Cisco AAA/Identity/Nac :: How To Configure User Authentication Via TACACS On UCS 1.4 With ACS 5.2
Aug 18, 2011
how do i configure user authentication via TACACS on UCS 1.4 with ACS 5.2? My TACACs connection works, and my user authentication is successful, but i can only get read-only rights. I have tried several versions of "cisco-av-pair= role=admin" both as mandatory attributes named role and as cisco-av-pair=role , with "admin" as the value, and i still get read-only.
When i attempt to find any documentation, it only describes ACS 4.2, which is another problem i have with most documentation for new cisco products (i have this exact issue with my NAMs, nothing i do to change the attributes results in successfully logging into the NAM, and all config guides are written in 4.2 speak).
is there any possiblity cisco is going to release some documentation on how to convert 4.2 speak to 5.2 speak?
View 8 Replies
ADVERTISEMENT
Jul 18, 2011
I have some queries regarding on the report generation for on Cisco ACS v5.2.
1) Can we schedule to run a customized report on ACS and then email the report to the user?
2) Can we run a users authentication trend report based on the AD directory group rather than individual user.
3) Can we configure user authentication logs to be viewed on WCS.
View 6 Replies
View Related
Mar 4, 2012
I have a Cisco ASA (8.2) setup with remote access for my users using Cisco VPN client. The authentication is passed off to my ACS 5.3 which then checks with AD. What I've done so far is create Access Policy rule where I define specifically the Location and NDG where the ASA is and then a DenyAllCommands command set. This should pass authentications just fine but this also gives those users the ability to remote connect directly into the ASA and login successfully. Even though there is a Deny Commands there I still would prefer they get Access Denied as a message. If I do a Deny Access on the ShellProfile then this stops the login authentication altogether.
View 2 Replies
View Related
Sep 13, 2011
I tried to configure TACACS+ authentication / authorization for NCS via ACS 4.2. For that I followed the configuration guide:
1. Configured the service for NCS with HTTP (see attachment)
2. Added the tasks to the user (see attachment)
When I try to login on the NCS it fails, in the logs on the NCS I see the following lines:
09/14/11 16:53:03.333 TRACE [system] [http-443-7] [TACACS+ AAAModule] Creating authorization socket - To Server: 192.168.49.14 - For User: netadmin
09/14/11 16:53:03.335 TRACE [system] [http-443-7] [TACACS+ AAAModule] Sending authorization request packet - To Server: 192.168.49.14 - For User: netadmin
09/14/11 16:53:03.336 TRACE [system] [http-443-7] [TACACS+ AAAModule] Receiving authorization response packet - From Server: 192.168.49.14 - For User: netadmin
[code].....
View 7 Replies
View Related
May 1, 2013
I want to setup two factor authentication via ACS 5.2 TACACS+ without having to use a token (such as that by RSA). Is there a way to do it?
More info:
Users from unconnected AD domains will be connecting to the routers and switches.There is a certificate server available to generate certificates.SSHv2 is the current login protocol.
View 5 Replies
View Related
May 14, 2013
I am trying to access an ASA 5545 using TACACS+. I have the ASA configured as follows:
aaa-server tacacs+ protocol tacacs+
aaa-server tacacs+ (inside) host 10.x.x.x
[code]....
I have added the ASA in ACS with the correct IP and the correct key. When I try to test the authentication via test aaa-server authentication tacacs+ host 10.x.x.x username Cisco password Cisco, I get:
ERROR: Authentication Server not responding: No error.
View 20 Replies
View Related
Jul 12, 2012
I want to configure managment-access authentication to the WCS via tacacs+. The AAA Server is Cisco ACS 5.2.I made it and it works, but only with PAP Authentication Type. Chap doesn't work 4 me.The Access Service is configured with allowed protocols PAP and CHAP.The ACS Monitor just display an error with these steps:Received TACACS+ Authentication START Request
View 1 Replies
View Related
Aug 6, 2012
I have ACS 5.2 and JUNOS 10.6.x I setup 2 classes eng-class and ops-class with read/write and read-only permission here is my configuration on JUNOS
set system login class eng-class idle-timeout 15
set system login class eng-class permissions all
set system login user engineer full-name “Regional-Engineering”
set system login user engineer uid 2001
set system login user engineer class eng-class
set system login user engineer authentication plain-text-password xxxxxxx
[code]....
I have 2 separate Authorization policies for engineer and operator group.Result,
1. engineering group is working fine.
2. the operator group its not working im unable to login to device under this group "authentication failed" but on the ACS logs its successfully authenticated.
3. Web authentication is not also working for bot group.
View 14 Replies
View Related
Jun 27, 2012
we have a ACS server V4 installed on W2003 server ,when we make a telnet to an equipement on the wan the authentication pass on the first connexion ,but when we telent to a switch on the lan the first connxion fails and we need to retry to login .when i check the field attempt log on the ACS i dont find the field attempt.i find this issue in ALL switch on the LAN ,from the switch i can ping the the ACS server .this problem appear frequently?
