Cisco AAA/Identity/Nac :: 2960 - Central Web Authentication With Switch Not Working
Mar 27, 2012
on the followup the document "Configuration example : central web-authentication with a switch and Identity Service Engine" by Nicolas Darchis, since the redirection on the switch is not working.
I'm using ISE Version : 1.0.4.573 and WS-C2960-24PC-L w/software 12.2(55)SE1 and image C2960-LANBASEK9-M for the access.
The interface configuration looks like this:
interface FastEthernet0/24
switchport access vlan 6
switchport mode access
switchport voice vlan 20
ip access-group webauth in(code)
View 12 Replies
ADVERTISEMENT
Mar 4, 2012
I have followed the steps in this document in detail: URL
however, my central authentication does not work. I get to the guest portal, i get authenticated through the guest portal, but then the "second" MAB authenticatino doesn't happen. In the last screencapture of the document, you get a green "Dynamic Authorization" line (third line from below). On my system this is a red line with the error message "11213 No response received from Network Access Device". (i have a successfull guest authentication in my ise logs, but it seems ise is unable to bounce or initiate the second MAB.
View 2 Replies
View Related
May 1, 2013
1) Virtual controller 7.3.112 is OK
2) N° 2 LAP 1130 e 1240 is Joined to controller OK
3) flexconnect in localswitch is OK
4) flexconnect in central switch IS NOT work.
View 3 Replies
View Related
May 17, 2011
I have configured the cisco 2960 switch with AAA & the radius server is free radius. I am able to login into the switch when radius server is working.But when radius server is not reachable, in that particular condition the switch doesn't move to local authentication configured on the switch.
aaa new-modelaaa group server radius radiuss server 10.1.0.215 auth-port 1812 acct-port 1813!aaa authentication login default group radiuss enableaaa authentication login CONSOLE localaaa authentication enable default group radiusaaa authorization exec default group radius if-authenticated
radius-server host 10.1.0.215 auth-port 1812 acct-port 1813 key 7 071F285C422948514117171
radius-server retransmit 2
line con 0 exec-timeout 5 0 privilege level 15 password 7 14341B1B7D6F0417626173455E47060F login authentication CONSOLEline vty 0 4 access-class 91 in exec-timeout 5 0 password 7 106D004F2C3B7B7F757E6A64812812d transport input sshline vty 5 15 access-class 91 in exec-timeout 5 0 password 7 106D000A061845jsajtqwkd327E6A64 transport input ssh
View 1 Replies
View Related
Oct 28, 2012
I'm trying to test such 802.1x wired environment:windows xp sp3 as supplicant windows NPS as radius server 2960 as authenticator latest anyconnect (3.1.01065) + nam and standalone profile editor.I have a question: What is the difference between protected identity pattern and unprotected identity pattern (set in nam profile editor)? As I understand documentation PEAP-MSCHAPv2 is a tunneled method and it uses un- protected identity pattern to protect user's identity during phase 0. But if I use any fake identity here (anonymous, anonymous@[domain], etc) access is rejected (Access-Reject in switch debugs). I have to use exacly the same pattern in unprotected identity pattern as in protected identity pattern ([username] or [username]@[domain]) to gain access, regardless of authenticaton mode (same in machine only, user only authentication).
View 1 Replies
View Related
Jun 21, 2012
[Env on my lab investigation]
supplicant - W7 with cert
authenticator - Catalyst 2960 with IOS 15.0(1)SE2 /newest/
authentication server 2x - W2008/NPS like a RADIUS server
The problem is the end station that are still connected to the supplicant port /use a EAP-TLS/ after the reboot supplicant! All of them will be put into the Guest VLAN instead of static VLAN 34!
[The question]
What is wrong and how to configure/tune and what authenticator or authentication server to prevent after the reboot to observe a authentication timeouts? Of course the supplicant after 20 minutes /next EAPOL start farmet put into VLAN 34.
[Code] ........
View 1 Replies
View Related
Aug 18, 2011
Find here the extraction of the configuration and the debug sysout. The radius servers works fine with all the other accesss like ssh, telnet...
