I am trying configure tacacs authentication for http in Cisco 2960 with IOS 15.0.1.SE. [code] But the device is not authenticating. It ask the credentials (user and pass) but not authenticates.
View 7 RepliesMy switches are able to successfully authenticate user access against ACS 5.1 via SSH with TACACS+, but I am not able to authenticate via HTTPS with TACACS+. I don't even get a log in ACS when attempting to authenticate via HTTPS.
Here is my AAA config, followed by a debug:
aaa new-modelaaa authentication login ACCESS group tacacs+ localaaa authorization consoleaaa authorization config-commandsaaa authorization exec ACCESS group tacacs+ aaa authorization commands 1 Priv1 group tacacs+ none
[Code]......
All ip's and any identifying numbers have been change to protect.
I have a 6500 series switch that for some reason will not authenticate to the tacacs server. When you try, you get a password authentication failure. However, it will let you use the configured username and secret to log in thru ssh. And the enable secret to get into privileged mode. Tacacs key is correct, btw.we will call the server vlan 300 and the admin vlan 400.the tacacs source interface is in vlan 400 and the tacacs server is in vlan 300.
I can ping the tacacs server via the switch, but when i use the source cmd with the ip address of the admin interface vlan, ping will not work. I changed the tactics source interface to vlan 300 (the server vlan) and authentication with the tacacs server works fine. ip routing is turned on. There are entries for both the server vlan subnet and the ad-min vlan subnet in the routing table. There are only standard access-lists, and none of them are blocking packets from getting to the tacacs server via the admin vlan.
I could just leave the source interface on the int vlan for the servers, but I would like to find out why this isn't working. I have 1 other 6500 switch on a different network that is configured exactly the same (except for ip's, keys, and vlans) and am not having any issues with that LAN. I also have 6 other 3700 switches on the network that Im having an issue with, and none of them are having issues with authentication.
Find here the extraction of the configuration and the debug sysout. The radius servers works fine with all the other accesss like ssh, telnet...
Just the http access fail. This configuration work fine with the version 12.2.55 installed before.
Aaa new-model
aaa authentication login default group radius local
aaa authentication login physique local
[Code].....
how do i configure user authentication via TACACS on UCS 1.4 with ACS 5.2? My TACACs connection works, and my user authentication is successful, but i can only get read-only rights. I have tried several versions of "cisco-av-pair= role=admin" both as mandatory attributes named role and as cisco-av-pair=role , with "admin" as the value, and i still get read-only.
When i attempt to find any documentation, it only describes ACS 4.2, which is another problem i have with most documentation for new cisco products (i have this exact issue with my NAMs, nothing i do to change the attributes results in successfully logging into the NAM, and all config guides are written in 4.2 speak).
is there any possiblity cisco is going to release some documentation on how to convert 4.2 speak to 5.2 speak?
I want to configure managment-access authentication to the WCS via tacacs+. The AAA Server is Cisco ACS 5.2.I made it and it works, but only with PAP Authentication Type. Chap doesn't work 4 me.The Access Service is configured with allowed protocols PAP and CHAP.The ACS Monitor just display an error with these steps:Received TACACS+ Authentication START Request
View 1 Replies View RelatedIs there a decent guide on how to configure ACS5.2 for TACACS management authentication of WCS?
View 2 Replies View RelatedI am working for an Air Force client and am adding a handful of 5548s into their network. My question is how Tacacs+ is configured. My hands are tied in regards to testing in an operational environment so I want to ensure the configs are correct prior to deployment/maintenance window and avoid any remote issues.
I have read the "Cisco Press - TACACS+" config guide and it was somewhat vague in regards to operational deployment.
My basic NX-OS configs are as follows:
- feature tacacs+- tacacs-server key 7 "002A52xxxxxxxxxxxxxxxx8"- tacacs-server host 128.xx.xx.xx timeout 10- tacacs-server host 128.xx.xx.xx timeout 10- tacacs-server directed-request
When I try to set the following command string, aaa authentication login default group tacacs+ local, the NX-OS asks me the input a "server group name". There are no server groups configured. Do I need them? Can I get by without configuring a group name because the client probably will not.
The Cisco IOS devices are configured with normal aaa authentication/authorization parameters. Also, do the VTY ports default to sshv2 and the correct tacacs+ parameters with the "transport input ssh" command (not available)?
I have configured ssh on a 2960 to use public key authentication. Now that I can securely log into ssh without a password Is it possible to disable password authentication so that it is impossible to login without the key?
