Cisco Wireless :: WebAuth Bundle In 2106 AP Controller?
May 18, 2012
I would like to get webauth bundle sample to create custom page for our AP controllers but I'm unable to find the sample .tar within the WCS itself.Some other WCS manuals has references in them that says there should be link to download sample from WCS but clearly 2106 hasn't got one.There's one in download section "webauth bundle 1.0.2.zip" but this is for registered partners and costumers, we are not registered as partners and cannot download the sample ourselves.
View 2 Replies
ADVERTISEMENT
Nov 8, 2010
I have a new fresh 5508 release 7.0.98.0 When I try to download (I mean upload to the controller) a customized Webauth bundle in .tar format I have the following message error in the syslog :*TransferTask: Oct 29 12:56:08.894: %UPDATE-3-UNTAR_CMD_FAIL: updcode.c:2832 Error during untar of webauth bundle. Tar returned 256.
View 17 Replies
View Related
May 19, 2012
Recectly we replaced Cisco 2100 Series LAN controller to Cisco 5508 Wirless LAN controller , I downloaded WebAuth Bundle from my Old LAN Controller ,when i am trying to upload to my New Wireless LAN controller ,its not uploading and also it gave me uploading failure error message .
View 2 Replies
View Related
Jul 26, 2011
I have in the past downloaded the webauth bundle to a wlc 5508 running 7.0.98 successfully. I am trying to upload a new bundle after modifying the AUP but I get an error after the download to the wlc.
The error with FTP or TFTP is
% Error: Webauth Bundle file transfer failed - Unknown error - refer to log
I've tried to copy the unmodified bundle from the zip and get the same error so I don't think it's the login.tar file.
View 3 Replies
View Related
May 5, 2013
i've upgraded our WLC 5508 from 7.0.220 to 7.2.115.1.For our guest WLAN we use web authentication with customized startpage, no login error page and no logout page. The customized login page is displayed correctly. After successful authentication the browser is forwarded to the default CISCO login page "login.html". No further autentication is possible, also no internet access.Reload the customized webauth bundle to the controller didn't change anything. Is there a change in the HTML/Java code of this controller version? I didn't find any hint in the release notes. Or do I need the newer web authentication bundle with version 1.0.2?
View 6 Replies
View Related
May 21, 2013
We have disabled the WebAuth SecureWeb on our 5508 WLCs so Guest users can access the guest splash page without the certifiacate error. The controllers are currently running 7.3.112.0. Everything works fine with the WebAuth SecureWeb enabled, but once we disable the guest users are not redirecting to the splash page anymore. I remember having to reload the controller in the past to disable HTTPS completely, but is this still the case? I don't see any documentation supporting the need to reload.
View 2 Replies
View Related
Mar 22, 2011
how I can find out what version of SSH that a cisco 2106 wireless LAN controller is using?Is there a CLI I can type to figure that out or do they only support one version?
View 1 Replies
View Related
Jan 21, 2012
I am trying to get one AP to join the 2106 controller, it did join once then never again!! Now all I get is:
*Jan 22 11:16:22.088: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
[Code]....
View 31 Replies
View Related
Oct 13, 2011
after an unplanned power outage the WLAN in our office has stopped routing. Clients can associate and get an IP address from the DHCP server on the controller but cannot get past the controller. A PC on the LAN can ping the default gateway of the SSID (dynamic interface) but cannot ping the client. Attached is a diagram of the setup. I am trying to find out how to add a default/static route via the L3 switch that the controller is connected to but am unable to do so either through the CLI or GUI. The controller (AIR-WLC2106-K9) is operating on ver 5.2.157.0.
View 5 Replies
View Related
Jan 6, 2013
I have a question to migrate a customer from a 2106 controller to a 2504 controller. Can I use the configuration file with both controllers having the same version?
Or is there another way not having to do it again manually? The old configuration is OK, only the hardware is end of sale.
View 19 Replies
View Related
Nov 29, 2012
I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console.
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
[code]....
View 4 Replies
View Related
May 31, 2011
I'm setting up a 2106 controller with 3 APs.
When I connect the APs to a port on our 3550 switch, the AP gets an IP and associates with the 2106 controller. I can ping the AP from a wired PC and associate a wireless client to it. When I connect them to the PoE ports that are on the controller, it gets an IP and associates with the controller but, I cannot ping it from a wired PC or wireless client but, I can associate a wireless client to it.
