Cisco Wireless :: 5500 - Authentication Central At HO And Branches?
Mar 10, 2013
In my network:- at HO: 2 x WLC 5500 and 20AP, ACS, AD- at branches: 5 AP at each branchI configure the H-Reap. Now, I have some question about Cisco wireless:1. Only 1 Wan link between HO and branches, How I should configure when the WAN link down, all AP at branches still works, users still connect?
2.Based my network architecture, I should authentication central at HO or authentication at HO and branches? AP at branches supports local authentication or not? If we want to authenticate on AD at branches, how can I configure?3. I also want IT at branches have managed AP at their branches. When branch has visitor, IT at branch create temporary key and provide to visitor. at branch, how can I do that?
View 5 Replies
ADVERTISEMENT
Mar 27, 2012
Should I trunk the port to the AP or not. I have a WLC 5508 in the head office and have AP in the remote office. I do not want traffic in the remote office to traverse the wan back to the WLC. I want the users at the remote office to use the local sub net at the remote site.
Should I then trunk the AP port on the switch to the AP as I have multiple ssid's with different sub nets?
View 3 Replies
View Related
Mar 4, 2012
I have followed the steps in this document in detail: URL
however, my central authentication does not work. I get to the guest portal, i get authenticated through the guest portal, but then the "second" MAB authenticatino doesn't happen. In the last screencapture of the document, you get a green "Dynamic Authorization" line (third line from below). On my system this is a red line with the error message "11213 No response received from Network Access Device". (i have a successfull guest authentication in my ise logs, but it seems ise is unable to bounce or initiate the second MAB.
View 2 Replies
View Related
Mar 27, 2012
on the followup the document "Configuration example : central web-authentication with a switch and Identity Service Engine" by Nicolas Darchis, since the redirection on the switch is not working.
I'm using ISE Version : 1.0.4.573 and WS-C2960-24PC-L w/software 12.2(55)SE1 and image C2960-LANBASEK9-M for the access.
The interface configuration looks like this:
interface FastEthernet0/24
switchport access vlan 6
switchport mode access
switchport voice vlan 20
ip access-group webauth in(code)
View 12 Replies
View Related
May 5, 2013
Is it possible to use both LDAP (to Active Directory) authentication for a WLAN defined on a 5500 series controller, and use the local user account database (AAA) for the guest vlan?
View 1 Replies
View Related
Jun 9, 2013
how to replace an image in webauth-bundle on WLC 5500?When I run "show custom-web webauth-bundle", I do see the files:
aup.html
login.html
yourlogo.jpg
But, the size of yourlogo.jpg is too big and need to replace with a smaller one.I have tried (with the appropiate IP and filename):
transfer download mode tftp
transfer download datatype image
transfer download serverip tftp-server-ip-addres
transfer download filename {filename.jpg | filename.gif | filename.png}
but, it does not work.
View 5 Replies
View Related
Feb 10, 2011
I currently have a asa 5500. is there a way to authenticate based on mac address throught the vpn client. We are haveing problems with useres using there home computers to connect. Yes they are smart enought to install the client and copy the profile.
View 1 Replies
View Related
Jun 18, 2011
I am having asa 5520 in my head office and in branches 2811 routers.i connected two branches with my HO through VPN.now i configured remote vpn client in HO asa . now i need to access all the branches using this remote client.how i create route in HO ASA.
View 7 Replies
View Related
Aug 16, 2012
The network scheme is this one, I have Lightweight APs distributed and a pair of WLC 5508 centralized. We use a pair or SSID for all the branches, concretely Voice and Data.
All the branches has a local DHCP Win2k3 Server, and APs get its IP address correctly from the local DHCP, but the wireless clients obtains the IP address from the centralized DHCP Server, because all the DHCP traffic go through LWAPP/ CAP WAP tunnel to WLC.