View 2 Replies View RelatedI am seeing the following behavior when computers move from one switch to another with dot1x ONLY when there is a 'stupid' switch in between.
computer -------- 'stupid' switch ------- 2960
dot1x is working fine but when the computer is disconnected, the port still shows the authentication session id so when the computer connects to another port or switch, authentication succeeds but traffic doesn't pass. While I'm almost certain that the culprit is the 'stupid' switch that doesn't clear the session id, I have already tried another one and the problem remains so I'm actually just asking for a confirmation that all these 'stupid' switches present this behavior and if there is a workaround in this case.
I am trying to get to work Web-based authentication on Catalyst 2960 and 3560 for clients that don't support dot1x. I followed this guide. Here's the problem: Client (win7) joins the network, opens the web browser and tries to navigate to any http site. The switch forces him the "login" page in which he has to enter credentials. After the client enters credentials, the switch sends http 500 internal server error page and nothing happens. Doesn't matter if the credentials were correct or not. Also i checked radius logs for requests, the switch doesn't even ask radius.
The configuration:
sh ip admission configuration
Authentication Proxy Banner not configured
Consent Banner is not configured
[Code].....
I have CISCO 2960 switch at my LAN. How to configure its IP address from console or hyper terminal ?
View 11 Replies View RelatedI am trying to configure a new 2960 POE switch, but seem to me the int fa0 is layer 3 interface. Is any way we can convert it to a switchport, so we can connect it to other switch in trunk mode?
View 1 Replies View RelatedWill catalyst2960 supports SSH, and how to configures with CLI.
View 2 Replies View RelatedThis is probably a dumb question, but I have read the 2960 stack administration guide and it does not explain how to configure the stack IP address. It says several times that the stack can be managed from the stack IP address, and that the stack IP address is a system-level configuration item. But it never explains how to configure the stack IP address.
View 3 Replies View RelatedToday in my rush to get home I plugged in a new 2960 stack and did a little bit of very basic configuration, but no passwords were set. I tried to telnet in and the message says that a password is required, but none is set. I tried the SDM as I hadn't turned it off yet and it is prompting me for a user/pass but I have no idea what to put in there. No console is available, it's a new office so no employees around either.
View 14 Replies View Relatedconfiguring a working route between two subnets (172.28.0.0/16 and 192.168.0.0/24) on a Cisco Catalyst 2960-S.
Problem: The subnet 172.28.0.0/16 is on VLAN 40 and the clients on this subnet have to access a preconfigured device with an ip in 192.168.0.0/24 subnet. The configuration of this device cannot be changed.
I have an Cisco 2960-S Lan Base (c2960s-universalk9-tar.150-1.SE3) switch [URL] that I would like to use to solve this problem.
I have 2960 cisco switch. I want to configure private vlan. But it is not getting configured in cisco 2960. Is there any other way to configure that in switch.
View 1 Replies View RelatedI'm about to configure radius on a 2960 and 2955 switch as I have been testing this on a 1841 router and to my dismay I can't see the options to configure radius, do these L2 switches not supoprt radius?
edit - apoligies I forgot the "aaa new-model" all ok now
Although when I added:
radius-server host 10.1.1.1 auth-port 1645 acct-port 1646 key 123456789
radius-server host 10.1.1.2 auth-port 1645 acct-port 1646 key 123456789
radius-server vsa send accountingradius-server vsa send authentication
I got this:
Warning: This CLI will be deprecated soon. Please move to radius server <name> CLI.
And what woudl the above look like if I configured it that way?
I'm trying to configure an 1142N AP + 2960-S + ASA5505 with wireless, vlans and trunking with no success. DHCP is provided from my DHCP-server on the inside.
View 4 Replies View RelatedI want to configure IEEE 802.1x port-based authentication on cisco switches, preferable 2960 series. Which models support this feature?. I have try with some older switches but it doesn't works properly on everyone. I have upgraded them whitout better results, there is namely an issue with TLS handshaking on some switches which produces authentication to fail.
View 1 Replies View RelatedI Have a problem I'm trying to configure automatically my switch over ther DHCP when I start the switch it request an IP from the DHCP from here everythings is fine but it does nothing more,indeed I put on my dhcp the option 66 and 67 which is an adress of my TFTP server and a file to download and the switch seems not to understand theses options , I tried my dhcp with a cisco airport and everythings works fine the File from the TFTP is automatically downloaded into the airport...There is an option to add or am I missing something in order to make it work with my switch ?
My switch : Catalyst 2960IOS VER : 12.2(55)SE5
As per the attached diagram: How do I configure the 2 ports on the 3560 (Ports 6 & 7) and the connected ports on each of the 2960 switches (Port 25) to provide redundancy.
