Cisco Application :: 7341 Can't See Connection Statistics In Central Manager GUI
Aug 7, 2011
I'm running v4.3.5 in our WAAS environment. At the CLI of one of our 7341 WAEs, there are several connections that show up [code] However, in the Central Manager nothing shows up - not even empty graphs - when I click on a device and go to monitor/connections statistics. After a few minutes, I do get an error message that states "Error retrieving connection stats. Please ensure that the device is online and then refresh." By the way, I get all other statics in the GUI such as Optimization Details Report, Traffic Summary Report, etc. Another thing, these WAEs are behind a router and supposedly the ports to allow access to/from the WAEs and other data is allowed through the firewall.
Is there some special port that needs to be opened on the firewall to allow for 'connection statistics' information displayed, that doesn't need to be opened for the other statistics to display? Or could this be a bug in the software?
View 1 Replies
ADVERTISEMENT
Mar 21, 2012
I'm working on a small scale Cisco WAAS deployment. I want to know if it's possible to use the entry level Cisco WAVE-294-K9 as Central Manager.Also about licensing, does this appliance model come with the enterprise level license
View 2 Replies
View Related
Mar 6, 2012
I have a little problem...I want to see the maximum tcp connections that I had on my Cisco. I tried using show ip statistics but it's not working. I have a Cisco Catalyst 3750G (WS-C3750G-48TS)
IOS -> Version 12.2(52)SE, RELEASE SOFTWARE (fc3)
View 3 Replies
View Related
Mar 28, 2013
We use Cacti to get interfaces statistics of a ASR1002 router (version 03.04.02.S.151-3.S2).A new GRE tunnel has been created, but unfortunately we are not able to get basic interface average during the day.What is surprising is the fact the graphs are built on the night only.
It seems as soon as we exceed some level of Bandwidth (~ 700-800k) the tool does not get the information.The OID I try to get are ifHCInOctets (.1.3.6.1.2.1.31.1.1.1.6) and ifHCOutOctets (.1.3.6.1.2.1.31.1.1.1.10) and some other interface statistics for both 64 and 32 bits. [code]
View 2 Replies
View Related
Aug 18, 2011
I am getting sync fail on device manger A3(2.2) to ACE 4710 appliance when I am changing certificate in one of proxy service.
View 1 Replies
View Related
Sep 6, 2011
I've got basic connectivty to our ACE30 module and when I try connecting to the management IP address (attached to the Admin context), I see a very basic GUI which only lists the CSM to ACE config conversion tool. I don't see a GUI as detailed in the document: url...How do I get the ACE Applicance Device Manager GUI working so that I can then configure real servers, serverfarms etc rather than via the GUI?Having read through copious amount of documentation I can't seem to find a refrence that would ne useful here. This should be a fairly straight forward exercise - do I need to install some other software to get the full fledged GUI working?
View 2 Replies
View Related
Nov 4, 2012
In a cluster of redundant ACE-4710, version A5(1.2), the graphical Device Manager on the primary ACE cannot authenticate users. An error message is displayed :The strange thing is that the standby ACE Device Manager work correctly. Moreover, both ACE are perfectly synchronized :
CH01AC03/P-115-A# sh ft group summary
FT Group : 14
Configured Status : in-service
Maintenance mode : MAINT_MODE_OFF
My State : FSM_FT_STATE_ACTIVE
My Config Priority : 200
[code]....
View 2 Replies
View Related
Nov 20, 2012
When trying to view the status in the Monitor tab and the Config tab after you log in to the ACE 4710 Device Manager A5 (1.2) management GUI tool, I could not retrieve the status data and the following message appeared.
"Faild to upload Adimn configuration: There is error in loading configuration: Error in loading RMO config from DB:The given index XXXXXXXXX.bak does not match table index definition"
Other features include all normal, so I can get information by using the CLI.In addition, this configuration is redundant in the Primary / Secondary, this event occurs only on the Primary.
Other:-XXXXXXXXX.bak is a backup that you created in the checkpoint, and it does not already exist.
-When I'm logged on to the GUI, the above message is displayed in the status bar always.
-It was not recovered by ACE restart it.
-When I try to create the same configuration in a different environment, it did not reproduce.
View 2 Replies
View Related
Sep 28, 2011
I have a problem in the ACE 4710. In view of the connections of a web environment. When I view connections on Config> Operations> Real Servers, Conns column values appear very high connections (Example. 1606317769078).Already in Config> Operations> Virtual Server the number of connections appear normal. Version 4710 ACE Device manger A4 (2.1a)
View 1 Replies
View Related
Nov 4, 2012
I did a clean install of windows 8 and my tooth application or drivers do not show up in device manager dell xps studio 7100.
