Cisco WAN :: Radius Authentication On Catalyst 2960?
Feb 25, 2013
I have a problem with radius authentication on catalyst 2960 with freeradius as radius-server. The Catalyst is behind a HP5412zl layer3-switch. The rest of the network are hp-layer2 switches, which do radius authentication to the same radius server. The ios on the catalyst is c2960-lanbasek9-mz.150-1.SE3. Apparently there are no requests made to the radius-server, since I dont see any requests coming in. Port 0/7 is voice port with laptop behind , /port 0/8 access-port with laptop directly connected.
config :
aaa new-model
aaa authentication dot1x default group radius
dot1x system-auth-control
!
!
!
interface FastEthernet0/1
[code]....
View 1 Replies
ADVERTISEMENT
Aug 18, 2011
Find here the extraction of the configuration and the debug sysout. The radius servers works fine with all the other accesss like ssh, telnet...
Just the http access fail. This configuration work fine with the version 12.2.55 installed before.
Aaa new-model
aaa authentication login default group radius local
aaa authentication login physique local
[Code].....
View 2 Replies
View Related
Apr 25, 2011
I am running ASA version 8.4(1), and anyconnect version 3.0.1047. My SSL VPN works fine, but i run into an issue with one user . his account did not work , and everytime users logged in it got this message "VPN Server could not parse request".
I found the problem after getting a user information meaning his username and password. His password had "&" as one of the special characters. when we change it to something that does not have that , it works just fine.
We are using microsoft NPS server as radius. but when i run a test within CLI it works just fine, only when anyconnect asks to authenticate it fails.
View 5 Replies
View Related
Aug 6, 2012
Any software to measure Authentication time between client and Radius serverr.
View 8 Replies
View Related
Nov 22, 2011
I have been trying to get our IPS (ASA-SSM-10 and 4260) to authenticate with Cisco Radius ACS 5.2 and they are not working. However, I was able to get them working with Microsoft Radius. Below is the logs from the IPS:
evStatus: eventId=1321566464942057375 vendor=Cisco originator: hostId: NACAIRVIDLAB1 appName: authentication appInstanceId: 350 time: 2011/11/23 17:50:38 2011/11/23 09:50:38 GMT-08:00 controlTransaction:
[Code].....
View 0 Replies
View Related
Nov 14, 2011
I'm running WCS 7.0.220.0.I would like to authenticate users that are able to logon the WCS, through MS Network Policy Service (RADIUS).I would like all my domain users to be member of the local group on the WCS "Lobby Ambassador", so all domain users has access to generate guest access accounts, for the web auth... I can see under the WCS Administration under AAA that it should be able to use RADIUS - but i'm not sure how to setup the NPS policy?
View 1 Replies
View Related
Mar 10, 2011
I have a questión about radius authenticaction with AD, when I log in into the network with user in AD and I make a mistake in password my radius authenticaction event in ACS 5.2 dont show me this logg. only show the authentication succeeded but dont show me the authentication failed. Maybe i must to enable same service to show the authentiaction failed. The Voice authetication works fine..
This is the confg in the port of the switch:
interface FastEthernet0/12 switchport mode access switchport access vlan 2 switchport voice vlan 10 authentication port-control auto authentication host-mode multi-domain authentication violation protect authentication event fail action authorize vlan 11 authentication event fail retry 2 action authorize vlan 11 authentication event no-response action authorize vlan 11 authentication periodic authentication timer reauthenticate 60 mab dot1x pae authenticator dot1x timeout tx-period 10 dot1x max-reauth-req 3 spanning-tree portfast end
Vlan 2: DATA
Vlan 10: VOICE
Vlan 11: GUEST
View 1 Replies
View Related
Jan 3, 2013
I am configuring an old WLC4400 with V4.2.130.0. I added a new sub-interface for VLAN 50 with proper IP for the subnet and then add the Radius server(Windows server 2008 with NPS) onto WLC4400. I then created new WLAN with WPA+WPA2 Encryption and 802.1x key management and selected the Radius server under AAA for authentication.
Configured the test XP with WPA-Enterprise and PEAP as EAP method. I purposely configured computer to prompt for username and password.
When I try to connect, I did get prompt for username and password. However after that nothing happens. It seems like laptop just keep trying to authenticate.
I checked windows event log and do not see anything under NPS. I know this windows server NPS setup works as it is also the authentication server for our remotevpn.
is there any special option I need to turn on for WLC in order for Radius authentication work? Or is there any known bug with V4.2.130.