If the up link from Switch A dies then I need the traffic to flow through the trunk and utilize the up link on Switch B with minimal delay (milliseconds).
I need to configure a Cisco 2960 switch as a DHCP server. The current IP address will be on a different seed than the DHCP addresses. i.e.
Switch IP = 10.1.2.3, GW = 10.1.2.1, Subnet = 255.255.255.0
DHCP addresses would be 192.168.1.1 - 200, GW=???? (10.1.2.3?) and subnet would be 255.255.255.0
I am trying to configure 802.1x RADIUS Authentication on cisco 2950-24TT-L Switch. I am using following set of command as given below
Switch# configure t
Switch(config)# aaa new-model
Switch(config)# aaa authentication dotx default group redius
Switch(config)# dot1x system-auth-control
Switch(config)# inter fasteth 0/1
Switch(config)#dot1x port-control atuo
I am facing problem dot1x command is not working on interface.
I configure 3750 stack switch as core and 2960 stack switches as access layer switches.I connected my laptop to one of my core stack in VLAN 10 and I am pinging to one of my server in VLAN 1. What will be the minimum latency at the time of inter VALN routing
View 2 Replies View RelatedI have a Cisco ASA (8.2) setup with remote access for my users using Cisco VPN client. The authentication is passed off to my ACS 5.3 which then checks with AD. What I've done so far is create Access Policy rule where I define specifically the Location and NDG where the ASA is and then a DenyAllCommands command set. This should pass authentications just fine but this also gives those users the ability to remote connect directly into the ASA and login successfully. Even though there is a Deny Commands there I still would prefer they get Access Denied as a message. If I do a Deny Access on the ShellProfile then this stops the login authentication altogether.
View 2 Replies View RelatedHow to be able to locate a sample, working configuration of tacacs+ authentication on the ASA5510?
View 2 Replies View RelatedI tried to configure TACACS+ authentication / authorization for NCS via ACS 4.2. For that I followed the configuration guide:
1. Configured the service for NCS with HTTP (see attachment)
2. Added the tasks to the user (see attachment)
When I try to login on the NCS it fails, in the logs on the NCS I see the following lines:
09/14/11 16:53:03.333 TRACE [system] [http-443-7] [TACACS+ AAAModule] Creating authorization socket - To Server: 192.168.49.14 - For User: netadmin
09/14/11 16:53:03.335 TRACE [system] [http-443-7] [TACACS+ AAAModule] Sending authorization request packet - To Server: 192.168.49.14 - For User: netadmin
09/14/11 16:53:03.336 TRACE [system] [http-443-7] [TACACS+ AAAModule] Receiving authorization response packet - From Server: 192.168.49.14 - For User: netadmin
[code].....
I'm trying to get user authentication backed off to ACS 5.1, I've got it working but not the way I'd like. This is using the TACACS settings not ACS mode.I've created a local user in CW and assigned it to the correct roles, then created a user in ACS with the same name and a different password and this works fine.My question is can I set the roles on the TACACS server using a shell profile/custom attributes. All the documentation I can find is for ACS v4?
View 15 Replies View RelatedI want to setup two factor authentication via ACS 5.2 TACACS+ without having to use a token (such as that by RSA). Is there a way to do it?
More info:
Users from unconnected AD domains will be connecting to the routers and switches.There is a certificate server available to generate certificates.SSHv2 is the current login protocol.
I am trying to access an ASA 5545 using TACACS+. I have the ASA configured as follows:
aaa-server tacacs+ protocol tacacs+
aaa-server tacacs+ (inside) host 10.x.x.x
[code]....
I have added the ASA in ACS with the correct IP and the correct key. When I try to test the authentication via test aaa-server authentication tacacs+ host 10.x.x.x username Cisco password Cisco, I get:
ERROR: Authentication Server not responding: No error.
I have ACS 5.2 and JUNOS 10.6.x I setup 2 classes eng-class and ops-class with read/write and read-only permission here is my configuration on JUNOS
set system login class eng-class idle-timeout 15
set system login class eng-class permissions all
set system login user engineer full-name “Regional-Engineering”
set system login user engineer uid 2001
set system login user engineer class eng-class
set system login user engineer authentication plain-text-password xxxxxxx
[code]....
I have 2 separate Authorization policies for engineer and operator group.Result,
1. engineering group is working fine.
2. the operator group its not working im unable to login to device under this group "authentication failed" but on the ACS logs its successfully authenticated.
3. Web authentication is not also working for bot group.