Cisco Wireless :: AIR-LAP1131AG-E-K9 Unable To Join Controller

Mar 10, 2012

we have WLC 4400, we have 40 APs with model no. AIR-LAP1131AG-N-K9 but we recenlty got an AP with model no. AIR-LAP1131AG-E-K9 which is unable to join WLC.

View 3 Replies


Cisco Wireless :: LAP1131AG Won't Join WLC On SRE-ISM

Jul 10, 2012

I am trying to set up a Wireless network a WLC hosted on an SRE module in a 2911 router. I think i have most of my bases covered but there is still one problem.
My LAP1131AG AP's won't join the controller, on the AP im am seeing this:
Translating "CISCO-LWAPP-CONTROLLER.test.local"...domain server ( [OK]


But to my knowledge an LWAP AP schould be able to join a CAPWAP WLC

View 2 Replies View Related

Cisco Wireless :: AIR-LAP1131AG-A-K9 Cannot Join On Virtual WLC

Feb 6, 2013

i have an AIR-LAP1131AG-A-K9 fresh from the box an was trying to register it to vWLC.I have them both on the same VLAN and these logs are showing on my WLC: [code]
The funny thing i have noticed is that both the WLC and the AP cannot PING each other.

View 14 Replies View Related

Cisco Wireless :: AIR-CT5508-K9 - Unable To Join AP To Controller

Nov 7, 2012

I’m having a problem of joining new Aps( Ari-ap1242G-E-k9 ) to the following wireless LAN controller. WLC details as follows,
Model No - AIR-CT5508-K9
Software Version -
AP Model - ARI-AP1242G-E-K9
AP console logs attached in Error.jpg file

View 5 Replies View Related

Cisco :: Unable To Join Wireless AP 1042 With 2106 Controller?

Nov 29, 2012

I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is it try to join with controller on ip address always. following are the error logs i can see on console. 
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN


View 4 Replies View Related

Cisco Wireless :: 1262 Lwap AP Unable To Join 5508 Wireless Controller

Nov 6, 2012

output are here
*Mar  1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar  1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar  1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR  (00
*Mar  1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar  1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address, mask, hostname AP2c54.2d0d.c3c4

View 1 Replies View Related

Cisco Wireless :: 2500 WLAN Controller Series Compatible With LAP1131AG?

Apr 17, 2012

I have a customer whom has six LAP1131AG-K9 but no controller and they are interested in one of the new 2500 series, specifically a AIR-CT2504-5-K9 with a 5 AP add-on license to bring total AP capacity to 10.  I can't determine clearly if this controller will work for these older AP's prior to them making the jump to 802.11n via the 3500 or 3600 series, looking to the community to confirm.

View 3 Replies View Related

Cisco Wireless :: AP 1310 Not Able To Join Controller

May 20, 2013

i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table


View 3 Replies View Related

Cisco Wireless :: AP C3502-I-K9 Does Not Join Controller

Oct 18, 2012

Network environment: (well configured and working fine)
2 AIR-WLC2106-K9 - Software Version
2 AIR-WLC2112-K9 - Software Version
10 AIR-LAP1252AG-T-K9 - Software Version
10 AIR-LAP1131AG-A-K9 - Software Version
I am adding a Cisco AP c3502-I-K9 to network.
It does not join any of the controllers.
Led is cycling through green, red, and off - that means "discovery/join process in progress" - never ends.
As wireless network is doing fine, I had only added to dhcp server dhcpd-subnet.conf file the above configuration:
class "Cisco AP c3500" {
match if option vendor-class-identifier = "Cisco AP c3500";
option vendor-class-identifier "Cisco AP c3500";


View 13 Replies View Related

Cisco Wireless :: 3502i Cannot Join Controller?

Oct 15, 2012

When we were installing some new APs, were plugged in to ports that were not configured on the WLC management VLAN.
This is the illustration
WLC management VLAN is VLAN 80 Management VLAN of infrastructure (Switches routers) is VLAN 10
The APs were plugged in to VLAN 10 and they were not able to associate themselves with the controllers.
Through research, those APs were getting a wrong IP address,
I did the Mode button, pressed for 30 secs, but this did not fix the problem, i thought it was going to clean the flash and bring the AP back to factory default I do not believe this happened.
We also added the cisco-capwap-controller.localdomain  to our DNS servers, and then I rebotted the APs and still no luck.
What fixed the issue is we had to go to the DHCP server, release the IP addresses and we found those based on the macs of the APs. What is we do not have the mac addresses?
Now that I have the DNS entry created, if I plug in an AP on the wrong VLAN port will I be able to see it?

View 3 Replies View Related

Cisco Wireless :: LAP Will Not Join 2106 Controller

Jan 21, 2012

I am trying to get one AP to join the 2106 controller, it did join once then never again!!  Now all I get is:
*Jan 22 11:16:22.088: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down


View 31 Replies View Related

Cisco Wireless :: 1142 Aironet Won't Join Controller

Aug 6, 2012

When I check the AP join statistics I  see the following: Reason For Last Unsuccessful Attempt    RADIUS authorization is pending for the AP, I don't run a radius server and don't know how to get around this so that the device can join.

