Cisco Wireless :: LAP1240 - H-REAP Enabled AP Doesn't Join HQ Controller
Oct 14, 2012
i have configured cisco LAP1240 in H-Reap Mode for multiple branch offices with Local switching and central authentication. one of the branch's AP does not join the controller in HQ while the others are all ok. i have firewall only in HQ, i did priming first for all APs like let them join the controller and configure controller IP in high availbility, and H-Reap config and assign SSID to map with the branch local vlan. when i faced this issue first time i brought back ap and configure a static IP address for AP than recheck them again but the problem still same. since i have only one firewall in the network and also other branches joined the controller through that firewall and no issues.
View 3 Replies
ADVERTISEMENT
May 20, 2013
i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
[Code].....
View 3 Replies
View Related
Oct 18, 2012
Network environment: (well configured and working fine)
2 AIR-WLC2106-K9 - Software Version 7.0.235.0
2 AIR-WLC2112-K9 - Software Version 7.0.235.0
10 AIR-LAP1252AG-T-K9 - Software Version 7.0.235.0
10 AIR-LAP1131AG-A-K9 - Software Version 7.0.235.0
I am adding a Cisco AP c3502-I-K9 to network.
It does not join any of the controllers.
Led is cycling through green, red, and off - that means "discovery/join process in progress" - never ends.
As wireless network is doing fine, I had only added to dhcp server dhcpd-subnet.conf file the above configuration:
class "Cisco AP c3500" {
match if option vendor-class-identifier = "Cisco AP c3500";
option vendor-class-identifier "Cisco AP c3500";
[Code].....
View 13 Replies
View Related
Oct 15, 2012
When we were installing some new APs, were plugged in to ports that were not configured on the WLC management VLAN.
This is the illustration
WLC management VLAN is VLAN 80 Management VLAN of infrastructure (Switches routers) is VLAN 10
The APs were plugged in to VLAN 10 and they were not able to associate themselves with the controllers.
Through research, those APs were getting a wrong IP address,
I did the Mode button, pressed for 30 secs, but this did not fix the problem, i thought it was going to clean the flash and bring the AP back to factory default I do not believe this happened.
We also added the cisco-capwap-controller.localdomain to our DNS servers, and then I rebotted the APs and still no luck.
What fixed the issue is we had to go to the DHCP server, release the IP addresses and we found those based on the macs of the APs. What is we do not have the mac addresses?
Now that I have the DNS entry created, if I plug in an AP on the wrong VLAN port will I be able to see it?
View 3 Replies
View Related
Jan 21, 2012
I am trying to get one AP to join the 2106 controller, it did join once then never again!! Now all I get is:
*Jan 22 11:16:22.088: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
[Code]....
View 31 Replies
View Related
Nov 7, 2012
I’m having a problem of joining new Aps( Ari-ap1242G-E-k9 ) to the following wireless LAN controller. WLC details as follows,
Model No - AIR-CT5508-K9
Software Version - 7.0.116.0
AP Model - ARI-AP1242G-E-K9
AP console logs attached in Error.jpg file
View 5 Replies
View Related
Aug 6, 2012
When I check the AP join statistics I see the following: Reason For Last Unsuccessful Attempt RADIUS authorization is pending for the AP, I don't run a radius server and don't know how to get around this so that the device can join.
View 4 Replies
View Related
Oct 16, 2012
This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies
View Related
Apr 11, 2012
1) AP was originally running a standalone image. I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode).
I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
ap: set
?=
DEFAULT_ROUTER=10.0.0.1
Default_router=10.9.99.1
ENABLE_BREAK=yes
[Code].....
View 27 Replies
View Related
May 7, 2012
my access point 1230 fail to join the controller. The image is C1200-k9w7-mx.123-8.JA2. I tried to reboot it but it does not join to controller. How do I initiate the discovery process again to make this AP to join? Should I convert it back to autonomous AP and then LWAPP process again? I can ping the AP from the controller and the AP is in the same VLAN with controller.
View 3 Replies
View Related
Jan 4, 2012
Iam having trouble to conect my 1121-AG AP`s to my 4404 WLC.
My WLC version is 7.0.116.0.
I can see he AP is getting an IP address from the controller(internal DHCP). But from some reason they can`t connect to the WLC. I have tried many things such as:
1)reset to default settings
2) move the AP to Autonumos mode and back to LWAPP mode -- didnt work.