The AP manager and Management interfaces, under PHYSICAL OPERATION are configured for port 1, which is the port that connects the Controller to the rest of the network. Since the whole network is using VLAN 1, I set the VLANs for the Management interface and AP interface to 0, untagged. I noticed when I set the AP manager interface to 1 I get the same results.
View 5 Replies
View Related
Feb 12, 2013
I am using webauth and need to install a SSL cert to prevent the "There is a problem with this website's security certificate" message. I have a Wildcard cert that was issued by Network Solutions that I use on a couple web servers I run, and want to know if I can use that for the WLC? It's a pks cert and I think the WLC needs to use a pem cert, so I converted the wildcard to pem. Or do I need to purchase a cert that is not a wildcard and is in pem format?
View 7 Replies
View Related
Apr 12, 2012
We are trying to get the waep template (default no changes) from the Cisco WebAuth bundle to work on a 5508 controller.
We've setup the controller to use the custom login.tar that comes with the waep template folder in the bundle. We setup the WLAN to work off the global template and we used the config network web-auth secureweb disable command to allow only http rather than https (which is supposed to work in 7.2 code)
When we test with the custom bundle, we get no answer from the controller, just a url of [URL]
If we turn custom off, and use internal everything works...
Just to be clear.. we aren't looking for authentication (user and pass) we are trying to do the enter your email and click accept to the aup method.
View 5 Replies
View Related
Sep 8, 2011
how can i remove webauth files from WLC?I have few versions of login.tar file used for web-authentication. After uploading a new login.tar file, the wlc still show old webauth bundle files. I tried to remove customized webauth login from wireless LAN, issue clear webauth-bundle and show>custom-web webauth-bundle WebAuth Bundle does not contain any files but when i upload new login.tar that does not include files from previous login.tar, i still get the old webauth. Is it possible to delete extracted webauth files from the controller using CLI?
WLC is running 7.0.116.0 code.
View 8 Replies
View Related
May 30, 2012
I am trying to upload a customized web-auth bundle to a WLC 5508 and having some issues.I have downloaded the web-auth bundle from Cisco and used this as a template to create the web pages.I seem to recall that there is only a couple of Windows tools that you can use to TAR the file such as TUGZIP and IZARC. Anyway I have tried both and I still cannot get the file to extract. I have tried to strip the file out so that I only send up the login.html page and even this does not work.I am using a software release 7.0.220.0.
View 6 Replies
View Related
Nov 16, 2011
I've installed a Cisco Wireless LAN Controller (4402) with six access points (AIR-LAP1131AG-E-K9) and created two WPA2 protected WLAN SSID's (e.g. internal and guest) and everything works fine.
The WLAN SSID named Guest, should be used for externel people. This SSID aditonal WebAuth. This also works fine, the guest receive a WPA2 key and username/password for WebAuthentication. But this works at this point only when they user WirelessLAN.
Now my Question: Is it possible to provide the setup also to the wired network using the WLC?
View 1 Replies
View Related
Jun 9, 2013
how to replace an image in webauth-bundle on WLC 5500?When I run "show custom-web webauth-bundle", I do see the files:
aup.html
login.html
yourlogo.jpg
But, the size of yourlogo.jpg is too big and need to replace with a smaller one.I have tried (with the appropiate IP and filename):
transfer download mode tftp
transfer download datatype image
transfer download serverip tftp-server-ip-addres
transfer download filename {filename.jpg | filename.gif | filename.png}
but, it does not work.
View 5 Replies
View Related
Apr 20, 2010
I have been trying to upgrade my WLC 2106, but it is stuck at rommon/grub mode.The steps are as follows
rommon #5> tftpdnldROMMON Variable Settings: ADDRESS=192.168.100.1 SERVER=192.168.100.10 GATEWAY=192.168.100.10 PORT=Ethernet0/0 VLAN=untagged IMAGE=AIR-WLC2100-K9-6-0-196-0.aes CONFIG=
[Code].....
View 4 Replies
View Related
Apr 10, 2012
We recently purchased a bundle of 3 1042N AP's with a 2106 WLC. I am able to get the controller on the network and am able to manage it through the https web gui. I am now trying to add one of the AP's to the controller and am getting an infinite loop on the AP upon bootup. I tried looking up the solution but could not find a good article that pertained to the problem I was having. One thing I did notice is the time on the AP is way offset, but when I do a clock set to change it to the actual date it doesnt stick on the next reload.
Here is the output:
using ÿÿÿÿ ddr static values from serial eeprom ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
[Code].....
