how to replace an image in webauth-bundle on WLC 5500?When I run "show custom-web webauth-bundle", I do see the files:
aup.html
login.html
yourlogo.jpg
But, the size of yourlogo.jpg is too big and need to replace with a smaller one.I have tried (with the appropiate IP and filename):
transfer download mode tftp
transfer download datatype image
transfer download serverip tftp-server-ip-addres
transfer download filename {filename.jpg | filename.gif | filename.png}
how can i remove webauth files from WLC?I have few versions of login.tar file used for web-authentication. After uploading a new login.tar file, the wlc still show old webauth bundle files. I tried to remove customized webauth login from wireless LAN, issue clear webauth-bundle and show>custom-web webauth-bundle WebAuth Bundle does not contain any files but when i upload new login.tar that does not include files from previous login.tar, i still get the old webauth. Is it possible to delete extracted webauth files from the controller using CLI?
I have a new WLC 5500 series which i upgraded to a newer version. We got brand new AP's 1242 from Cisco. My ex-colleague had said that we can pre-image the AP's using the controller, so the new AP's get the image directly from the Controllers.
I have the following devices with me for this: A WLC 5500, 1242 AP ( 12 No.'s) and a 2960 switch. I tried to create dhcp pool in wlc so the ap get the ip and gets the image . However, i cant see the ap appearing in wireless tab. The WLC & AP will be connected to this same switch.
What configuration needs to be done on the WLC & the Switch so that the 1242 AP's when connected physically to the ports on the switch will get the image from the WLC.
I have 5500 controller with firmware 7.0 installed from the factory. Due to some reasons, I understood that other existing wireless infrastructure runs on firmware 6.0, and hance i need to downgrade the 5500 series to 6.0 . During the bootup, i could see there is another image called backup recovery image, which is running on version 6.0. How can i reboot controller to use the older image , which is from backup recovery image. I couldnt find it in the configuration guide.
We are now using image 8.0(4) for my ASA 5510. Later on, I would like to upgrade the image to 8.4(3).May I have to know what difference for those images, what should I take care of the script?
Is it possible to use both LDAP (to Active Directory) authentication for a WLAN defined on a 5500 series controller, and use the local user account database (AAA) for the guest vlan?
In my network:- at HO: 2 x WLC 5500 and 20AP, ACS, AD- at branches: 5 AP at each branchI configure the H-Reap. Now, I have some question about Cisco wireless:1. Only 1 Wan link between HO and branches, How I should configure when the WAN link down, all AP at branches still works, users still connect?
2.Based my network architecture, I should authentication central at HO or authentication at HO and branches? AP at branches supports local authentication or not? If we want to authenticate on AD at branches, how can I configure?3. I also want IT at branches have managed AP at their branches. When branch has visitor, IT at branch create temporary key and provide to visitor. at branch, how can I do that?
I currently have a asa 5500. is there a way to authenticate based on mac address throught the vpn client. We are haveing problems with useres using there home computers to connect. Yes they are smart enought to install the client and copy the profile.
i tried to create a customized web-authentication page that will re-direct any user to the web-page once they are connected to the network.
The problem is, i just cant attach/upload the image of the logo into the customized web-page (welcome/login page).Been researching about it, found and tried some clue bout it on cisco documentation, but still can't solve the problem.
I upgraded the IOS on my 887VA router which is not yet in service. The next day I did a cold boot and made some changes. Then, when I wrote them this warning popped up which seems to imply I need to recreate my configuration from scratch in order to avoid potential issues.Is that the correct interpretation of this message/scenario? [code]
On previous cameras (eg: the 932L) we could enable the FTP function to send a snapshot image every xx seconds, set a base file name, and set the Overwrite file function. On the 942L, this functionality appears to have been removed from the code. How I can get the 942L to FTP the current image every xx seconds and overwrite the file on the destination? (just like the previous cameras) Perhaps there is a new way and I can't find how to do it?