View 4 Replies View Related

Cisco Wireless :: 3602 AP Cannot Join 2504 Controller

Oct 16, 2012

This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.

View 3 Replies View Related

Cisco Wireless :: AP LAP1142N Can't Join Controller - 4402

Apr 11, 2012

1) AP was originally running a standalone image.  I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode).

I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
ap: set


View 27 Replies View Related

Cisco Wireless :: Aironet 1230 Cannot Join Controller

May 7, 2012

my access point 1230 fail to join the controller. The image is C1200-k9w7-mx.123-8.JA2. I tried to reboot it but it does not join to controller. How do I initiate the discovery process again to make this AP to join? Should I convert it back to autonomous AP and then LWAPP process again? I can ping the AP from the controller and the AP is in the same VLAN with controller.

View 3 Replies View Related

Cisco Wireless :: Can't Join 1121-AG To Controller 4404 WLC

Jan 4, 2012

Iam having trouble to conect my 1121-AG AP`s to my 4404 WLC.
My WLC version is
I can see he AP is getting an IP address from the controller(internal DHCP). But from some reason they can`t connect to the WLC. I have tried many things such as:

1)reset to default settings

2) move the AP to Autonumos mode and back to LWAPP mode --  didnt work.

1 of my AP 1121AG is working properly.

View 11 Replies View Related

Cisco Wireless :: OfficeExtend AP Not Join Controller WLC5508

Oct 4, 2010

I try to configure an AP1131 as OfficeExtend but unfortunately I receive the following message from the debug command on the WLC5508: (Cisco Controller)

*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Discovery Request from XX.XX.XX.XX:14847
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Join Priority Processing status =


View 5 Replies View Related

Cisco Wireless :: WLC5504 AP Will Join To Controller But It Won't Work

Feb 27, 2013

we are running 5500-series WLC and AIR-LAP1131 and AIR-CAP3502 APs. Now we are trying to have new 1600-series AP's working with 5500WLCs. How to get this combo working.
WLC is running 7.4.100 sw version, and AP will join to controller but it won´t work.[code] I can´t find any kinf off document about invalid event 10 & state 5 combination erros message.

View 25 Replies View Related

Cisco Wireless :: 1142 AP Will Not Join Controller Through D-Link POE Switch

Apr 1, 2012

I'm trying to use 1142 APs with a 2504 Wireless Controller through a D-Link 48PT GBIT XSTACK SWITCH (DLI-DGS-3120-48PC/SI).At any rate, the 1142 AP joins with the wireless controller ONLY when I attach it directly to the controller.  When connected directly to the controller the AP functions normally and all is well. When I attach it through the D-Link switch, the AP flashs green several times, indicating that it can't find the controller.  I suspect that there's some setting on the D-Link switch that's preventing the AP from seeing the controller.

View 6 Replies View Related

Cisco Wireless :: Error To Join Secondary Controller WLC 7510

Jun 7, 2012

We have two controllers 7510 with the same config (SSID, Mobility Groups, etc)... All APs now was joined in wlc01... If we try to one o more APs join to another controller.. it's is not possible and debug show this . [code]

View 1 Replies View Related

Cisco Wireless :: LAP1240 - H-REAP Enabled AP Doesn't Join HQ Controller

Oct 14, 2012

i have configured cisco LAP1240 in H-Reap Mode for multiple branch offices with Local switching and central authentication. one of the branch's AP does not join the controller in HQ while the others are all ok. i have firewall only in HQ, i did priming first for all APs like let them join the controller and configure controller IP in high availbility, and H-Reap config and assign SSID to map with the branch local vlan. when i faced this issue first time i brought back ap and configure a static IP address for AP than recheck them again but the problem still same. since i have only one firewall in the network and also other branches joined the controller through that firewall and no issues.

View 3 Replies View Related

Cisco :: Lap 1121N Can't Join 5508 Controller

Sep 12, 2012

i'am trying to configure an AP1121g on my controller wlc5508 7.2 but i'am facing a compatibility issue.

View 5 Replies View Related

Cisco Wireless :: 1310 LAP Unable To Join WLC 5508?

Jan 10, 2013

I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error, I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar  1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar  1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface


View 11 Replies View Related

Cisco Wireless :: VWLC IOS 7.3.112 And 2602e AP Unable To Join Mac

Mar 7, 2013

Below are the errors that i am getting while trying to register AP (2606e) with vWLC (7.3.112) .
That is the error on vwlc
But in wlc statistis we are able to see the ap join mac, screen shot is attached

View 6 Replies View Related

Cisco AAA/Identity/Nac :: Force ACS V.5 To Join Domain With Certain Controller?

Sep 5, 2012

I try to join an ACS v. 5.3 to the domain.  For my acs in Location A, I can join without problems using my account. When I try to join the ACS in location B to the same domain with the same account, it doesnt work.I looked at the debug log files for the ad client, and noticed, that the ACS in location B goes to a certain Domain Controller. However, I would have expected the ACS to contact another DC, which is located on  the same location as the ACS ... this doesnt happen.
My question:  How does the ACS determine what DC to contact ? Is it possible to force the AC to join by connecting a certain DC ?