Just the http access fail. This configuration work fine with the version 12.2.55 installed before.
Aaa new-model
aaa authentication login default group radius local
aaa authentication login physique local
[Code].....
View 2 Replies
View Related
Aug 14, 2011
I want to configure IEEE 802.1x port-based authentication on cisco switches, preferable 2960 series. Which models support this feature?. I have try with some older switches but it doesn't works properly on everyone. I have upgraded them whitout better results, there is namely an issue with TLS handshaking on some switches which produces authentication to fail.
View 1 Replies
View Related
Mar 10, 2013
In my network:- at HO: 2 x WLC 5500 and 20AP, ACS, AD- at branches: 5 AP at each branchI configure the H-Reap. Now, I have some question about Cisco wireless:1. Only 1 Wan link between HO and branches, How I should configure when the WAN link down, all AP at branches still works, users still connect?
2.Based my network architecture, I should authentication central at HO or authentication at HO and branches? AP at branches supports local authentication or not? If we want to authenticate on AD at branches, how can I configure?3. I also want IT at branches have managed AP at their branches. When branch has visitor, IT at branch create temporary key and provide to visitor. at branch, how can I do that?
View 5 Replies
View Related
Mar 27, 2012
Should I trunk the port to the AP or not. I have a WLC 5508 in the head office and have AP in the remote office. I do not want traffic in the remote office to traverse the wan back to the WLC. I want the users at the remote office to use the local sub net at the remote site.
Should I then trunk the AP port on the switch to the AP as I have multiple ssid's with different sub nets?
View 3 Replies
View Related
Aug 17, 2011
I have a dot1x client with client certificate working well with my ACS 5.2 and EAP-TLS. Now I would like to configure the Re-Auth periode on the ACS 5.2, I did the following:
1. Configure a Access Profile with Reauthentication Timer = static and 30 seconds (see attachment ACS1.png and ACS2.png)
2. Enabled authentication periodic and authentication timer reauthenticate server on switchport
interface GigabitEthernet1/0/x
description to dot1x clients
switchport access vlan 5
switchport mode access
authentication event fail action authorize vlan 998
[code]....
View 2 Replies
View Related
Mar 3, 2013
We have a configuration that work fine but one of the combinations it don´t work. When we connect a guest laptop, the first time work fine. The configuration is when the laptop don´t authenticates with radius, the dhcp server assigned vlan guest and ip guest. The first time was ok. After, We connect a laptop with users authenticates work ok, the radius asigned vlan of users and dhcp server assigned ip users. The problem was when we connect for two time a guest laptop, radius didn´t validate and laptop didn´t negociate ip with dhcp server. In this time, the administrator of dhcp server, tell us that they didn´t see nothing traffic of my mac. and anymore run fine. If Whe change the port of switch , the laptup start working again.
Radius=NPS
Server dhcp: is typical.
Our scenario is with a ip cisco phone. the ip phone don´t have the authentication. The administrator of radius tell us that the configuratation is fine and the configuration of dhcp is fine. When we connect only laptop, everything run ok.
Configuration Port.
interface GigabitEthernet1/0/3
switchport access vlan 202
switchport mode access
[Code]...
View 4 Replies
View Related
Mar 20, 2013
I am trying to get AAA Authentication working on a Cisco 2960-24pc-l running 12.2(55)SE5 IOS and cannot get it to work. I have it currently working on a Cisco 3750-24te-m running 12.2(55)SE IOS. Here is my config: [code]
When I login to the 3750, AAA is used. When I login to the 2960, the local username is used. Any thoughs here as to why it works on the 3850 and not the 2960?
View 2 Replies
View Related
Jan 10, 2012
I replaced an access switch 3750 with a switch 2960. Basically I just copy the whole config of the 3750 to 2960.
The 3750 use AAA, Crypto pki trustpoint TP-self-signed and radius-server host etc.
Now I can only telnet to 2960 but not SSH to it.
