Cisco :: Unable To Join Wireless AP 1042 With 2106 Controller?
Nov 29, 2012
I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console.
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
[code]....
View 4 Replies
ADVERTISEMENT
Jan 21, 2012
I am trying to get one AP to join the 2106 controller, it did join once then never again!! Now all I get is:
*Jan 22 11:16:22.088: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
[Code]....
View 31 Replies
View Related
Nov 7, 2012
I’m having a problem of joining new Aps( Ari-ap1242G-E-k9 ) to the following wireless LAN controller. WLC details as follows,
Model No - AIR-CT5508-K9
Software Version - 7.0.116.0
AP Model - ARI-AP1242G-E-K9
AP console logs attached in Error.jpg file
View 5 Replies
View Related
Mar 10, 2012
we have WLC 4400, we have 40 APs with model no. AIR-LAP1131AG-N-K9 but we recenlty got an AP with model no. AIR-LAP1131AG-E-K9 which is unable to join WLC.
View 3 Replies
View Related
Jul 7, 2011
I setup a mini wireless LAN network lab with a not for resale 2106 wireless lan controller and a sales air-lap1242ag access point. I do not have a DHCP and DNS in my lab environment. I have configured the WLC with the basic configuration using the CLI wizard, i also configured the WLC as a DHCP server for clients that will be connecting to the APs associated to the controller.
I powered up the AP and connect the ethernet port directly to the controller, the controller issued an IP address to the AP, the AP downloaded a new operating system from the controller but failed to join the controller.
I check both debug message on the controller console and the trap messages on the controller's GUI and it say the AP could not download a configuration from the controller and it is beacuse of invalid license. Below is the trap message:
Configuration Phase Statistics Requests ReceivedResponses SentUnsuccessful Request ProcessedReason For Last Unsuccessful AttemptLast Successful Attempt TimeLast Unsuccessful Attempt TimeLast Error SummaryLast AP Message Decryption FailureLast AP Connection FailureLast Error Occurred Last Error Occurred ReasonLast Join Error Timestamp
Also, I tried to log into the GUI of the AP using the both the username and password ''Cisco'' but I cannot get into the device. I can only get in through the CLI. In the CLI, almost all the commands I enter gives an error the it is disabled. I don't know what to do any more, I want to know if the access point is faulty or i am not doing the right thing.
View 4 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
Sep 20, 2012
Can 2 Aironet 1042's using WDS handoff a session between them without any other network hardware needed?
View 1 Replies
View Related
Jul 21, 2012
I ordered controller 2504 and will arrive soon. I want to know that after configure the initial setup of 2504 (i.e. AP manager , Management IPs etc) and defining the DHCP for AP. Will the 1042 lightweight AP will register with the controller automatically or i need to manually define the AP (MAC address) on WLC. and also whether the Option 43 and 60 are correctly defined?
Management Interface: 10.10.22.15
AP Manager Int: 10.10.22.16
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
[code]...
View 4 Replies
View Related
Jun 11, 2012
I have a 5508 WLC licensed for 100 APs. I have 1 - 1042 LAP connected for testing. I have DHCP configured for the AP, and it gets an address of 192.168.254.100/24 - the controller's management interface is 192.168.254.99/24. I can see that the AP is getting an IP and I can ping it from the controller. However, I simply do not see the AP associating. I enabled capwap debiugging and watched the events, but I didn't see anything crazy that clued me in. What am I doing wrong?
The controller is v6.0.199.4
Every time I have set these up in the past they have been pretty straight forward. I haven't gotten too deep into the config on the WLC becuase I don't want to cause more issues.
View 2 Replies
View Related
Mar 22, 2011
how I can find out what version of SSH that a cisco 2106 wireless LAN controller is using?Is there a CLI I can type to figure that out or do they only support one version?
View 1 Replies
View Related
Oct 13, 2011
after an unplanned power outage the WLAN in our office has stopped routing. Clients can associate and get an IP address from the DHCP server on the controller but cannot get past the controller. A PC on the LAN can ping the default gateway of the SSID (dynamic interface) but cannot ping the client. Attached is a diagram of the setup. I am trying to find out how to add a default/static route via the L3 switch that the controller is connected to but am unable to do so either through the CLI or GUI. The controller (AIR-WLC2106-K9) is operating on ver 5.2.157.0.
View 5 Replies
View Related
Jan 6, 2013
I have a question to migrate a customer from a 2106 controller to a 2504 controller. Can I use the configuration file with both controllers having the same version?
Or is there another way not having to do it again manually? The old configuration is OK, only the hardware is end of sale.