View 10 Replies
View Related
Jun 19, 2011
I hava installed a WLC 2106 with 4 1252 Aps. Some laptops has dual radio wireless card, but others has just 2.4 Ghz card.
I have one SSID with WPA2/AES and 802.11X authentication.
With the laptops with dual radio the speed is in 300 Mpbs, but when is single 2.4 radio the max speed is 70Mpbs
If i use a 1252 ap with autonomous IOS, SSID with WPA2-PSK/AES this laptops single in 2.4 works to 144 Mbps
is there a knowed issue about 802.11x in 2.4 Ghz or i need to make a different configuration to can work in 2.4 with a speed of 144 Mbps?
View 2 Replies
View Related
Jun 9, 2012
I got my final assignment from school, and my teacher asked me to configure 2 Access Points (1200 series) directly on a Wireless Controler (Cisco 2106). I can't ask my teacher for any questions, cause he doesn't know how to configure it also, THAT's why he's asking me to do it.I've learned a lot of things about the default static interfaces (the "management" and "ap_manager" interface), but i can't seem to fully understand how to configure it.I want to use the Internal DHCP server of the WLC. How I can get those 2 Access Points working on the WLC. I only seem to get DHCP issues.
This is what i've done:
- Leave the configuration of the "management" and the "ap_manager" default (172.16.1.30 and 172.16.1.30). Bound to port 1
- Made a new interface "AP1" with IP-Address 10.0.0.10 (/24), default gateway 10.0.0.1. Primary DHCP server: 172.167.1.30
- Made a new interface "AP2" with IP-Address 192.168.1.10 (/24), default gateway 192.168.1.1. Primary DHCP server: 172.167.1.30
- Made 2 DHCP scopes within the 192.168.1.0 and 10.0.0.0 networks.
For some reason, when i boot up both AP's, the won't get any DHCP address.
View 13 Replies
View Related
Mar 18, 2013
I had a 2106 running 4.x software. It was upgraded to 7.x but will not read the config. How to downgrade the software?
View 4 Replies
View Related
Dec 2, 2012
We have a 2106 that was configured by a former employee. No one left in the company is qualified to configure it. The wireless guest access used to work fine. We'd configure a guest user account. They would connect to the guest wireless, open a web browser and login. For some reason now there is no prompt for login. People can connect to it and get an IP address, but that's it. No login prompt or anything else from there.User Login Policies was set to 0 and I put it to 8. That didn't do anything. Under Web Auth > Web Login Page it's set to Internal (Default).
View 5 Replies
View Related
Jul 7, 2011
I setup a mini wireless LAN network lab with a not for resale 2106 wireless lan controller and a sales air-lap1242ag access point. I do not have a DHCP and DNS in my lab environment. I have configured the WLC with the basic configuration using the CLI wizard, i also configured the WLC as a DHCP server for clients that will be connecting to the APs associated to the controller.
I powered up the AP and connect the ethernet port directly to the controller, the controller issued an IP address to the AP, the AP downloaded a new operating system from the controller but failed to join the controller.
I check both debug message on the controller console and the trap messages on the controller's GUI and it say the AP could not download a configuration from the controller and it is beacuse of invalid license. Below is the trap message:
Configuration Phase Statistics Requests ReceivedResponses SentUnsuccessful Request ProcessedReason For Last Unsuccessful AttemptLast Successful Attempt TimeLast Unsuccessful Attempt TimeLast Error SummaryLast AP Message Decryption FailureLast AP Connection FailureLast Error Occurred Last Error Occurred ReasonLast Join Error Timestamp
Also, I tried to log into the GUI of the AP using the both the username and password ''Cisco'' but I cannot get into the device. I can only get in through the CLI. In the CLI, almost all the commands I enter gives an error the it is disabled. I don't know what to do any more, I want to know if the access point is faulty or i am not doing the right thing.
View 4 Replies
View Related
Mar 4, 2010
I have a WLC 2106 and 1242AG.it's a hotspot configuration.So in WLC, under controller tab, i have set my ap-manager ip, my management ip, my virtual ip (1.1.1.1) and my hotspot network range ip.I set also a DHCP range for the hotspot network.
In Wlans tab, i set my hotspot wlan, with no layer 2 security and for layer 3, i set none for layer 3 security and i use web policy authentication.I use local authentication and i created under security menu, under AAA tab, 3 local net users.