1 of my AP 1121AG is working properly.
View 11 Replies
View Related
Oct 4, 2010
I try to configure an AP1131 as OfficeExtend but unfortunately I receive the following message from the debug command on the WLC5508: (Cisco Controller)
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Discovery Request from XX.XX.XX.XX:14847
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Join Priority Processing status =
[Code].....
View 5 Replies
View Related
Mar 10, 2012
we have WLC 4400, we have 40 APs with model no. AIR-LAP1131AG-N-K9 but we recenlty got an AP with model no. AIR-LAP1131AG-E-K9 which is unable to join WLC.
View 3 Replies
View Related
Feb 27, 2013
we are running 5500-series WLC and AIR-LAP1131 and AIR-CAP3502 APs. Now we are trying to have new 1600-series AP's working with 5500WLCs. How to get this combo working.
WLC is running 7.4.100 sw version, and AP will join to controller but it won´t work.[code] I can´t find any kinf off document about invalid event 10 & state 5 combination erros message.
View 25 Replies
View Related
Apr 1, 2012
I'm trying to use 1142 APs with a 2504 Wireless Controller through a D-Link 48PT GBIT XSTACK SWITCH (DLI-DGS-3120-48PC/SI).At any rate, the 1142 AP joins with the wireless controller ONLY when I attach it directly to the controller. When connected directly to the controller the AP functions normally and all is well. When I attach it through the D-Link switch, the AP flashs green several times, indicating that it can't find the controller. I suspect that there's some setting on the D-Link switch that's preventing the AP from seeing the controller.
View 6 Replies
View Related
Nov 29, 2012
I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console.
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
[code]....
View 4 Replies
View Related
Jun 7, 2012
We have two controllers 7510 with the same config (SSID, Mobility Groups, etc)... All APs now was joined in wlc01... If we try to one o more APs join to another controller.. it's is not possible and debug show this . [code]
View 1 Replies
View Related
Apr 25, 2011
today i upgraded our WLC4402 from 7.0.98.0 to 7.0.116.0. After the upgrade (also bootloader upgrade) the Aironet 1142 AP's do not joint the controller anymore. Error in log:*spamReceiveTask: Apr 26 11:30:46.301: %CAPWAP-3-DISC_INTF_ERR2: capwap_ac_sm.c:1468 Ignoring Primary discovery request received on a wrong VLAN (21) on interface (29) from AP ec:c8:82:ab:ed:00 Nothing changed in infrastructure. AP's are in VLAN 21, AP-Manager interface is in VLAN 21. Ap-Manager, Management Interface and Dynamic Interfaces are in PortChannel (LAG) = Interface 29.
View 8 Replies
View Related
Oct 1, 2012
Converted a Cisco 1231 with the Update Tool to lightweight (used c1200-rcvk9w8-tar.124-21a.JA2.tar). It worked, but now the AP issn't joining the wlc: [code]
View 8 Replies
View Related
Dec 27, 2012
My APs 1142N don't join their WLC. APs and WLC management interface are in the same vlan (WLC can ping all the APs). It is strange because it doesn't seem like they are trying to contact the WLC. What's strange is that I have other AP 1142N which joined this WLC without any problem.
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
[Code].....
View 4 Replies
View Related
Dec 5, 2011
Wireless doesnt get enabled on pressing fn+F2 key, it turns on for a fraction of a second signified by the sound but it again sounds and turns off.Just cant get it enabled...Is there any other way to turn it on, on my Inspiron 1545?
View 7 Replies
View Related
Jun 17, 2012
Flex 7500
Software Version: 7.2.103.0
I have a Flex 7500 with 200 1142AP's working fine in remote office and local setup. We have since purchased 3 OEAP 602's and looking to distribute to teleworkers.
I have configured the OEAP to point to the NAT'd IP of the WLC, the OEAP does connect and is listed briefly in the WLC wireless listing but I am not able to make any configuration changes, it will then dissassociate and try the join process all over again. I have attached below the OEAP 600 event log. I see that the WLC does not support data DTLS encryption and looking to make this work.
I have tried to install the DTLS license file from the Cisco website, but says license failed to install, with no other errors.
*Jun 18 15:18:43.938: Build version 7.0.112.72 (compiled Feb 3 2012 at 01:56:39, [L]).
*Jun 18 15:18:47.859: CAPWAP State: Init.