View 19 Replies
View Related
May 18, 2012
I would like to get webauth bundle sample to create custom page for our AP controllers but I'm unable to find the sample .tar within the WCS itself.Some other WCS manuals has references in them that says there should be link to download sample from WCS but clearly 2106 hasn't got one.There's one in download section "webauth bundle 1.0.2.zip" but this is for registered partners and costumers, we are not registered as partners and cannot download the sample ourselves.
View 2 Replies
View Related
May 20, 2013
i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
[Code].....
View 3 Replies
View Related
Oct 18, 2012
Network environment: (well configured and working fine)
2 AIR-WLC2106-K9 - Software Version 7.0.235.0
2 AIR-WLC2112-K9 - Software Version 7.0.235.0
10 AIR-LAP1252AG-T-K9 - Software Version 7.0.235.0
10 AIR-LAP1131AG-A-K9 - Software Version 7.0.235.0
I am adding a Cisco AP c3502-I-K9 to network.
It does not join any of the controllers.
Led is cycling through green, red, and off - that means "discovery/join process in progress" - never ends.
As wireless network is doing fine, I had only added to dhcp server dhcpd-subnet.conf file the above configuration:
class "Cisco AP c3500" {
match if option vendor-class-identifier = "Cisco AP c3500";
option vendor-class-identifier "Cisco AP c3500";
[Code].....
View 13 Replies
View Related
Oct 15, 2012
When we were installing some new APs, were plugged in to ports that were not configured on the WLC management VLAN.
This is the illustration
WLC management VLAN is VLAN 80 Management VLAN of infrastructure (Switches routers) is VLAN 10
The APs were plugged in to VLAN 10 and they were not able to associate themselves with the controllers.
Through research, those APs were getting a wrong IP address,
I did the Mode button, pressed for 30 secs, but this did not fix the problem, i thought it was going to clean the flash and bring the AP back to factory default I do not believe this happened.
We also added the cisco-capwap-controller.localdomain to our DNS servers, and then I rebotted the APs and still no luck.
What fixed the issue is we had to go to the DHCP server, release the IP addresses and we found those based on the macs of the APs. What is we do not have the mac addresses?
Now that I have the DNS entry created, if I plug in an AP on the wrong VLAN port will I be able to see it?
View 3 Replies
View Related
Aug 6, 2012
When I check the AP join statistics I see the following: Reason For Last Unsuccessful Attempt RADIUS authorization is pending for the AP, I don't run a radius server and don't know how to get around this so that the device can join.
View 4 Replies
View Related
Oct 16, 2012
This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies
View Related
Apr 11, 2012
1) AP was originally running a standalone image. I booted it into a so-called ROMMON or AP mode (ESC is the right key to make it boot into this mode).
I found a recovery image in its flash - c1140-rcvk9w8-mx. I made the AP boot from it by using "set" command and I see that it start booting using this recovery image. Here goes the question. Do all AP settings matter ? E.g. when I run "set" command from AP I see the following:
ap: set
?=
DEFAULT_ROUTER=10.0.0.1
Default_router=10.9.99.1
ENABLE_BREAK=yes
[Code].....
View 27 Replies
View Related
May 7, 2012
my access point 1230 fail to join the controller. The image is C1200-k9w7-mx.123-8.JA2. I tried to reboot it but it does not join to controller. How do I initiate the discovery process again to make this AP to join? Should I convert it back to autonomous AP and then LWAPP process again? I can ping the AP from the controller and the AP is in the same VLAN with controller.
View 3 Replies
View Related
Jan 4, 2012
Iam having trouble to conect my 1121-AG AP`s to my 4404 WLC.
My WLC version is 7.0.116.0.
I can see he AP is getting an IP address from the controller(internal DHCP). But from some reason they can`t connect to the WLC. I have tried many things such as:
1)reset to default settings
2) move the AP to Autonumos mode and back to LWAPP mode -- didnt work.
1 of my AP 1121AG is working properly.
View 11 Replies
View Related
Oct 4, 2010
I try to configure an AP1131 as OfficeExtend but unfortunately I receive the following message from the debug command on the WLC5508: (Cisco Controller)
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Discovery Request from XX.XX.XX.XX:14847
*spamApTask4: Oct 04 17:19:18.043: 00:1b:90:74:37:e0 Join Priority Processing status =
[Code].....
View 5 Replies
View Related
Feb 27, 2013
we are running 5500-series WLC and AIR-LAP1131 and AIR-CAP3502 APs. Now we are trying to have new 1600-series AP's working with 5500WLCs. How to get this combo working.
WLC is running 7.4.100 sw version, and AP will join to controller but it won´t work.[code] I can´t find any kinf off document about invalid event 10 & state 5 combination erros message.
View 25 Replies
View Related
May 31, 2011
I'm setting up a 2106 controller with 3 APs.
