Cisco Wireless :: Access Point AIR-CAP1552C-E-K9 / Unable To Join WLC 5508?
Nov 26, 2012
I have problems with an AP AIR-CAP1552C-E-K9 (MAC: 2c:36:f8:73:e8:a0 )this AP cannot join to WLC 5508 software version 7.2.110.0.The AP ever gets associated to WLC.
I saw timeout messages and this error message:
%CAPWAP-3-ECHO_ERR: capwap_ac_sm.c:5656 Did not receive heartbeat reply; AP: 2c:36:f8:73:e8:a0
I don´t see any connectivity issues between the AP and WLC thorugh HFC network.One time the AP join to WLC and I saw this messages in debug CAPWAP:
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Change State Event Response sent to 10.64.128.165:16012
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 CAPWAP State: Run
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Sending the remaining config to AP 10.64.128.165:16012
[code].....
View 2 Replies
ADVERTISEMENT
Jan 10, 2013
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error, I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface
[Code].....
View 11 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
May 1, 2012
I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment
2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.
View 1 Replies
View Related
Aug 29, 2009
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
View 3 Replies
View Related
Aug 7, 2012
wlc 5508 code 7.0.220.0
AIR-CAP3502E-N-K9
each time that for what ever reason my access point goes down(not that my access point resets by itself, if i have to move it), the setting in the vlan mapping resets to whatever my native vlan is, in this case 30.
View 3 Replies
View Related
Feb 19, 2012
What is the OID for the count of the APs connected (and Status UP) to a WLC 5508?
View 2 Replies
View Related
Apr 25, 2011
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
View 3 Replies
View Related
May 10, 2012
I moved 1242 access point to my new buliding which i have 5508 wlc and 3500 acess point are working. i connected 1242 ap in network it got registered and download new ios and downlaoded the configuration and working fine. But i open the WLC tha 1242 ap are not visible in ap list.
View 3 Replies
View Related
Apr 22, 2013
Subject: FlexConnect compatibility with Access Point? We have today one Cisco 5508 and those access point on remote sites
o CISCO AIR-LAP-1131AG-E-K9
o CISCO AIR-LAP-1231G-E-K9
o CISCO AIR-LAP-1142N-E-K9
We plan to use redundancy on the controller and implement Flexconnect on the remote site. What we need to know is if I can implement Flexconnect on all actual access point - I think it is possible on 1142N + 1131G but do not know on 1231AG - is it correct or I'm wrong ? We plan to install the latest SW version for 5508 controller.
View 1 Replies
View Related
Sep 17, 2012
In our current Setup we have one WLC 4404 with 100 Access point license, now we have bought 3 number of 5508 WLC each supporting 100 Access point. Our plan is to Migrate all the Access point assosiation from 4404 to 5508. [code]
View 4 Replies
View Related
Aug 30, 2012
I have 50 WAP connected to a WLC 5508. When I backup the config I don't see the custom settings I put in some WAP. Where are the WAP settings saved at ?
View 17 Replies
View Related
Mar 13, 2013
I have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller. I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue? Can this LAN controller version will support this access point? My Lan Controller Management IP Address is 10.10.10.5 find the below configuration of 1300 access point.
AP001d.4513.dd68#reloadProceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.flashfs[0]: 4 files, 2 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 2052608flashfs[0]: Bytes available: 5688832flashfs[0]: flashfs fsck took 14 seconds.Base ethernet MAC Address: 00:1d:45:13:dd:68Initializing ethernet port 0...Reset ethernet port 0...Reset done!ethernet link up, 100 mbps,
[code].....
View 6 Replies
View Related
Oct 31, 2012
I have the wireless controller 5508 and many AP1261 registered on site. It detects a lot of rogue access points around. I would like to find out geographic location of these rogue access points. Is it possible?
View 2 Replies
View Related
Feb 24, 2013
i have a wlc 5508 and 40 access point 1141n there are 1500 users connected with this controller 5508. but when i ping at my gateway ,there is a disturbance in the temp response. [code]
View 1 Replies
View Related
Mar 16, 2013
I have a cisco 5508 WLC and 40 cisco 360021 APs.I configured the WLC and assign the management interface IP and also configured a DHCP pool on my Cisco 4507 core switch wit option 43.But the problem that the APs connot join the WLC.