I am trying to upload a customized web-auth bundle to a WLC 5508 and having some issues.I have downloaded the web-auth bundle from Cisco and used this as a template to create the web pages.I seem to recall that there is only a couple of Windows tools that you can use to TAR the file such as TUGZIP and IZARC. Anyway I have tried both and I still cannot get the file to extract. I have tried to strip the file out so that I only send up the login.html page and even this does not work.I am using a software release 7.0.220.0.
I would like to get webauth bundle sample to create custom page for our AP controllers but I'm unable to find the sample .tar within the WCS itself.Some other WCS manuals has references in them that says there should be link to download sample from WCS but clearly 2106 hasn't got one.There's one in download section "webauth bundle 1.0.2.zip" but this is for registered partners and costumers, we are not registered as partners and cannot download the sample ourselves.
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
I was trying to implement stickiness based on cookie. Server inserts a cookie and sends it to the browser. I learned from app team that this cookie is changing dynamically during the session, so stickiness based on server’s cookie doesn’t work.
Now I want to investigate into possibility of ACE to insert a cookie. My question is: ACE feature of “cookie insert”: does it add additional cookie into http header without removing server cookies or it deletes the cookie(s) that server put into http header and replaces them with its own cookie?
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
I have a new fresh 5508 release 7.0.98.0 When I try to download (I mean upload to the controller) a customized Webauth bundle in .tar format I have the following message error in the syslog :*TransferTask: Oct 29 12:56:08.894: %UPDATE-3-UNTAR_CMD_FAIL: updcode.c:2832 Error during untar of webauth bundle. Tar returned 256.
I have been given a task to upgrade 8T1's bundle to DS3 Fractional circuit. We are currently using 2821 router with 4 VWIC-2MFT. What card/module I need to order for upgrading to fractional DS3. Also are there any compatability issues with ISP or local router.
What is the command that can show the ACE Bundle (Like: ACE-4710-02-K9, ACE-4710-04-K9). We have ordered one ACE with 4G BW, and another one with 2G BW. But nothing shows this fact using "show hardware" and "show inventory" commands !
I need to understand security bundles. I purchased a Cisco Security Bundle, Advanced Security, 64F/256D. part number CISCO3825-SEC/K9. My expectation from this device was that I will get an IOS based firewall with no need for an additional firewall module. however, the supplier is telling me that I have to buy a firewall module to use the feature. Isn't the bundle supposed to come with all I needed since is a bundle?
Is there any command I can use to verify if this device is really what I paid for? what can can I check for in the sh inv and sh ver commands? I don't see any information from these commands.
To understand and configuring VPN setup to give secure access to my DB & Application Server exist in my Datacenter, to other Service Provider organisation. They need to access those DB & Application Server sitting at their company LAN itself.
All the DB & Application Server connected to Distribution Switch in various VLAN,The Server support team from another company need the access to those, for that we will take MPLS link connecting out Core Router.
I'm going to be wiring a new (to me) house with a couple cat 6 runs to each room. The runs will all be brought back to an enclosed 6u rack and cat 6 110 style patch panel. This rack will contain:
Since the rack is completely metal and enclosed I'm going to put my Netgear WNDR3700 WiFi router (used as an access point only) on top of the rack. My question is, what the implications are in regards to placing a WiFi device right next to a bundle of ethernet cables?
We have ordered the following 10 line items , but only got 3 licenses , unless the 3 licenses somehow have all the licenses integrated into the 3 part numbers below, but I suspect not.
Licenses attached from Cisco:-
N7K-C7009-XL-SBUN Nexus 7009 Scalable Feature License x 1 N7K-C7009-SBUN-P1 Inc LAN,ADV,TRS,EL2,DCNM,DCNMSAN,MPLS,SAN,XL -Promotion x 1
Recectly we replaced Cisco 2100 Series LAN controller to Cisco 5508 Wirless LAN controller , I downloaded WebAuth Bundle from my Old LAN Controller ,when i am trying to upload to my New Wireless LAN controller ,its not uploading and also it gave me uploading failure error message .
I'm trying to replace a ASA 5505 with a Cisco 2801 w/ security bundle.I have gone through a pretty basic set up of configuring what I could and letting the Cisco Config Prof do the security audit to lock it down. I have everything working just fine except for the bandwidth.