View 13 Replies
View Related
Aug 11, 2011
I'm in the process of moving some of our remote access vpn to an asa5520 and anyconnect.
The problem I've come across is that when using radius as authentication, I choose any one of my connection profiles in anyconnect and log in with any username regardless of the group on radius.
How do I map the connection profile to a group on radius so that i can separate the users?
View 1 Replies
View Related
May 17, 2011
I have a 5510 authenticating successfully with a RADIUS server. I'm using it for VPN authentication and it works great. I would also like to do this for administrator access to the ASA. When I turn it on though, any authentication for VPN access is also granted administrative access to the ASA. Obviously, I need to limit that to a select few users.
View 1 Replies
View Related
Sep 2, 2012
which is the best RADIUS server for 802.1x wired authentication?
View 1 Replies
View Related
May 24, 2011
I am trying to authenticate on Juniper NSM express using cisco ACS 5.2. The request is arriving at the cisco ACS but i am getting the following error.RADIUS requests can only be processed by Access Services that are of type Network Access.
View 4 Replies
View Related
Jan 9, 2012
I am having ACS 4.0.2 in my network, which I want to use for 802.1x Radius Authentication for Clients on PEAP-MSCHAPv2 methodology.As per the documentation " EAP Authentication with RADIUS Server", Doc ID: 44844.I have configured Network Configuration and populated AAA client IP range and Secret Key.
Question1: Under Authenticate Using option, there are various RADIUS flavors available for selection. For a Non Cisco AAA client, should I select RADIUS IETF?
Question 2: In the above snap shot, It has an option called Global Authentication Setup, where we can setup EAP configuration. Under PEAP subsection there is an option to "Allow EAP-MSCHAPv2" check box.After checking that, is a restart required to the ACS Server? Would it cause any disruptions to the existing services on the ACS?
View 3 Replies
View Related
Nov 6, 2011
I am trying to setup a RV042 for a Client VPN using AD / Radius authentication. When it was purchased I saw radiuslisted as a feature on it, but I'm not seeing a way to set this up.
[URL]
I have upgraded to the latest firrmware, I have a VPN working with accounts on the router that I manually create, but am not seeing anyplace to configure radius.
View 5 Replies
View Related
Apr 8, 2013
I have a 5508 controller running 7.4.100 and have a WLAN where I have radius configured. On my controller the client machine I'm using appears but the radius authentication doesn't appear to be working. Is there anything on the controller I can do to verify that the request is even being sent to my Microsoft IAS server? The log on the server doesn't show any requests from the controller so my early days guess is the controller isn't actually sending it.
View 3 Replies
View Related
Jul 4, 2012
how to setup ACS 5.3 to authenticate wireless users over radius? I currently have the SSID pointing to a Microsoft IAS server and would like to move the authentication to be done via ACS.
View 1 Replies
View Related
Mar 6, 2013
Can the 2504 WLC be configured to work with one RADIUS Server for Authentication of Management Users and with a second server for 802.1x EAP-TLS certificate authentication for the end users.
Management Users will authenticate on RADIUS Server 1.Wireless End users will request 802.1x EAP-TLS authentication certificate from AAA server 2.
View 5 Replies
View Related
Jan 19, 2012
I have configured a Cisco 877 router to send RADIUS requests when a user logs in to the console (Line Console or Line VTY) using the following config:
aaa new-model
aaa authentication login default group radius
aaa authentication ppp default group radius
radius-server host 10.0.0.1 auth-port 1812 acct-port 1812 key mysharedkey
When I log the RADIUS packets I see that the Cisco router is sending the initial AccessRequest using PAP.
How can I configure the router to send it's inial AccessRequest packet using CHAP?
View 5 Replies
View Related
May 6, 2013
I'm a trainee in Network and Telecommunication, and I have to do a "model" with a controller, an AP, and a RADIUS server. Communication and configuration of the lightweight AP has been done.
I use an autonomous access point 1220 as the RADIUS server (no considering it as an AP), and I'm a beginner in RADIUS configuration. I get a "Processing AAA Error 'No Server' (-7) for mobile 00:24:d6:8f:2c:7e" when I launch a debug targetting my PC, connecting to the LAP.