View 1 Replies
View Related
May 12, 2012
Customer is running LMS 2.6.Scheduled backup was running perfect. But it is no more happening.When we checked we found that the "License Manager/ Deamon Manager is down" message pop ups.
We reset the casuser password, and then restarted the services. It becomes ok.But only the immediate backup is successful. Scheduled task fails for all those devices."License Manager/ Deamon Manager is down" happens quite often.
View 1 Replies
View Related
Mar 13, 2012
i have met connection problems (mainly with xp)where a laptop always have problem connecting to a secured wifi connection that has higher encryption than wep (wpa - wpa2).In general after a few tests . I am almost sure that it is xp's Wireless Zero Configuration's problem.I am wondering if there is alternatives to WZC that does not require their own brand's device to run a 3rd party Wireless Connection Manager.I am not looking for a model specific software either ,
Examples are:
toshiba connect me
tp link connection utility
intel's mobile
View 11 Replies
View Related
Sep 18, 2012
I have such input data:
2xN7K-C7010 - Nexus7000 C7010 (10 Slot) Chassis
2xN7K-M132XP-12 - 32x10Gbps
NX-OS version 6.1(1)
I have enable (by default) QoS feature on them:
N7k# show policy-map interface brief
Interface/VLAN [Status]:INP QOS OUT QOS INP QUE OUT QUE
================================================================================
port-channel1 [Active]: default-in-po default-out-p
port-channel2 [Active]: default-in-po default-out-p
port-channel10 [Active]: default-in-po default-out-p
Ethernet1/1 [Active]: default-in-po default-out-p
[code]....
View 3 Replies
View Related
Sep 27, 2011
Are there any good freeware software for network workload performance reporting (i.e. monitoring, statistics, etc. )?
View 4 Replies
View Related
Apr 15, 2012
I am interested in gathering cumulative threat-detection statistics from an ASA running 8.3, and displaying number of attacks over time. I am already capturing traffic information via netflow, but am interested in getting threat information.
Is there a way to capture the statistics via SNMP or any other method?
View 3 Replies
View Related
Apr 28, 2013
I have recently installed prime lms 1.3 and added several switches to be managed. Is there at this moment a possibility to display port statistics and network statistics for the wired part of the network? I am used working with LMS, but features like the topology view, with bandwidth usage is not yet integrated in Prime Infra it seems. Is there anything to monitor the wired network in Prime Infra 1.3.
View 2 Replies
View Related
Sep 11, 2012
when using "show mls statistics" I see a lot packets are getting L3 Processed. Does that mean they are getting software-forwarded?
IOS is 12.2(33)SXI5.
Cat6k#show mls statistics
Statistics for Earl in Module 5
L2 Forwarding Engine
[Code]....
View 1 Replies
View Related
Feb 23, 2013
how can I reset the port statitics on the RV180 router without rebooting the router? I have the latest firmware.
View 5 Replies
View Related
Sep 19, 2012
understanding of "mls qos interface stat"
I took a switch and connected it to my LAN switch is 2960 with LanBase image and PoE on it I have 3 interfaces in up state - 2 interfaces with cisco phones (6921 and 9951) nad 1 interface as uplink
here is its configuration
interface FastEthernet0/1
switchport mode access
switchport voice vlan 555
[Code].....
View 9 Replies
View Related
Mar 4, 2012
I have followed the steps in this document in detail: URL
however, my central authentication does not work. I get to the guest portal, i get authenticated through the guest portal, but then the "second" MAB authenticatino doesn't happen. In the last screencapture of the document, you get a green "Dynamic Authorization" line (third line from below). On my system this is a red line with the error message "11213 No response received from Network Access Device". (i have a successfull guest authentication in my ise logs, but it seems ise is unable to bounce or initiate the second MAB.
View 2 Replies
View Related
Oct 11, 2012
I have the Cisco EPC3825 EuroDocsis 3.0 Gateway and i cannot get statistics from this modem on snmp. Use snmpwalk. Nothing was found in settings of device.
View 1 Replies
View Related
Nov 24, 2011
Trying to change my IP address in windows 7. I downloaded Desktop Central 7.Server and Desktop Management Software: Now what am I suppose to do?
View 2 Replies
View Related
Feb 7, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : BSNL
how to get a graph of the router statistics like upload and download speeds - both total and per device? Something like MRTG. The closest I came to getting data from the router was with RouterStats-Lite, but I was unable to get it to work.