View 31 Replies
View Related
Nov 14, 2012
A customer runs a 5508 WLC for quit a while. several dozens AP's are spread all over Europe an run just fine. All the AP's have a VPN based connection over an MPLS service provider, so we are using 10.x.x.x addresses only. We have upgraded to release 7.2.111.3 to support OEAP 600 and we have configured NAT in the Firewall as well a policy to support the home office AP. Everything works fine until the switch where the WLC was attached to crushed. From this moment on, all internal AP's ar no longer able to register at the WLC. A log at the console port on an AP shows that it tries to access the external (NAT) IP address. We had to remove the NAT flag to support the internal AP's.
View 3 Replies
View Related
Sep 25, 2012
I have a 3502i(AP_1) that will not join a 5508 WLC(WLC_1)(code 7.2.103). The 3502i(AP_1) will join 4402 WLC(WLC_2)(Code 7.0.230). I have another 3502i(AP_2) that will join the WLC_1 & WLC_2. I am using capwap discover through DNS and hard coding the primiary WLC to AP_1 & AP_2. When I debug capwap events and errors, I see the static capwap messages and replies. Both of the WLC are on the same subnet. I have defauted the AP_1 and it joins the CISCO-CAPWAP-CONTROLLER as expected. When I change the Primiary WLC to WLC_1 it goes back to the CISCO-CAPWAP-CONTROLLER. If i change the primiary WLC to WLC_2 it joins. If I change the primiary back to WLC_1 it joins WLC_2 even though it is not a secondary. I know the previous joined WLC are stored in NVRAM, so that might be why it is doing that. I can join other ap to WLC_1 just not this one.
[code]....
View 4 Replies
View Related
May 13, 2012
I just have a brand new Aironet 1552E , just took it out of the box and connect to the same subnet with a WLC 5508 v7.2 fully config and working However, it could not join the WLC 5508.
View 4 Replies
View Related
Jun 20, 2012
I have a facility, where all the access points almost 250 of them are connected to two WisM's (One in each core switch ) . They are running in 6.0.199 firmware . These two WisM's are managed by WCS , which is running 6.0.188.
As i need to add more access points and to make fully redundant , 5500 controller was ordered and it has with firmware 7.0 installed. Couple of queries related with it .
1. Can 5500 be added in the WLC group, so that existing Access Points can be configured to use primary controller as 5500 and secondary / tertiary controller as WISM ?
2. Will 5500 be able to be detected by WCS , as the version of 5500 is 7.0 and WCS version is 6.0.188 ?
3. As WCS was already deployed and live, is it possible to upgrade, if the client has support contract like SUSA ?
View 4 Replies
View Related
Mar 11, 2012
We have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought before, together with the
WLC.AP's IP: 172.22.90.27 IOS version 12.4
WLC's IP: 172.22.90.20 IOS version 6.0.188.0
logs from the AP:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:06.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.045: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.046: bsnInitRcbSlot: slot 1 has NO radio
[Code] .....
The time is set to the WLC with the NTP. Don't lookup at the time the logs were made - they were made not during the same day/time
View 6 Replies
View Related
Dec 27, 2012
My APs 1142N don't join their WLC. APs and WLC management interface are in the same vlan (WLC can ping all the APs). It is strange because it doesn't seem like they are trying to contact the WLC. What's strange is that I have other AP 1142N which joined this WLC without any problem.
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
[Code].....
View 4 Replies
View Related
Apr 19, 2012
Due to bandwith requirements, we need to join a network with a RV016 to a network with an RV082 via a point to point air bridge. (VPN over adls was not cutting it) fortunatelly there is line of sight.
The info
LocationA LocationB
RV016 RV082
WAN1 ADSL modem WAN1 ADSL Modem
WAN2 DedicatedIP modem WAN2 Free
WAN3..7 free
[code]....
We need LAN-B endpoints to be able to reach servers on location A and viceversa.