When I connect the APs to a port on our 3550 switch, the AP gets an IP and associates with the 2106 controller. I can ping the AP from a wired PC and associate a wireless client to it. When I connect them to the PoE ports that are on the controller, it gets an IP and associates with the controller but, I cannot ping it from a wired PC or wireless client but, I can associate a wireless client to it.
The AP manager and Management interfaces, under PHYSICAL OPERATION are configured for port 1, which is the port that connects the Controller to the rest of the network. Since the whole network is using VLAN 1, I set the VLANs for the Management interface and AP interface to 0, untagged. I noticed when I set the AP manager interface to 1 I get the same results.
View 5 Replies
View Related
Apr 1, 2012
I'm trying to use 1142 APs with a 2504 Wireless Controller through a D-Link 48PT GBIT XSTACK SWITCH (DLI-DGS-3120-48PC/SI).At any rate, the 1142 AP joins with the wireless controller ONLY when I attach it directly to the controller. When connected directly to the controller the AP functions normally and all is well. When I attach it through the D-Link switch, the AP flashs green several times, indicating that it can't find the controller. I suspect that there's some setting on the D-Link switch that's preventing the AP from seeing the controller.
View 6 Replies
View Related
Jun 7, 2012
We have two controllers 7510 with the same config (SSID, Mobility Groups, etc)... All APs now was joined in wlc01... If we try to one o more APs join to another controller.. it's is not possible and debug show this . [code]
View 1 Replies
View Related
Oct 14, 2012
i have configured cisco LAP1240 in H-Reap Mode for multiple branch offices with Local switching and central authentication. one of the branch's AP does not join the controller in HQ while the others are all ok. i have firewall only in HQ, i did priming first for all APs like let them join the controller and configure controller IP in high availbility, and H-Reap config and assign SSID to map with the branch local vlan. when i faced this issue first time i brought back ap and configure a static IP address for AP than recheck them again but the problem still same. since i have only one firewall in the network and also other branches joined the controller through that firewall and no issues.
View 3 Replies
View Related
Sep 12, 2012
i'am trying to configure an AP1121g on my controller wlc5508 7.2 but i'am facing a compatibility issue.
View 5 Replies
View Related
Jan 10, 2013
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error, I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface
[Code].....
View 11 Replies
View Related
Mar 7, 2013
Below are the errors that i am getting while trying to register AP (2606e) with vWLC (7.3.112) .
That is the error on vwlc
[code]....
But in wlc statistis we are able to see the ap join mac, screen shot is attached
View 6 Replies
View Related
Sep 5, 2012
I try to join an ACS v. 5.3 to the domain. For my acs in Location A, I can join without problems using my account. When I try to join the ACS in location B to the same domain with the same account, it doesnt work.I looked at the debug log files for the ad client, and noticed, that the ACS in location B goes to a certain Domain Controller. However, I would have expected the ACS to contact another DC, which is located on the same location as the ACS ... this doesnt happen.
My question: How does the ACS determine what DC to contact ? Is it possible to force the AC to join by connecting a certain DC ?
View 2 Replies
View Related
Jul 26, 2011
ISP: CharterType: CableRouters: Belkin N150 & Linksys E1200Devices: Laptop, ipad, desktop w/wireless card, hardwired desktopI had random issues with the Belkin router. I was able to hard-wire connect via the router but very randomly my wifi signal would go out and I would be completely unable to connect to the router on any device. Now I am having the exact same issues with my new Linksys router.Sometimes the wifi works and others I get "Unable to connect to network" or "Unable to join network". I have not yet noticed a pattern.Here are the things I have tried:
* Replace router with new router
* Remove encryption
* Change encryption types
* Restart both cable modem & router
* Factory reset of router
* Changed Channels
* Reboot of router from http://192.168.1.1 interface than mine) are all called 2WIRE490 and 2WIRE593.
View 11 Replies
View Related
Nov 26, 2012
I have problems with an AP AIR-CAP1552C-E-K9 (MAC: 2c:36:f8:73:e8:a0 )this AP cannot join to WLC 5508 software version 7.2.110.0.The AP ever gets associated to WLC.
I saw timeout messages and this error message:
%CAPWAP-3-ECHO_ERR: capwap_ac_sm.c:5656 Did not receive heartbeat reply; AP: 2c:36:f8:73:e8:a0
I don´t see any connectivity issues between the AP and WLC thorugh HFC network.One time the AP join to WLC and I saw this messages in debug CAPWAP:
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Change State Event Response sent to 10.64.128.165:16012
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 CAPWAP State: Run
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Sending the remaining config to AP 10.64.128.165:16012
[code].....
View 2 Replies
View Related