View 6 Replies
View Related
Apr 26, 2011
I am looking for a Best Practices or a few places to pay attention to in the Cisco ESW-520-48P switch I have. My VoIP solution is RingCentral, and while they are Cisco phones, I've been hestitant to setup VLANs etc. the way I am used to. Plus setting up Auto QoS seems different than what I am used to with a 3750 switch.
Right now I've left the Smartports Wizard alone, and none of the ports are configured. There are no VLANs or QoS on the LAN currently.
What I was running into were calls cutting out where one side wouldn't hear the other anymore, but the call would remain connected. However, this has happened in this small 15 person office, when there is only one employee here after hours, talking on the phone. There isn't any heavy network traffic, because I have network monitoring showing me low usage (no streaming music, videos, or anything else).
This switch has a Gb connection to a Linksys SR2024 (the server switch), which is also set at Factory Defaults. I mention that because I recently bypassed the ESW-520-48P, and plugged one phone into that switch and the RingCentral phone worked fine for outside calls.
Is there something besides QoS that I should look at in the ESW-520 switch that might be causing a checkpoint of some sort, or interrupting VoIP traffic that I need to configure or disable?
And are there any Best Practices or scenario guides for this switch? I found the Admin Guide, but it really just explains every option in the GUI for the switch. And it seems all of my CCNA training isn't working with going in and quickly troubleshooting this switch besides knowing that something in it could be hanging it up.
View 6 Replies
View Related
Jun 13, 2011
I'm planning to use this card for a 7204VXR with NPE-G1. I'll be using it for data in the customer data center; in remote sites customer has 2811 with VWIC-2MFT-E1T1, so I assume it's using a framed E1 (g704-->1984Mbps). Can I use PA-MC-8TE1+ in the central site? How will the configuration look like in the central site?
I have seen this PA is the only one available for 7204 VXR, so I assume it supports all the E1 configurations, am I right?
View 2 Replies
View Related
Mar 10, 2013
In my network:- at HO: 2 x WLC 5500 and 20AP, ACS, AD- at branches: 5 AP at each branchI configure the H-Reap. Now, I have some question about Cisco wireless:1. Only 1 Wan link between HO and branches, How I should configure when the WAN link down, all AP at branches still works, users still connect?
2.Based my network architecture, I should authentication central at HO or authentication at HO and branches? AP at branches supports local authentication or not? If we want to authenticate on AD at branches, how can I configure?3. I also want IT at branches have managed AP at their branches. When branch has visitor, IT at branch create temporary key and provide to visitor. at branch, how can I do that?
View 5 Replies
View Related
Jul 25, 2012
I have users connected to a 2960-S running 12.2(53r)SE complaining of slow network, specifically Internet performance while the upstream 2960 on the same vlan has no such issues, so I don't suspect link congestion on the face of things.I'm planning on upgrading the code, but wanted to see what could be checked first. I'm seeing some drops but could use some tips on how to proceed from here as to what might be the issue. CPU is under 10% whenever I check it.
View 7 Replies
View Related
Jun 17, 2009
how can I clear the counters of the policy-map statistics in an 7600 and the 1841 router?
View 6 Replies
View Related
Oct 16, 2012
the WLC 4404 present this logs:
*osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/927/stat.(erno 24)
*osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-TASK_GETTIME_FAILED: osapi_task.c:3431 Failed to retrieve statistics (/proc/<pid>/stats) for task 'gccp_t'
*osapiReaper: Oct 02 14:55:11.152: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/926/stat.(erno 24)(code )
when present this loggs the device present those symptoms:
lost GUI session
Lost console conection
Lost SSH and Telnet conecction
the WLC 4404 not work is stopedd
View 3 Replies
View Related
Nov 22, 2011
I have got cable modem and its output is connected to netgear router n150 wireless router model wnr1000v2.now 3 desktops and one laptop is wired to that router through 4 lan ports. now i need to access internet from all systems.and also make one system as central database so that everyone can share and use all work files.one printer is connected to one system.i also need to print docs from all systems.
View 1 Replies
View Related
Mar 10, 2013
I have an E2500 router, running the latest firmware 1.0.7.
Where or how can i see which is the machine (mac or ip) that is doing more traffic, in fact i would like to see what computers are doing how much traffic.
This is a default on most routers, its so weird to not been able to find this on a Cisco product.
View 1 Replies
View Related
Nov 1, 2012
I recently install Windows8 Enterprise build 9200 on my Dell XPS L502X and everything is working fine so far except my modem. In device manager its installed properly but the network manager doesn't list it as an option to connect to (as it usually would in win7),
View 2 Replies
View Related
Aug 20, 2011
How could i make a vpn tunnel between a router SA520 and a central UC540.
View 3 Replies
View Related