View 3 Replies
View Related
Aug 26, 2010
My switches are able to successfully authenticate user access against ACS 5.1 via SSH with TACACS+, but I am not able to authenticate via HTTPS with TACACS+. I don't even get a log in ACS when attempting to authenticate via HTTPS.
Here is my AAA config, followed by a debug:
aaa new-modelaaa authentication login ACCESS group tacacs+ localaaa authorization consoleaaa authorization config-commandsaaa authorization exec ACCESS group tacacs+ aaa authorization commands 1 Priv1 group tacacs+ none
[Code]......
View 8 Replies
View Related
Mar 29, 2011
I would like to make a centralized management of loggin account on my cisco switch (with a radius server). But, on Cisco 3750 E, i use 12.2(44) SE1 IOS and no command aaa authentication login exist.
Cisco 3750 can support other IOS than 12.2 who have this ability ?
View 2 Replies
View Related
Feb 4, 2012
I've recently been looking into linking in our Cisco 2960S Gb Switch with RSA SecureID via Radius.I've already managed to link it in for ssh access
but I've not managed to get it working for http / web access to the switchI think this is because we're using "single use" tokens for maximum security with RSA Secure-ID and the web interface attempts to authenticate multiple times against the Radius part of the RSA SecureID server (okay on the first authentication, but each time after it's going to want a different token code)
(if there's a way to get the switch to just authenticate once instead of multiple times against the radius server) For info the switch is a WS-C2960S-24TS-L with IOS 15.0(1)SE2
View 2 Replies
View Related
Apr 23, 2013
First, my configuration, (then the problem down below):
I have an Aironet 1142 with multiple SSIDs [mapped to V LANs] connected to Gi1/0/2 on a 2960 switch in a user-accessible area. This switch is up linked to another 2960 switch in a wiring closet, and the Microsoft NPS server is connected to the wiring closet 2960.
Aironet -- 2960 [user area] --- 2960 [closet] -- NPS RADIUS
I have the user-area 2960 configured as an authenticator switch for dot1x, and port Gi1/0/2 is authenticating the Aironet via MAB to RADIUS. RADIUS is sending VSA device-traffic-class=switch to the 2960. The closet-2960 has no special 802.1x configuration, nor is it an authenticator switch; it just has a manually-configured trunk port to the user-area 2960 [for now; I'm trying to take this one step at a time!].
The user-area 2960 correctly converts port Gi1/0/1 to a trunk port when the Aironet is authenticated [via MAB]. The Aironet boots up, the port is opened, I can ping the Aironet on the native V LAN, and all is well [so it seems]. The Aironet dot11Radio is configured for two SSIDs and mapped to V LANs, which are being spanned via STP thru the user-area 2960 and the closet-2960. STP is correct and verified on all switches.
I have DHCP snooping configured on the user-area 2960 but only for V LAN 1 [but NOT the wireless user V LANs], the trunk port to the closet 2960 is a trusted port. Hosts on the wired ports on the user-area 2960 are able to get DHCP IPs. On the Aironet, "show dot11 associations" shows hosts on the SSIDs are getting DHCP addresses. Again, I am *NOT* running dhcp snooping on wireless SSID V LANs [i read elsewhere that can cause problems as users roam between Aironets].
I do have CISP configured on the user-area 2960. I do not have CISP configured on the closet-2960 [best I can tell, that's not required at this stage, but I could be wrong]. Despite the alleged documentation, I could not get the Aironet to use a dot1x credentials profile to authenticate to NPS/RADIUS as an 802.1x supplicant, which is why I resorted to MAB for this exercise. The Aironet simply would not run dot1x [best I could tell]. The documentation and configuration didn't seem complex, so I was quite confused.
I have upgraded the Aironet to the latest 12.4(25d)JA2 software, and the 2960 is at 12.2(55)SE7 [i saw 12.2(58) has some issues, but I'm willing to be persuaded otherwise, based on sound advice]. Ok, now the problem:
Users on the guest wireless SSID (V lan 20) say they cannot connect. Yep, classic. V LAN 20 is trunk and spanned to all the sufficient places. The Aironet shows users in the associations list for that SSID with IP addresses from the DHCP server! DHCP snooping is not configured on that V LAN. I read another support forum post saying CISP and MAB could cause problems with "disappearing" ARP entries. I appear to have that problem. However, the user on the Staff wireless (V LAN 10) has full access. Am I running into a problem with "multi- host" authentication config? Via tcpdump on my firewall, I see nothing but broadcast and multicast traffic coming from a host on VLAN 20. What puzzles me is how I do see *SOME* traffic from a V LAN 20 host on this SSID, but no uni cast traffic!