*Jun 18 15:18:47.860: CAPWAP State: Discovery.
[Code]....
View 2 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
Sep 12, 2012
i'am trying to configure an AP1121g on my controller wlc5508 7.2 but i'am facing a compatibility issue.
View 5 Replies
View Related
Sep 5, 2012
I try to join an ACS v. 5.3 to the domain. For my acs in Location A, I can join without problems using my account. When I try to join the ACS in location B to the same domain with the same account, it doesnt work.I looked at the debug log files for the ad client, and noticed, that the ACS in location B goes to a certain Domain Controller. However, I would have expected the ACS to contact another DC, which is located on the same location as the ACS ... this doesnt happen.
My question: How does the ACS determine what DC to contact ? Is it possible to force the AC to join by connecting a certain DC ?
View 2 Replies
View Related
Dec 29, 2011
I should upgrade ASA 5550 with nat controller enabled, from 7.2 to 8.x, I've been reading nat is differently configured up from release 8.3. So I choosed to upgrade to 8.2 release.
View 3 Replies
View Related
Mar 13, 2011
I've been trying to get it to work all day.When I open up Hamachi it shows the main screen with two buttons. Create a new network and Join an existing network.I've tried both but when I click create or join it doesn't do anything. Like it actually does nothing at all.Doesn't even close the window.Everything stays open and it doesn't either create or join any networks.
View 1 Replies
View Related
Dec 15, 2010
I am running a DIR-825 I believe one of the original's no updates or anything. I run it mixed mode. The 2.4 shows up and I can connect to but the 5 ghz (n) speed says it's enabled but I can never see it when I scan on any of my wireless n products (laptops and other computers). Dlink support told me to change to mixed mode g and n. I was running it in mixed mode (a, g and n). D link told me to change to mixed mode g and n and to make sure they stay on channel 6 and 11. Is this correct. Which firmware should I upgrade to and is there any easy way to do this?
View 4 Replies
View Related
Jun 4, 2013
I've enabled RDP on a laptop, but I can't connect to it. Pinging the laptop works. nmap shows ports open, but not RDP. netstat on the laptop shows nothing listening on 3389. I've also tried rebooting. [code]
View 1 Replies
View Related
Nov 20, 2012
I am trying to configure the Wism running on a 6500 switch.... I have configured the DHCP scope for the AP on the controller itself with the same subnet as of the management for the controller. The AP gets the IP but once it restarts it doesn't register to the controller, this is the log i get on the AP when consoled into it. [code]
View 6 Replies
View Related
May 5, 2013
i've upgraded our WLC 5508 from 7.0.220 to 7.2.115.1.For our guest WLAN we use web authentication with customized startpage, no login error page and no logout page. The customized login page is displayed correctly. After successful authentication the browser is forwarded to the default CISCO login page "login.html". No further autentication is possible, also no internet access.Reload the customized webauth bundle to the controller didn't change anything. Is there a change in the HTML/Java code of this controller version? I didn't find any hint in the release notes. Or do I need the newer web authentication bundle with version 1.0.2?
View 6 Replies
View Related
Mar 2, 2013
Is there is is any posibility to run WLC4402 and 104x family in H-REAP mode.
View 8 Replies
View Related
Oct 11, 2011
I'm reading up on H-REAP in the Deploying and troubleshooting Cisco Wireless LAN Controllers book (Chapter 13) and I would like some clarification on the except below.:"Also notice that, as part of the WLAN configuration, no mention was made of choosing and interface for the WLAN. Unless you will have APs in local mode servicing a WLAN configured for local switching in conjunction with H-REAP APs, the controller interface is irrelevant because the controller will not bridge the client traffic on the network.The H-REAP performs that function. Even if you will not be using any local mode APs, you must choose an interface to be associated with your WLAN. In this case, you could use the management interface or create a quarantine VLAN interface, for example if you do not want client traffic to be bridged by the controller if the client traffic is no longer locally switched."Our corporate office has 2 5508 controllers and 150+ APs in local mode. I'm preparing to deploy a couple of H-REAP APs to a remote site to test. Is this saying you have to choose an interface when creating a WLAN, but if the WLAN will only be used by H-REAP APs w/ local switching it does not matter which interface is used when creating the WLAN. If there are APs in local mode using the same WLAN, the interface the WLAN associates with needs to be on the same subnet as the devices connecting the the WLAN?
View 3 Replies
View Related