View 1 Replies
View Related
Dec 20, 2009
Having an issue with authenticating Juniper J Series and SRX devices with ACS 5.1 The devices can authenticate using TACACS to ACS 5.1 via the CLI (telnet / ssh connections) but cannot using the JWEB management page.Doing packet captures between the Juniper devices and the ACS 5.1 box shows the Authenticate phase passing, but it does not progress onto the Authorisation phase. There is nothing of interest in the ACS Logs (Even with the debugging levels turned right up) The same Access service is in use for both the CLI and GUI (JWEB).Using ACS 4.1, both CLI and JWEB authentication works.[URL]I'm thinking the issue is with ACS 5.0 / 5.1 and it maybe not liking the response from the Juniper (even though it should be the same mechanism)
View 6 Replies
View Related
Feb 2, 2013
I am trying to configure ACS 5.2 to do all authentication against Microsoft AD, but use local identity groups to determine TACACS+ authorization.
View 1 Replies
View Related
Aug 22, 2009
We added AAA client in the Cisco ACS 5.0 for WLC 4402 (TACACS+ Authentication) and configured WLC 4402 to use TACACS+ authentication for the management access. We can't get this work for some reasons.
Other Cisco routers and switches all worked fine with TACACS+ authentication. This is a TACACS debug output from the WLC;
Sun Aug 23 16:19:06 2009: tplus response: type=1 seq_no=2 session_id=f59bbf0b length=15 encrypted=0
Sun Aug 23 16:19:06 2009: TPLUS_AUTHEN_STATUS_GETPASS
[Code].....
View 24 Replies
View Related
Sep 12, 2011
Is there a decent guide on how to configure ACS5.2 for TACACS management authentication of WCS?
View 2 Replies
View Related
Jan 5, 2012
ACS 5.1 is failing to authenticate tacacs authentication to the ASA firewall, getting
View 6 Replies
View Related
Mar 15, 2010
I've been configured my device 6506-9 with TACACS+ server authentication: [code]
but when I tried to access the device only uses authentication local but not uses TACACs (with username/password defined) it can be an error in configuration? in the other devices of network this works properly, only it's wrong in Cat6506-E
View 6 Replies
View Related
Aug 26, 2010
My switches are able to successfully authenticate user access against ACS 5.1 via SSH with TACACS+, but I am not able to authenticate via HTTPS with TACACS+. I don't even get a log in ACS when attempting to authenticate via HTTPS.
Here is my AAA config, followed by a debug:
aaa new-modelaaa authentication login ACCESS group tacacs+ localaaa authorization consoleaaa authorization config-commandsaaa authorization exec ACCESS group tacacs+ aaa authorization commands 1 Priv1 group tacacs+ none
[Code]......
View 8 Replies
View Related
May 15, 2012
i am running NX-OS image n5000-uk9.5.1.3.N1.1.bin on the nexus 5020 platform.i have configured authorization with tacacs+ on ACS server version 5.2 with fall back to switch local database.a user test with priv 15 is craeted on ACS server, password test2 everything works fine, until i create the same username on the local database with privilege 0. ( it doesnt matter if the user in local database was created before user in ACS or after ) e.g.: username test password test1 role priv-0 (note passwords are different for users in both databases)
after i create the same user in local database with privilege 0,if i try to connect to the switch with this username test and password defined on ACS, i get only privilege 0 authorization, regardless, that ACS server is up and it should be primary way to authenticate and authorizate the user.
View 3 Replies
View Related
Oct 13, 2011
I am trying configure tacacs authentication for http in Cisco 2960 with IOS 15.0.1.SE. [code] But the device is not authenticating. It ask the credentials (user and pass) but not authenticates.
View 7 Replies
View Related
Dec 5, 2012
I successfully authenticate through ACS to my Identity Store, but only get dropped into a non-enable prompt: ciscoasa> How can I get an Authenticated user directly into enable mode?
View 3 Replies
View Related
Jun 6, 2011
I am experiencing an issue where NX-OS on our 5010s is allowing both Local AND TACACS authentication concurrently. If I don't configure any aaa authorization commands, the locally logged in user has unmitigated access to the device. Once I enable aaa authroization, all commands issued by the locally logged in user are denied by ACS, but they can still log in to the device. When I comb through the logs on the ACS server, I see successful logins when TACACS credentials are used, and also the failed attempts when the locally configured credentials are used. On the switch, however, I receive "%TACACS-3-TACACS_ERROR_MESSAGE: All servers failed to respond" when using locally configured credentials on the switch itself. We are running ACS v4.2.
View 6 Replies
View Related
Jul 25, 2011
We have a Catalyst 3750 switch that failed over to local login after the Tacacs authentication stopped working. I went through the configuration settings and everything appears to be identical to another switch in this same building.