I want that the clients get its IP address from the branch DHCP, i have reading and i think that we need to use H-REAP with local switching configuration and the correct vlan mapping in local switch and H-REAP for it works that we want. Is it correct? Is possible that the client obtain the IP address for the local/branch DHCP Server instead of the Local DHCP?
View 6 Replies
View Related
May 1, 2013
1) Virtual controller 7.3.112 is OK
2) N° 2 LAP 1130 e 1240 is Joined to controller OK
3) flexconnect in localswitch is OK
4) flexconnect in central switch IS NOT work.
View 3 Replies
View Related
Mar 7, 2012
We are in the process of evaluating Cisco wireless controllers and AP. We have 3602 APs and 2504 controllers right now. We have multiple branch offices connected to the main office through layer 3 and they all have different vtp domains and vlans. I am trying to deploy APs at the branch offices and connect them back to the controller and the central site. I created a sub interface and ssid with one of the vlans at the branch office on the controller and was able to get the AP to join the controller through DNS. However, a client at the branch office connected to the AP was unable to ping anything at the branch and central sites. Any documentations on how to deploy such a setup where the controller is at the central site and AP at the branch office going through multiple routers in between?
View 1 Replies
View Related
Nov 10, 2012
Samsung CY-WDCA7UT/ZA USB Central Station Dongle driver?
View 1 Replies
View Related
Jul 23, 2012
I want to implement site to site vpn among our Head Office and Barnch routers (300 Sites).Head Office Site I have a cisco 7200 Router Im going to terminate the VPN conection on that.Branches we are having cisco 1841 series routers. They all are capable of working with VPN.In the present it is act like a EazyVPN Server for selected sites(30 sites).Is there any license limitations in Cisco 7200 Router ?Can I run both Site to site VPN and Eazy VPN Server together ?
View 1 Replies
View Related
Nov 24, 2011
Trying to change my IP address in windows 7. I downloaded Desktop Central 7.Server and Desktop Management Software: Now what am I suppose to do?
View 2 Replies
View Related
Mar 21, 2012
I'm working on a small scale Cisco WAAS deployment. I want to know if it's possible to use the entry level Cisco WAVE-294-K9 as Central Manager.Also about licensing, does this appliance model come with the enterprise level license
View 2 Replies
View Related
Apr 26, 2011
I am looking for a Best Practices or a few places to pay attention to in the Cisco ESW-520-48P switch I have. My VoIP solution is RingCentral, and while they are Cisco phones, I've been hestitant to setup VLANs etc. the way I am used to. Plus setting up Auto QoS seems different than what I am used to with a 3750 switch.
Right now I've left the Smartports Wizard alone, and none of the ports are configured. There are no VLANs or QoS on the LAN currently.
What I was running into were calls cutting out where one side wouldn't hear the other anymore, but the call would remain connected. However, this has happened in this small 15 person office, when there is only one employee here after hours, talking on the phone. There isn't any heavy network traffic, because I have network monitoring showing me low usage (no streaming music, videos, or anything else).
This switch has a Gb connection to a Linksys SR2024 (the server switch), which is also set at Factory Defaults. I mention that because I recently bypassed the ESW-520-48P, and plugged one phone into that switch and the RingCentral phone worked fine for outside calls.
Is there something besides QoS that I should look at in the ESW-520 switch that might be causing a checkpoint of some sort, or interrupting VoIP traffic that I need to configure or disable?
And are there any Best Practices or scenario guides for this switch? I found the Admin Guide, but it really just explains every option in the GUI for the switch. And it seems all of my CCNA training isn't working with going in and quickly troubleshooting this switch besides knowing that something in it could be hanging it up.
View 6 Replies
View Related
Jun 13, 2011
I'm planning to use this card for a 7204VXR with NPE-G1. I'll be using it for data in the customer data center; in remote sites customer has 2811 with VWIC-2MFT-E1T1, so I assume it's using a framed E1 (g704-->1984Mbps). Can I use PA-MC-8TE1+ in the central site? How will the configuration look like in the central site?