From pc number 1, i get ip from dhcp, and i have authentication web page, authentication is ok and i can surf on web.From pc number2, when user 1 from pc 1 is connected, i get ip from dhcp but i have not the authentication web page, i have not DNS resolution.when i try https:1.1.1.1/login.html, i have no answer.
And when user 1 is de-authenticated, the user 2 can surf on web.So only one user can surf at the same time. not good for a Hotspot.
View 12 Replies
View Related
Oct 23, 2011
I have a problem with Cisco WLC 2106 (SW: 7.0.98.0) and LAP1262. The client roams to new AP, associates with the new AP and authentication (WPA2 with EAP-TLS) runs fine until WPA2 key exchange.
The first WPA2-Key-paket from AP (1 / 4) is sent twice. On a closer look at those packets with Wire shark, i've found out the first is encapsulated into a 11n-frame (A-MSDU). The resent frame isn't. This figure shows the first WPA-Key-packet:
The next figure shows the 2nd key-packet, without 11n-encapsulation: The problem, that occurs a very long roaming-time with about 5 seconds. As you can see on second figure, the second wpa-key is sent 5 seconds after the first.
Some details:
Client: Tablet PC with Intel 6230 agn
Controller: Cisco WLC 2106
AP: LAP 1262
Controller SW: 7.0.98.0
Encryption: WPA2-AES
Authentication: EAP-TLS
This problem occurs just on 5-GHz interface with 40 MHz channel bandwidth.
View 4 Replies
View Related
Jun 6, 2013
I have been having problems with a 2106 WLC which seems to have developed a fault. I cannot console into the device (although I can console into the ap1131ag showing no fault with the RJ45 - 9 Pin) and the device is no longer showing up in any of the possible I.P ranges.
Its showing a power light and a status light on the front panel, the Ethernet ports light up like a Christmas tree when a device is connected and the power supply is putting out a solid 47.7v.
Has anyone experienced anything like this before and can anyone suggest anyway of breathing life back into it?
View 5 Replies
View Related
Jul 6, 2011
I have a very basic WLAN setup with a 2106 controller and 3 (will be 4) 1140 APs.As part of securing the network I have been testing the rouge detection. The system has no trouble detecting and shutting down honeypots. I would like to also automatically shut down Rouge on Wire points. The system sees my test AP just fine. And I have it completely open (no security). But the system never detects that the rouge is on our network so no action is taken. I can connect just fine to the test AP with no encription using DHCP and communicate with everything on the network just fine.Is there some setting I am missing that allows the APs to detect that an AP is on wire?
View 2 Replies
View Related
Sep 10, 2012
Can I configure a mobility groups between 2106 Wireless LAN Controller and 5500 Wireless LAN Controllers?
View 8 Replies
View Related
Oct 17, 2011
I have a WLC 2106 with 3 APs. Everything works and users can connect, but the throughput seem to be lower than it should (it is around 8Mbps and should be around 30-50Mbps). And all speed and duplex has been accounted for.
I am trying to understand the stats that I see for the 802.11 MAC counters I under the Wireless APs.on the controller.
That screenshot is attached. I see high numbers for the following areas:
- Tx Failed Count
- RTS Failure Count
- FCS Error Count
what these mean and what could cause this? Maybe these are normal and not a concern.
View 1 Replies
View Related
Oct 15, 2008
basic question regarding the switchports on the rear of the 2106 controller. How do I configure them for use? I'm using port 1 as my uplink to a trunk port on an ASA and my network traffic to the management interface and guest vlans is all working as expected, but when I plug anything into any of the other ports, they get no addresses from my dhcp server (the ASA). I see nowhere to configure which vlan to tie the ports to or anything. I suppose I'm more used to a catalyst or ASA where I can just pick the ports and vlans (or trunks) I want to attach them to. [code] Again, all of the existing network functionality (private and guest network) is all functioning fine so I'm pretty confident I have the above configured correctly, I just cant make any progress on the WLC ports 2 - 8.
View 13 Replies
View Related
Apr 17, 2011
I have the following equipment
1 x AIR-WLC-2106-K9 (IOS = 6.0.199.4)
4 x AIR-LAP1131G-E-K9 (IOS = 12.4(21a)JHB1)
All configued ok with 2 SSID's associated to 2 VLANS all operates as expected.However every few 2 to 12 hours the WLC crashes, locks up.Unabale to contact via telnet or browser, will not respond to ping.The LAPs remain up but the WLANS go off air etcOnly a physical restart of the WLC will bring it back.
View 14 Replies
View Related