View 4 Replies
View Related
Sep 20, 2011
I am running ACS 4.1.1.23 on a Microsoft server and I am trying to get TACACS to work with two Linux servers. The servers are capable of TACACS, are using port 49 and have the correct shared secret. I believe I do not have the devices configured properly on the ACS side. These 2 servers currently are using RADIUS and we are getting bit by the bug where the ACS application will start rejecting RADIUS authentication requests but still accept TACACS requests.
View 6 Replies
View Related
Sep 1, 2011
I am trying to setup up a rule to allow wireless access only to users in my AD when they use computers from my AD.I have Machine authentication working on it's own (computer boots up and connects to wireless - confrimed by ACS logs) I have User authentication working But when I try to creat the floowing rule:it does not work.
Access Policy
Access Service:
Default Network Access Identity Store:
AD1
Authorization Profiles:
DenyAccess
Exception Authorization Profiles:
Active Directory Domain:
[code]....
Everything seem to fine until it gets to the last rule.
View 1 Replies
View Related
Nov 12, 2012
I want to have a local user in ACS that is permitted to login to routers. I have TACACS with AD already working but cannot get a local user to work. I used to do this in ACS 4.x.I created a user in the internal identity store.I tried configuring a policy to allow this users TACACS authentication multiple ways to no avail. I cannot find a config example doc and cannot figure it out from the user guide as the documention is sorely lacking.
View 5 Replies
View Related
Sep 26, 2011
We have configured ACS 5.1 for autenticating wireless users with active directory, which is working fine now.But we would like implement that single user should be authenticated through ACS . If any user try to access WLAN from multi system will be notified with multi login access restriction.Can we implement this policy in acs, if possible what are the exact configuration changes we have to implement.
View 1 Replies
View Related
Dec 28, 2011
We have cross domain trust relationship established and I have added the user group in our ACS 5.1. we are using Active directory as an external Identity store. Also I have created a rule in the 'Access polices' to allow the user group. From the cross domain, I use abc@xxx.xyz as a user id, but I get this error message 13036 Selected Shell Profile is DenyAccess.
View 3 Replies
View Related
Jun 5, 2012
Can use ACS 5.2 as Guest user authentication server?
View 3 Replies
View Related
Apr 12, 2013
I am using ISE 1.1.3.124.My first question:I want to know the relation between the attribute "WasMachineAuthenticated" and the MAR (MAchine access restriction in advanced setting for AD).Is-it the same or not ?Once you time out, you need to do machine auth again. What is the timer ?Using the attribute "WasMachineAuthenticated", is-it the same timer that you configure in MAR ? In a distributed environnement, is the information about machine previously authenticated replicated to all policy node ?Because, if a swicth has 2 radius-server, we are not sure that it will point everytime to the same server.
View 1 Replies
View Related
Jul 18, 2011
For our wireless, we enabled the machine authentication, but we want to bind the machine authentication and user authentication together which means they need to meet both requirements to access the wireless, how can we do this? Right now looks like as soon as the machine is authenticated, it can access the network, no user authentication needed.
View 6 Replies
View Related
Jul 19, 2011
I am migrating from ACS 4.2 to 5.2. In 4.2 you could assign one user to auth via Internal Database and another user to auth via Radius Token Server. I cannot find how to do this with 5.2. There is a note in the doc that states 'Identity-related attributes are not available as conditions in a service selection policy'. Does this mean that you can only choose one auth method for all users? If it is possible to have multiple methods, how am I able to accomplish this?
View 1 Replies
View Related
Dec 17, 2011
While configuring LDAP , I got struck in “Step 3 - Directory Organization”. How to make this work? My aim is to make users authenticated from their windows domain usernames and passwords while they log in to AAA clients.
View 1 Replies
View Related
Apr 18, 2011
I have setup ACS 5.2 in my lab and have it completely funcation with Downloadable ACLs, Dynamic VLANs and the identity store on the backend is Active Directory. I need it to lock a user account in AD if there are to many auth attempts. I have gone into AD and set a max login attempts to 3 but if I continue to fail authentication (on purpose) using radius auth, it never locks out my AD account? I am using the Anyconnect 3.0 with NAM as the supplicant installed on my workstation. I have also configured the switchport that I am connect to with the following commands. I tried the dot1x max-reauth-req 3 command and that didn't really do anything for me either. What am I missing here?
switchport mode access ip access-group 10 in authentication event fail action authorize vlan 40 authentication event no-response action authorize vlan 40 authentication host-mode multi-host authentication priority dot1x mab authentication port-control auto authentication timer reauthenticate 10 authentication timer inactivity 20 authentication violation protect mab dot1x pae authenticator dot1x timeout quiet-period 5 dot1x timeout tx-period 5 dot1x max-req 3 spanning-tree portfast
View 1 Replies
View Related
Apr 28, 2011
I am trying to configure an ASA 5505 running 8.3 to allow a priv 15 local user to be able to ssh into the device and be placed into priv 15 mode without having to execute the enable command and type the enable password.Right now when you log in as a priv 15 user you still have to execute the enable command and type the enable password to get to priv 15.
View 3 Replies
View Related