I have seen this PA is the only one available for 7204 VXR, so I assume it supports all the E1 configurations, am I right?
View 2 Replies
View Related
Nov 22, 2011
I have got cable modem and its output is connected to netgear router n150 wireless router model wnr1000v2.now 3 desktops and one laptop is wired to that router through 4 lan ports. now i need to access internet from all systems.and also make one system as central database so that everyone can share and use all work files.one printer is connected to one system.i also need to print docs from all systems.
View 1 Replies
View Related
Aug 20, 2011
How could i make a vpn tunnel between a router SA520 and a central UC540.
View 3 Replies
View Related
Aug 7, 2011
I'm running v4.3.5 in our WAAS environment. At the CLI of one of our 7341 WAEs, there are several connections that show up [code] However, in the Central Manager nothing shows up - not even empty graphs - when I click on a device and go to monitor/connections statistics. After a few minutes, I do get an error message that states "Error retrieving connection stats. Please ensure that the device is online and then refresh." By the way, I get all other statics in the GUI such as Optimization Details Report, Traffic Summary Report, etc. Another thing, these WAEs are behind a router and supposedly the ports to allow access to/from the WAEs and other data is allowed through the firewall.
Is there some special port that needs to be opened on the firewall to allow for 'connection statistics' information displayed, that doesn't need to be opened for the other statistics to display? Or could this be a bug in the software?
View 1 Replies
View Related
Jul 15, 2012
I have a old Cisco/linksys router that I want to do a complicated setup with.Heres my current situation.I currently have my computer and laptop linked into my home network over wireless as running a cable to the hub gets in the way of other door ways, But when playing networked games i run the cable as its only for a short time and people can cope with that,However I have recently gotten into minecraft server hosting, and I have previously just Run two cables to the main hub so I can host the server on my desktop and play on my laptop.So here is where is gets complicated.I found my old router and set it up as a central hub for my room, with the laptop and desktop going into that, then one cable going to the hub,However, I am spending alot of time messing around on the server and would like some way for me to connect to the server from my laptop without having to go though the central hub, just using this sub router. But I still want my IP to stay the same when i reconnect to the main network so when my brother and other friends want to play I can connect to the main network and host over that without having to change my server settings for the new IP.
View 2 Replies
View Related
May 5, 2011
Equipment Cisco1921, HWIC-1ADSL, 2 x GB Ethernet interfaces (Only one used for local LAN) Software IOS Version 15.1(1)T2..I have been asked to configure this router to provide an IPSEC tunnel back to our central office.We have been provided with an ADSL business class 7MB service from Telecom Italia, they have presented the circuit to our office with no terminating equipment (wires only). Telecom Italia have provided us with some IP addressing information as follows (I will not disclose the entire IP address) [code]
I can see that the packet count is increasing both inbound and outbound on the ATM interface. I have read many documents and tried many different way to try and get this resolved, I even logged a call with Cisco but no dice.
View 5 Replies
View Related
Aug 18, 2012
I bought 2 RV180 to setup a VPN tunnel between a remote site and central office.The VPN tunnel is established, I can ping from central office to remote site but browsing on that server fails. [code]
Seems the routing is not really working through the VPN Tunnel.
View 4 Replies
View Related
Feb 23, 2011
I have successfully connected my vpn to my central point and 2 branches.My branch can see central and visa versaMy problem is that i can't see from my 1 branch the other branch.