As soon as I plug the router in it seems to give all the bandwidth to one computer and the rest of the campus slows down to a crawl.I turned on "fair-queue" and even tried the QoS wizard in CCP, but it seems like thats if you want to prioritize voice over data - which we aren't running VOIP so I don't need.
I have in the past downloaded the webauth bundle to a wlc 5508 running 7.0.98 successfully. I am trying to upload a new bundle after modifying the AUP but I get an error after the download to the wlc.
The error with FTP or TFTP is % Error: Webauth Bundle file transfer failed - Unknown error - refer to log
I've tried to copy the unmodified bundle from the zip and get the same error so I don't think it's the login.tar file.
I have a site which has been successfully running a multilink bundle of four T1 lines for about 6 months. The remote location is a C3825 router and the central location router is a C7206. I have access to both. A few weeks ago the multilink circuit started flapping and I was able to identify one of the four T1 lines as the culprit. When I shut down the interface for that one T1 line, the multilink circuit stops bouncing. As soon as I issue a "no shut" command on that fourth T1 interface, the multilink circuit starts flapping, ping commands start to time out and I have to shut it down again. The Telco has sent a technician to both locations and reported all tests run clean. Internal wiring from the NIU to the router has also tested fine. I've tried to move the T1 lines to different ports on both routers and the problem persists. [code]
I have a question about Cisco ASA 5505 firewall.We need 3 interfaces on the firewall , "inbound", "outbound" and "DMZ" , to control traffic between these zones.
Can we do this with Cisco ASA 5505 50-user bundle , or do we need to purchase Cisco ASA 5505 Security Plus bundle to get the DMZ zone working.
We have 4 data T1s providing our office with 6Mbs of internet bandwidth.I have been trying to track down the reason(s) for the steadily increasing frame and abort errors on the Multilink interface of our new router.We have a new 2961 with 2 2 port T1 interface cards (VWIC2-2MFT-T1/E1).
At first it looked like the T1s were completely clean, but after diving down a bit the last of the 4 T1s does appear to have a decent amount of slip and error seconds.Is that something that would cause the Multilink interface to show input, frame, and abort errors?Any config or debug commands I should start with to narrow down what might be causing this problem?
Config snippets:
card type t1 0 0card type t1 0 1!controller T1 0/0/0clock source internalcablelength short 440channel-group 0 timeslots 1-24description HCFD-XXXXXX!controller T1 0/0/1clock source internalcablelength short 440channel-group 0 timeslots 1-24description HCFD-XXXXXX!controller T1 0/1/0clock source internalcablelength short 440channel-group 0 timeslots 1-24description HCFD-XXXXXX!controller T1 0/1/1clock source internalcablelength short 440channel-group 0 timeslots 1-24description HCFD-XXXXXX!interface Multilink1ip address X.X.X.X 255.255.255.252ip nat outsideip virtual-reassemblyppp multilinkppp multilink group 1ppp multilink fragment disable!interface Serial0/0/0:0description T1 : HCFD-XXXXXXno ip addressencapsulation pppppp
I found this reference DCNM-L-NXACCK9 in the configuration generated by a dynamic Tools for a nexus bundle N5K-C5548UP-B-S32. This reference is not reflected in the price list. Has it been replaced? no datasheet on Cisco portal.
I am trying to upgrade a brand new ISE 3395 from 1.0.3.337 to 1.0.4 (latest). It keeps failing with % Manifest file not found in the bundle Here is the output:
company-ise-01/admin# application upgrade ise-appbundle-1.0.4.573.i386.tar.gpg ftp Save the current ADE-OS running configuration? (yes/no) [yes] ? Generating configuration... Saved the ADE-OS running configuration to startup successfully Initiating Application Upgrade... % Manifest file not found in the bundle
[code]...
I can't find anything about this for ISE, although there are a lot of topics for the same error for ACS.
We have ordered a N5548UPM-6N2248TP bundle. We would like to know if FET-10G sfp’s are included in this. let me know the difference between N5548UPM-6N2248TP and N5548UPM-6N2248TF bundle.