Precursory : 10.137.125.71 is the IP address of the ap1220, working as the RADIUS server 10.137.125.15 is the IP address of the controller. 00:24:d6:8f:2c:7e is the MAC address of my PC, connecting to the Wi-Fi. ping works to the RADIUS, to the controller. Each devices are connected by a layer 3 Switch, and ping each others. The Wi-Fi works when I don't use 802.1X (or when I don't use RADIUS authentication at all)
What I did on the RADIUS server (ap1220 autonomous) :
aaa new-model
radius-server local
nas 10.137.125.15 key password
[Code]......
View 5 Replies
View Related
Oct 31, 2010
For some reason, i can't get the lobby "sponsors" to authentication to the Guest NAC server (2.0.2) using ACS 5.2 via Radius.I was able to figure out how to get the Guest NAC Radius Authentication for "Administrator" to work by adding custom Radius value IEFT-6 under...
Policy ElementsAuthorization & permissionsNetwork AccessAuthorization Profiles
I added a policy & under the Radius Attributes Tab... I manually entered an Attribute that looks like the following:
Dictionary Type: = RADIUS-IETFRadius Attribute: = Service-TypeAttribute Type: = EnumerationAttribute Value: = StaticValue = "Administrative"
I then created an Access Policy... I looked for a specific AD group - Result = "Name of Custom Policy Above"...
All of that is working just fine.... the NAC Guest Docs tell you the Radius server must return a value of IETF-6...
When it gets into the Sponsor section, it doesn't tell you the value your Radius server should return... so just for grins, instead of "Name of Custom Policy Above", I tried "Permit Access"... i tried the "Name of Custom Policy above"... Not sure what else to try to get this to work...
here is a like to the document i'm following: URL
Page 68 refers to the "Configuring Sponsor Authentication" for Radius.. it just tell you to add the Radius Server & change the authentication order.
View 9 Replies
View Related
Oct 12, 2011
We use LAP 1042's as our main AP's, and we set those in H-REAP (with Local Switching) in order to let them work properly. This is because our WLC is not located in the AP's local network. This is something that, sadly, cannot change, so this has to stay the way it is now.We also use a freeradius server to authenticate users on our wireless network. In our previous situation, before using Cisco appliances, we would just set our web auth page to a certain URL and make sure that the URL was granted access before authentication. We obviously found out that Cisco implemented this by using a Pre-Auth ACL. As a result we've added the IP adres of that web login page to a ACL and added that ACL to the pre-auth for the WLAN that will use Radius Web Auth. The WLAN also has the Radius servers added to the AAA page, so those are in place.
Now comes the problem though. When I connect to the WLAN that will have to use Radius, and try to open a page it will start trying to load the virtual interface (1.1.1.1) and then it will try to redirect to the web-page that I defined in the External Server. Like I stated, I've added the webpage's IP adres (after resolving it) to the pre-Auth ACL, and when I look at the counters I see that go up every time I try to load a page. Yet the browser on the computer gives me a time-out trying to load the external web-server web auth page.
When I disable Web-Auth all-together, I get internet straight away, so the problem obviously is located in the web-auth settings or ACL settings somewhere, but at this point I just don't know where to look anymore.
View 6 Replies
View Related
Dec 22, 2012
Using Cisco ASA I want the ssl clientless vpn users to be authenticated through a local Radius-Server. but it does not work, and on asa while i want to see (Debug Radius) output, there is no debuging msgs displayed. When i try to test the user which i have created on the ACS-Server 4.2, the test gets successful. where i have made a mistake in my configuration ?
View 2 Replies
View Related
Nov 26, 2011
I want to secure my routers & switches using ACS server (win server 2003 platform)i prefer Radius how to set it up lets say my ACS server ip addy 192.168.100.100 & key cisco both how to set up ACS for the router/switch & commands for router/switch ALSO, i wanna keep open a back door. if some ACS server is down, i want, ppl can log into router/switch using SSH (local user/pass) but only when ACS is down?
View 4 Replies
View Related
Mar 13, 2012
I have this scenario, AS5510 ver 8.4(3), VPN Client 5.0.07, RADIUS authentication with IAS on Windows 2003 Server.The issue is that, establishing the connection with the VPN Client, if the user credentials are correct every things works fine, but if we introduce a wrong password I don't receive an error message or a again the authentication form.Nothing happens the VPN Client keep trying to "contact security gateway", after about 5 minutes it stops without any message.Debugging the authentication process in the ASA I see that if the password is incorrect the radius authentication response is "reject". I have also tried with a different version of VPN Client but nothing change.Using AnyConnect client every things works fine.