My central has RVS4000 and my branches has WRV200.How can i be able to access from my branch1 PC, my branch2 PC and visa versa
View 1 Replies
View Related
Jun 6, 2012
I have senario where 15 branches via bri connection to central ISDN E1 Pri Head office.The setup is working before and suddenly branches not able to dial head office.Below is the debug q931 logs from branch router and i am getting continous "channel not avalible message on Head office
Branch router logs
*********************************************************************************************
hmc#isdn test call interface bri 0/0/0 44492999
hmc#
007049: Jun 6 14:41:39.497 gmt: ISDN BR0/0/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
007050: Jun 6 14:41:39.721 gmt: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0/0/0, TEI 78 changed to up
007051: Jun 6 14:41:39.721 gmt: ISDN BR0/0/0 Q931: Sending SETUP callref = 0x002E callID = 0x84BC switch = basic-net3 interface = User
007052: Jun 6 14:41:39.721 gmt: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8 callref = 0x2E
[code].....
View 1 Replies
View Related
Apr 9, 2011
I have an Dell inspiron 1564 with dell webcam central I been useing it a while now and had no problems with it untill one day I logged on and I go on webcam chat sites and as you know theres a button you click for your cam to turn on and useally a warning sign would appear saying would you like to allow this site to acces your webcam and I would click allow but now nothing appears and i click the cam sign and nothing happens just black I set the settings to Allow and always remember but nothing will work I was told to get rid of all my toolbars as they might of caughts the problem so I did and now i don't have any toolbars but it's still in not working I think its the McAfee secuirty I have a on my computer that is not allowing it but then i think why would it one day just stop it from allowing.
View 4 Replies
View Related
Mar 12, 2013
I want to upgrade the WLC 5500 from 7.0.220.0 to 7.3.112.0, coul be any risk if i do the upgrade..?
View 2 Replies
View Related
Jan 16, 2013
I have a Cisco 5500 Software Version 6.0.199.4. Today I've been able to succesfully add a few newly purchased 1242G APs to my WC so I know everything is setup properly. They got the proper DHCP info and I was up and running in a few minutes.
I'm now trying the same thing with a newly purchased Air-Lap1262N-a-KP
I can read the bootup because I'm attached to it on the console.I see that it gets the proper IP#
But then I keep getting a "failed to decode the discovery response" error.
[code]....
View 9 Replies
View Related
Nov 19, 2012
We have a WLC 5500 connected to a 2960 acting as core switch. there is a server attached to the switch , bearing all dhcp pools for lan and wireless users. Can the wlc or the switch be configured in such a way that the wireless users associating to the wlc get their ip addresses from the dhcp pool configured on the server. Can the configuration can be shared for such a setup.
View 5 Replies
View Related
Jun 1, 2012
i have a existing wireless network setup in my office existing wlc in 4402 and LAPs are 1130 & 1242 all are working fine but we are now planning to use new 5500 series controllers for the same access points,i want to ask that how i can done this job with very minore downtime and users disconnectivity + zero error results??
View 2 Replies
View Related
Jul 15, 2012
Our client have cisco 5500 Wireless lan controllers. They connect to core switch and other ports conenct to various switches on each floor. Then we have cisco AP 1300 series mounted on celing. I was reading that lightweight AP gets config from WLC as soon as they plug in. Need to know how the AP gets config from WLC switches?
View 8 Replies
View Related
Jul 11, 2012
I have quick question here does AP BR1310 can be associated with WLC 5500?
View 4 Replies
View Related
Jan 30, 2013
I have a Cisco aironet 3502i access point which I am using with a 5500 Wireless Controller. I was configuring the AP for flexconnect and accidentally enabled PPPoE authentication - but never set configured login details for PPPoE. Now when the AP boots up it tries to use PPPoE but fails - it never even looks for an IP address. I have no way to get the AP connected to the controller again.I tried logging into the AP via console, the AP gives me output but I never get a login, even when I hold down the Mode button during startup.I also tried holding the Mode button and waiting for the AP to boot with its default IP (10.0.0.1) and connecting to the AP via telnet, but I was unable to connect or even ping with my PC on the same network configured as 10.0.0.2.What can I do to set this AP back to defaults, to become a normal DHCP client, and reconnect to the wireless controller where I can reconfigure it?
View 9 Replies
View Related