Since you're going to ask, here is my port config for this AP on the 2960 authenticator switch in the user-area, and the AAA config pieces:
#sh run br | in ip dhcp
ip dhcp snooping vlan 1
no ip dhcp snooping information option
ip dhcp snooping database flash:dhcp_snoop.txt
ip dhcp snooping
[code]......
View 1 Replies
View Related
Jul 25, 2011
We have a Catalyst 3750 switch that failed over to local login after the Tacacs authentication stopped working. I went through the configuration settings and everything appears to be identical to another switch in this same building.
View 4 Replies
View Related
Jun 8, 2013
how ISE support on third party LAN switch, if the requirement is doing 802.1X based flexauth.Refer to the diagram i attached; 01 topology.png
Concern 1: if the 3com switch with 802.1X feature, but still without the full feature to support FlexAuth, policy encforcement, DACL etc. In this kind of situation, will user still able to authenticate (using method PEAP-MSCHAP v2), but authorization just grant with permit any any?
Concern 2: Can i assume i authenticated the 3com switch using MAB? But this will cause endpoint with no 802.1X, am i right?
Concern 3: cisco switch C4507-E, loaded with IOS version Cat4500e-UNIVERSALK9-M, version 03.04 and Supervisor Engine :WS-X45-SUP7-E, is this platform is supported in Cisco TrusctSEC?
View 2 Replies
View Related
Sep 18, 2012
WS-C2960G-24TC-L 12.2(25)SEE3 C2960-LANBASE-M
I would like to get the temperature status from this 2960 switch (and several other models. Normally this OID should be:.1.3.6.1.4.1.9.9.13.1.3.1.6 But it does not return anything.
The termperature status can be found from the command line by running:"sh env temp" This reports back ok, so I assume there is a temperate gauge in the switch.
This oid is part of the "CISCO-ENVMON-MIB" mib and accouding to the Cisco MIB selector it is supported on my switch and IOS - 12.2(25).
(Another thing I woudl like to monitor and should be supported is the fan status oid (.1.3.6.1.4.1.9.9.13.1.4.1.3). That doesn't return anything either.
What do I need to do to get the temperature environment status from SNMP query?
View 3 Replies
View Related
May 21, 2013
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
View 1 Replies
View Related
Jan 16, 2012
I configured before ACS v4.2 to authenticate network devices using internal users at first, and if the user is not found use AD list users. But with v5.3 I have some problems doing this, on identity policies I use rule based result selection option, I configured 2 polices for Identity source, one for Internal Users and other policy for AD user, but it only works with the first policy, internal users or AD, but works only for the first policy identity. how to do that, if the user is not found on first policy, continue to the next policy.
View 7 Replies
View Related
Jul 3, 2011
I need a specify users to allow access to particular devices and give privilege only for show command or show run. Here is how I tried to configured.
1. Configured two seperate Shell Profile and Command set with privilege level 4-5 and allowing only show run command
2. create seperate service selection rule with adding the require NDG and protocol TACACS and maching service "RestrictAccess"
3. In the RestrictAccess Service I have following configured; Identity: internal users, Group Mapping to a particular group where the user exists, authorization: matching the above created identity group, NDG, shell profile, command sets
All the steps are attached in the .doc file. However when I tried with the particular user he is able to access everything and he is not hitting the correct access rule.