We pre configured two point to point radios for the tower people to install. (we could change this configs)
Topology (crude sketch)[URL]
Our questions: best port to plug the radios into the RVs WAN ports? switch ports? What rules or static routes need to be created?
View 2 Replies
View Related
Dec 17, 2011
I am connecting to the internet in two desktops using the WAG120N modem+router.I have no problems with the internet. But when I try to use the wireless access point in my mobile phone / laptop,the device is not able to find the WiFi access point. I need to swith off the modem and start it again, then the devices are finding the access point. I guess this has to do with some amount of inactivity and the modem switces off the wireless access point. I there anyway by which I can turn off that setting ? I have tried the setting page but was not able to find anything.
View 6 Replies
View Related
Mar 1, 2012
I have a wrt54gs v7 and a wap54g v3.1. Both have latest firmware on them. I set the access point to act as a repeater and entered the mac address from the router (It said to use the lan mac address. is that right?). I have them set on same subnet with static ip addresses. They have same wireless ssid and password with one using channel 10 and the other using channel 2. I can receive an ip address from the router and connect to internet. I cannot get an ip address from the access point. I tried a static ip on the computer and it will connect, but I don't have internet. Am I missing something in the setup? Can this access point act as a repeater for this router?
View 3 Replies
View Related
Sep 19, 2012
I know there were a few post about users losing their access point config after a power loss to the ap. I wanted to share that I can confirm and reproduce this same issue with a number of access points that I have. I opened a tac case and will update this tread as the case progresses.
Wlc 5508
Ap 1242
7.0.220.0
View 3 Replies
View Related
Apr 16, 2013
I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies
View Related
Mar 6, 2013
Setup N600 DB as an access point using the most recent firmware,3.03.12? Once I do I'm not able to access the dashboard even through I enabled the remote management option.
View 2 Replies
View Related
Nov 7, 2012
I’m having a problem of joining new Aps( Ari-ap1242G-E-k9 ) to the following wireless LAN controller. WLC details as follows,
Model No - AIR-CT5508-K9
Software Version - 7.0.116.0
AP Model - ARI-AP1242G-E-K9
AP console logs attached in Error.jpg file
View 5 Replies
View Related
Mar 7, 2013
Below are the errors that i am getting while trying to register AP (2606e) with vWLC (7.3.112) .
That is the error on vwlc
[code]....
But in wlc statistis we are able to see the ap join mac, screen shot is attached
View 6 Replies
View Related
Mar 10, 2012
we have WLC 4400, we have 40 APs with model no. AIR-LAP1131AG-N-K9 but we recenlty got an AP with model no. AIR-LAP1131AG-E-K9 which is unable to join WLC.
View 3 Replies
View Related
Jul 26, 2011
ISP: CharterType: CableRouters: Belkin N150 & Linksys E1200Devices: Laptop, ipad, desktop w/wireless card, hardwired desktopI had random issues with the Belkin router. I was able to hard-wire connect via the router but very randomly my wifi signal would go out and I would be completely unable to connect to the router on any device. Now I am having the exact same issues with my new Linksys router.Sometimes the wifi works and others I get "Unable to connect to network" or "Unable to join network". I have not yet noticed a pattern.Here are the things I have tried:
* Replace router with new router
* Remove encryption
* Change encryption types
* Restart both cable modem & router
* Factory reset of router
* Changed Channels
* Reboot of router from http://192.168.1.1 interface than mine) are all called 2WIRE490 and 2WIRE593.
View 11 Replies
View Related
Jan 14, 2012
I am not able to access my wireless access point anymore. I tried to access the web configuration in my browser as I have in the past 192.168.1.245, but I have no luck there. I tried to reset it by holding the reset button for 10-30 seconds, and I have no luck with that. What I have noticed on the AP is that the ethernet light keeps going out. The only light that is lit on my AP is the power and sometimes the ethernet light. My AP is connected to my router which I am able to gain access to the internet from any devices connected to the router except the AP. I have a router (E2000), a WAP4400N, and switch. I want to keep my wireless access separate from my business network. I cannot get my WAP4400N to work anymore.
View 1 Replies
View Related