View 2 Replies View Related

Unable To Join Network On Wireless Router?

Jul 26, 2011

ISP: CharterType: CableRouters: Belkin N150 & Linksys E1200Devices: Laptop, ipad, desktop w/wireless card, hardwired desktopI had random issues with the Belkin router. I was able to hard-wire connect via the router but very randomly my wifi signal would go out and I would be completely unable to connect to the router on any device. Now I am having the exact same issues with my new Linksys router.Sometimes the wifi works and others I get "Unable to connect to network" or "Unable to join network". I have not yet noticed a pattern.Here are the things I have tried:

* Replace router with new router
* Remove encryption
* Change encryption types
* Restart both cable modem & router
* Factory reset of router
* Changed Channels
* Reboot of router from interface than mine) are all called 2WIRE490 and 2WIRE593.

View 11 Replies View Related

Cisco Wireless :: Access Point AIR-CAP1552C-E-K9 / Unable To Join WLC 5508?

Nov 26, 2012

I have problems with an AP AIR-CAP1552C-E-K9 (MAC: 2c:36:f8:73:e8:a0 )this AP cannot join  to WLC 5508 software version AP ever gets associated to WLC.

I saw timeout messages and this error message:
%CAPWAP-3-ECHO_ERR: capwap_ac_sm.c:5656 Did not receive heartbeat reply; AP: 2c:36:f8:73:e8:a0
I don´t see any connectivity issues between the AP and WLC thorugh HFC network.One time the AP join to WLC and I saw this messages in debug CAPWAP: 
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Change State Event Response sent to
  *spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 CAPWAP State: Run
 *spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Sending the remaining config to AP


View 2 Replies View Related

Cisco Wireless :: AIR-AP1242AG-E-K9 Unable To Join WLC 2504 After Upgrade To LWAPP

Sep 10, 2012

I have a few AIR-AP1242-E-K9 AP that I have upgraded to LWAPP, after the upgrade the AP's don't join the controller. But some AIR-AP1232AG-E-K9 on the same site joins without any issues.The controller is: AIR-CT2504-K9, SW: [code]

View 8 Replies View Related

Linksys Wireless Router :: WRT54GH - Unable To Join The Network?

Aug 31, 2010

Ive been using this router for about 4 months now. suddenly it wont let me connect wirelessly through itouch nor through imac. it says Unable to join the network "linksys" eventhough "linksys" is indicated to be an available WIFI network and that signal is full. Problem is still the same even after i reset the router a couple of times pass 30seconds, set the security to No Password.if i connect the router with a cable it connects seamlessly and allows me to go online.

View 8 Replies View Related

D-Link DIR-615 :: Cannot Get Wireless Items To Connect / Says Unable To Join Network

Apr 14, 2012

I reset my Dlink 615 wireless router.  I held down the power and reset for 30 seconds and rebooting the system with the disc.  I did change the router name, but believe everything else stayed the same.  My desk top is working fine being "hardwired" but nothing wireless will connect.

I did see this time it installed Network Magic which I have since uninstalled and again rebooted the computer system and still cannot get the wireless to work.  It shows the network available, but my password for some reason does not take.

View 1 Replies View Related

Linksys Wireless Router :: Unable To Join Network With Iphone And WRT610

Aug 7, 2011

I had PCs, Macs and other devices (iphone, itouch) able to connect fine to the WRT610n.   I moved to an apartment and when I turned the network on all the devices could connect expect for the iphone and itouch.  I have tried turning the wireless security off and MAC filtering off . I get the same "Unable to join the network" message. 

View 7 Replies View Related

Cisco Wireless :: 5508 Students Unable To Join Wireless With Personal Laptops

May 1, 2012

I have a WLC 5508, AIR-LAP1142N APs and a SSID for students to connect to who bring their own device. I am still testing this and it has not been rolled out but I am running into some serious issues with joining the network. I am authenticating them through a RADIUS server (2008 R2). Problem: many of them cannot connect because they are lacking the certificate.
1. What is a good setup for authentication in a BYOD environment

2. If my setup is good what can I do to allow kids to use their computers on the wireless either without the certificate (which I know is unlikely) or what do I need to have them do to connect. I am hoping it does not involve hard wiring and getting the certificate from the server.

View 1 Replies View Related

Linksys Wireless Router :: EA4500 IPhone Connection Unable To Join Network

Sep 19, 2012

My EA4500 router seems to drop mine and my wife's iPhone wifi connection at what appears to be the edge of my router's range. When we come back in range, our iPhone's intermittently give the error "Unable to join network.". And we're stuck in that mode. When I check the Devices menu in the CCC interface, I notice the iPhone device is configured and still online. However the "x" box to delete the device is greyed out because it's online. So how do I get out of this state and have my iPhone connect

View 2 Replies View Related

Copyrights 2005-15, All rights reserved