View 6 Replies
View Related
Feb 25, 2013
I have a problem with radius authentication on catalyst 2960 with freeradius as radius-server. The Catalyst is behind a HP5412zl layer3-switch. The rest of the network are hp-layer2 switches, which do radius authentication to the same radius server. The ios on the catalyst is c2960-lanbasek9-mz.150-1.SE3. Apparently there are no requests made to the radius-server, since I dont see any requests coming in. Port 0/7 is voice port with laptop behind , /port 0/8 access-port with laptop directly connected.
config :
aaa new-model
aaa authentication dot1x default group radius
dot1x system-auth-control
!
!
!
interface FastEthernet0/1
[code]....
View 1 Replies
View Related
Apr 13, 2010
I have a Catalyst 2960 switch (2960-8TC-L) and running Software version 12.2(53)SE1.I mange to configure SSH to the switch and add addition user as well.Now I need to configure this switch password less log in with public key SSH authentication.
I configured several Linux servers and Workstations for the public key SSH authentication.So far I could not figure out how to do this in CISCO switch. Following link {URL} how to do this.But ip ssh pub key- chain command never work showed invalid command.
View 2 Replies
View Related
Nov 16, 2011
I have configured ssh on a 2960 to use public key authentication. Now that I can securely log into ssh without a password Is it possible to disable password authentication so that it is impossible to login without the key?
View 2 Replies
View Related
Nov 2, 2011
I am seeing the following behavior when computers move from one switch to another with dot1x ONLY when there is a 'stupid' switch in between.
computer -------- 'stupid' switch ------- 2960
dot1x is working fine but when the computer is disconnected, the port still shows the authentication session id so when the computer connects to another port or switch, authentication succeeds but traffic doesn't pass. While I'm almost certain that the culprit is the 'stupid' switch that doesn't clear the session id, I have already tried another one and the problem remains so I'm actually just asking for a confirmation that all these 'stupid' switches present this behavior and if there is a workaround in this case.
View 0 Replies
View Related
Oct 13, 2011
I am trying configure tacacs authentication for http in Cisco 2960 with IOS 15.0.1.SE. [code] But the device is not authenticating. It ask the credentials (user and pass) but not authenticates.
View 7 Replies
View Related
Apr 2, 2013
I am trying to get to work Web-based authentication on Catalyst 2960 and 3560 for clients that don't support dot1x. I followed this guide. Here's the problem: Client (win7) joins the network, opens the web browser and tries to navigate to any http site. The switch forces him the "login" page in which he has to enter credentials. After the client enters credentials, the switch sends http 500 internal server error page and nothing happens. Doesn't matter if the credentials were correct or not. Also i checked radius logs for requests, the switch doesn't even ask radius.
The configuration:
sh ip admission configuration
Authentication Proxy Banner not configured
Consent Banner is not configured
[Code].....
View 6 Replies
View Related
Feb 2, 2012
In order to restrict access to websites on our internal network, would we be able to put an ASA in front of the web server and force users to authenticate through the ASA and, once authenticated, allow only port 80 or 443 traffic for that use? The ASA would query the ACS 5.1 server for authentication/authorization using AD as the identity store. Is this even possible with TACACS?
View 1 Replies
View Related
Apr 1, 2012
My customer has a large installed base of MACs, all connected via controller-based (5508) WLAN. He wants to grant access to the network based on the device's mac addresses and move the WLAN-clients to a specific VLAN.I added all devices with their mac addresses to the ACS internal identity store for hosts.According to the following message the client sends the user-login credentials (chegger) within the RADIUS-request instead of the clients mac address and of course it has to fail. After many configuration changes, I ended up always with the same result.
View 2 Replies
View Related
Jun 13, 2012
I have question on EAP-TLS with ACS 5.2. If I would like to implement the EAP-TLS with Microsoft CA, how will the machine and user authentication take place? Understand that the cert are required on both client and server end, but is this certificate ties to the machine or ties to individual user?
If ties to user, and I have a shared PC which login by few users, is that mean every user account will have their own certificates?
And every individual user will have to manually get the cert from CA? is there any other method as my environment has more than 3000 PCs.
And also if it ties to user, all user can get their cert from CA with their AD login name and password, if they bring in their own device and try to get the cert from CA, they will be able to successfully install the cert into their device right?
View 7 Replies
View Related
