show that it can see the WLC but unable to connect. We have devices for both U.S and Australia domain. Why are the 1552E not able to connect to the WLC?
View 19 Replies View RelatedI am designing a wireless mesh network for a client using several 1552 access points that will be bridged together. Only the RAP has a wired connection to their existing network. The client has informed me they want to hang switches off of the MAPs to connect existing wired devices. I found this in the install manual, "To forward bridge traffic, add a switch between the power injector and controller" but I will not be using power injectors (just AC power). Will adding a switch off of the AP's impact their wireless bridging abilities?
View 15 Replies View RelatedI can't find information about two features in 1524PS and 1552E/EU:
1. Does it have WEP encryption ?
2. Does it have SNMPv3 protocol for monitoring and remote managing ?
I guess, that software is similar in both, so answer will be the same in 1524PS and 1552E/EU.
How to confirm this features in 1524PS ?
I need to use 14Dbi patch antennas (like AIR-ANT5114P-N I use to have on AP1522) on AP 1552E. Is it possible?
View 2 Replies View Related% CDP is not supported on this interface, or for this encapsulation*Apr 2 18:35:20: %CAPWAP-3-ERRORLOG: capwap ifs: read error or timeout
[code]....
Have a site that has a 1522 installed. I need to add two new outdoor AP's. Would the 1550 work along with the 1522 or would I have to replace it?
View 2 Replies View RelatedDone a wifi mesh using 1552E and 1552i mix of AP's ? With the 1552E as RAP and 1552I's as MAP's ? Is it a recommended model of deployment and will it work well ? the 1552i having radiation pattern more towards the ground when mounted on top , will the mesh backhaul to the 1552E be strong enough ?
Will this work if i put the 1552e at a lower level than the 1552i so that the mesh is formed properly ?
I've looked through the documentation for loading the autonomous image on a 1552E WAP that has the lightweight image on it. All the documentation I can find mentions using the "archive" command at the command line. It doesn't appear to like the archive command.
I've seen in the documentation that it also mentions the software is loadable through the controller, but I can't figure out how to do that.
I currently have the 1552E connected to my 5508 controllers running 7.3 software. how to load this autonomous image on to the 1552E? I'm planning on using it to do site surveys with the 1552E.
I connected to AP 1552E and my computer via PoE Gigabit Ethernet Port. Port is up and two of them are the same subnets.Even if my computer and ap arp table seen each other but i couldnot ping the each of them. [code]
View 4 Replies View RelatedCan I power the 1552e with the proper poe injector if I am not using the ethernet port for backhaul? I want to get power thru poe but use a fiber for backhaul.
View 4 Replies View RelatedIn our mesh network. there are 8 root AP and 15 mesh AP . we are using 1552E ,i have few questions on it:
1. If the ap's acting as mesh ap are connected with only 2.4 ghz external antenna, will they have problem joining the root access point to form mesh.
2. How should we set the channel assignments. Do we only set them in root ap's.
3. should the channels be set under 802.11a ?
4.should the channel be manually set or should it be left to be chosen dynamically.
Is it possible to lower the power draw on the Aironet 1552e AP (AIR-CAP1552E-N-K9) so it will run on a standard PoE device (IEEE 802.3af). The spec sheet for the AP says you need to either use the Cisco PoE injector (AIR-PWRINJ1500-2=).Is there possibly a firmware upgrade/downgrade or some sort of command I can use?The APs being used are running LWAPP and require a controller.
View 2 Replies View RelatedI have a number of 1552e APs connected to a 5508 WLC. We are using local MAC filtering to enable the 1552's to connect to the WLC.
I have a several more 5508's in different locations, and can be used for back-up in the event the primary WLC fails.I have the primary WLC, a secondary WLC and a tertiary WLC loaded into each the 1552's HA tab.
My question concerns the secondary and tertiary WLCs... do I have to load all the MAC addresses in each of those as well in order for the 1552's to connect? If yes, is there an easy way to copy the local mac filtering from the primary WLC and load it into the other WLCs ?
I have a running Mesh Network with AP 1552E and Controller 5508. The end customer has a new requirement to have a indoor coverage near to AP1552E (mesh AP). But in this building he has not any wired Network (it is far from any switched site). The question is: We can use an AP1262 indoor with Line Of Sigth to AP1552E in the running Mesh Network? I know AP1262 can be used in a Mesh Netwok (Root or Mesh) configuring it as BRIDGE [URL]
View 1 Replies View RelatedI've been tasked with providing wireless coverage for an outdoor courtyard. The wireless that bleeds out into the courtyard is minimal for both 2.4 and 5 Ghz bands. I'm thinking a 3502p mounted just inside the wall hooked to a ANT25137NP-R patch antenna mount on an exterior wall. The red line on the wall will represent the antenna mounted on the wall. This will be providing coverage for phones on 5Ghz and general devices on 2.4.
View 5 Replies View Related