View 1 Replies
View Related
Mar 28, 2012
I try to setup a 1141 aironet AP to authenticate my user through our Ms Radius Server ( Win 2008 R2).Everything is fine with small Bussiness AP WAP4410N with the following configuration:But I can't setup successfully the aironet 1141 with the same settings and getting it works.Here is my configuration for the Aironet 1141 Vlan 1 is the ssid I want to get it work with Radius.
View 1 Replies
View Related
May 20, 2013
I have a aeronet 1250 access point and i have a windows 2003 radius server configured to authenticate users. I need to configure the access point for radius authentication .
View 1 Replies
View Related
Mar 24, 2013
i am trying to assign a right role for a user who authenticates to nexus 7k switch via radius. i am using cisco ISE version 1.1.1.268 and the nexus version is 5.0.2,I have created a role on nexus.
View 1 Replies
View Related
Feb 19, 2012
RADIUS authentication SF300-24P
We have just purchased 20x SF300-24P switches to be installed at our remote offices and we are unable to get RADIUS authentication to work. We already use RADIUS on all our primary network CISCO switches (e.g. 4506s¸ 3560s, 3750s, AP1231Gs,etc) and these work fine so we know the RADIUS server is working.
We are trying to use RADIUS authentication to gain management access onto these switches. Quite simply although we can see that the RADIUS server is accepting the username and password being sent, however the switch says “authentication failed” when to receives the response. We are using Microsoft NPS RADIUS Clients for authentication purposes.
We have upgrade the switches to the latest firmware 1.1.2.0, via the console it seems to have a very cut down IOS version so we cannot use the typical CISCO command set to configure the RADIUS as we normally would. Looking at the web GUI there seems to be a number of options missing including the Accounting port. When debugging is switch on there is no indication to say that any of the settings have been misconfigured.
View 33 Replies
View Related
Mar 13, 2012
I have setup my radius server access on the Nexus but am unable to authenticate through putty. If I do a radius-server test on the Nexus it says I authenticate. Here is the log I am getting.
2012 Mar 14 16:03:21 switch-a %AUTHPRIV-4-SYSTEM_MSG: pam_unix(aaa:auth): check
pass; user unknown - aaad
[Code].....
View 1 Replies
View Related
Sep 3, 2011
I have a Cisco C1140 Ap. I have cnfigured the device. Initially for testing i used WPA and authenticated locally. I have now setup a radius server and added my AP in as a client etc. I have changed my SSID's to authenticate with the radius server and i am having issues authenticating.I can connect via a PC and an iphone. They say that i am connected but i get no ip address and the debugs.
View 1 Replies
View Related
Mar 19, 2012
I am trying to get AAA authentication for HTTP to use radius, and seem to be having problems with setting the priviledge level. It works fine with SSH login, but doesn't work with web management. The model is a WS-CBS3130X-S-F running 12.2(58)SE1 with http version 1.001.002...
Config is as follows:
aaa new-model
aaa authentication login VTYSandHTTP group radius local
aaa authorization exec VTYSandHTTP group radius local
ip http server
ip http authentication aaa login-authentication VTYSandHTTP
[code]...
This is what I get when I try to log on to HTTP
HTTP AAA Login-Authentication List name: VTYSandHTTP
HTTP AAA Login-Authentication List name: VTYSandHTTP
HTTP: Authentication failed for level 15
View 3 Replies
View Related
Mar 18, 2013
I'm working on a project where a wi-fi client is tracked and located using RADIUS authentication requests. The problem I'm running into is that the WLC (5508) sends an RADIUS authentication request to my freeradiusd, which is ok so far, but if the client roams to another accesspoint (3602AG, 1131AG, 1252AG), the WLC does not send a further RADIUS auth. request - and the client is allowed to connect to the next ap.Is there an option like RADIUS-cache which I can disable, so that the WLC sends everytime an authentication request when a client tries to connect to an ap or roams from one ap to another one?
View 4 Replies
View Related
Jun 20, 2012
I configured the 2504 with 2 SSIDs for staffs and guests.I also configured the Lobby admin with web auth. But if a guest wants to connect our wireless he/she has to enter the PSK key and then only they are able to connect with the user id and password given by Lobby admin. Can we avoid this key and let the guests connect straightaway with the web auth?I’m planning to configure 802.1x & Radius dual authentication for staffs SSID..
View 5 Replies
View Related
