Cisco WAN :: Clear Counters Of Policy-map Statistics In 7600 And 1841 Router?
Jun 17, 2009how can I clear the counters of the policy-map statistics in an 7600 and the 1841 router?
View 6 Replies
ADVERTISEMENT
AAA/Identity/Nac :: ACS 5.2 Command Set For Clear Counters
Sep 24, 2012I am having ACS 5.2. I have to configure a user which would have privilege 7 access and addition to this, a user can run "clear counters" command.how to configure cammand set for "clear counters"?Can i run clear counters by privilege 7?
View 2 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.1 -Allow Clear Counters Command Only
Oct 3, 2012I have ACS 5.1, I have created a user with privilege 15. I need to allow a single command by command set. I have configured command set. in command set setting i have unchecked "Permit any command that is not in the table below"
and added command as below.
Grant Command Argument
Permit clear counters
its allowing me to run clear counters, good is its not allowing to show run and configuration t commands. And problem is i can run reload command also even show interface commands.I just want to allow clear counters command only.
Cisco Application :: ACE 4710 - Allow User To Clear Counters?
Aug 31, 2011Using an ACE 4710 we have a user setup with the Network-Monitor role which allows the user to view config, interface status, etc. We would also like to allow this user to clear the interface error counters as well, but nothing else.
View 2 Replies View RelatedCisco WAN :: 3925 - Performed Clear Counters And Log Buffer Also Cleared
Jan 17, 2013I can't remember clearing the log with a clear counters. Router is a CISCO 3925-CHASSIS (revision 1.1) with C3900-SPE100/K9..System image file is "flash: c3900-universalk9-mz.SPA.150-1.M4.bin"..I did a : clear counters, enter. got this standard message >> Clear "show interface" counters on all interfaces [confirm], enter and it CLEARED the LOG BUFFER as well !!!! never seen that before. Its a newly turned up router, repurposed from another part of our network.
View 1 Replies View RelatedCisco Switching/Routing :: 7600 Load On Router Processor From Ip Policy
Jul 29, 2012today i installed new router 7600 , but im facing some thing the cpu is increasing and it reached 50 % and still increasing as the bw dissipated is increasing .im applying ip policy which set next hop for many internet source my question is , how to know the cu percentage which is used by this ip policy , also , how to know the percentage by access-list ??
View 4 Replies View RelatedCisco Firewall :: Negative Counters In ASA 5510 (show Service-policy)
Feb 7, 2012In my Cisco ASA 5510 in release 8.2, I have an extrage behavior in the output of "show service-police" command. The issue is that I create a class-map to limit trafic in one of ASA interfaces and I applied in a service policy. This is the configuration:
access-list ACL-Limitada extended permit ip host srv-proxy any
access-list ACL-Limitada extended permit ip any host srv-proxy
access-list ACL-Limitada extended permit tcp 192.168.10.0 255.255.255.0 any eq ftp-data
access-list ACL-Limitada extended permit tcp 192.168.10.0 255.255.255.0 any eq ftp
access-list ACL-Limitada extended permit tcp any 192.168.10.0 255.255.255.0 eq ftp-data
access-list ACL-Limitada extended permit tcp any 192.168.10.0 255.255.255.0 eq ftp
[code]...
Cisco :: ASR1002 SNMP Statistics For GRE Tunnel Interface Statistics
Mar 28, 2013We use Cacti to get interfaces statistics of a ASR1002 router (version 03.04.02.S.151-3.S2).A new GRE tunnel has been created, but unfortunately we are not able to get basic interface average during the day.What is surprising is the fact the graphs are built on the night only.
It seems as soon as we exceed some level of Bandwidth (~ 700-800k) the tool does not get the information.The OID I try to get are ifHCInOctets (.1.3.6.1.2.1.31.1.1.1.6) and ifHCOutOctets (.1.3.6.1.2.1.31.1.1.1.10) and some other interface statistics for both 64 and 32 bits. [code]
Cisco Switching/Routing :: 7600 Router Performance / Policy Base Routing?
Mar 6, 2012When mutiple Policy based routing configured on 7600 routers, did the router performace degraded with the number of policy based routing rules?Also, did 7600 running 12.x use per-flow based routing or per packet based routing?
View 1 Replies View RelatedCisco Switching/Routing :: 1900 - Clear DF Bit And Policy Based Routing
Jan 8, 2012I've been implementing a setup where a remote office has a Cisco 1900 router. There are 2 GRE/ IP SEC tunnels to the headquarters, 1 over public internet, 1 over a private cloud. Because of some MTU issues we have to clear the DF bit for some of the traffic, but we also want to use PBR to send https traffic over the "public internet" tunnel and the rest of the traffic over the "private cloud" tunnel. I'm able to clear the DF bit and to do the PBR with route-maps, but I'm not able to implement both functionality at the same time.
View 1 Replies View RelatedCisco WAN :: 1841 - Policy Configuration
Dec 15, 2010I have the following very simple policy configured on a Cisco 1841.
policy-map Shape-2Mb class class-default shape average 2000000 interface FastEthernet0/1[code]....
I'd just like some clarification on the best ways to monitor this. Looking at the 'sh policy-map int fa0/1' i get this:
FastEthernet0/1 Service-policy output: Shape-2Mb Class-map: class-default (match-any) [code]...
some of the sections don't make much sense to me. What is the output of that command.
Linksys Wireless Router :: E2500 / Firmware 1.0.7 - Traffic Statistics
Mar 10, 2013I have an E2500 router, running the latest firmware 1.0.7.
Where or how can i see which is the machine (mac or ip) that is doing more traffic, in fact i would like to see what computers are doing how much traffic.
This is a default on most routers, its so weird to not been able to find this on a Cisco product.
Linksys Wireless Router :: E4200 V1 Interface Counters / SNMP Support
Jun 12, 2012Any chance of one or preferably both of these before I flash the router to a more competent firmware?Rather ridiculous that there's no interface counters and no SNMP server. I prefer keeping stock firmware where possible but I need this functionality, it really isn't a big ask.That said I have an E4200 v1, which already looks like abandonware given it's been 6 months since the last firmware update - not amused and no intention of swapping a high performance router for one that sacrifices performance for better NAS functionality.
View 8 Replies View RelatedDIink DIR-655 - New Clear Modem With Another Router
Oct 17, 2012I just got ClearWire and frankly it's really good but only when wired directly to the modem. The wireless is a joke, my roommates can't even get a stable connection 20 feet away. So I was trying to hook up my DIink DIR-655 up to the WIXFPR-131 modem and it won't let me.
View 3 Replies View RelatedClear The DNS Cache On ZyXEL P-660 Router?
Apr 1, 2013How do I clear my router DNS cache on my ZyXEL P-660 router?I already cleared it on my PC with "ipconfig /flushDNS" in the command line but everyone sees my online IP camera, except me my online IP camera on LIVEwhen I try to access the camera URL i go to the router default/settings/home page
View 10 Replies View RelatedD-Link DIR-600 :: How To Clear Cache Of Router Every Now And Again
Dec 1, 2012Every 2 minutes, I want to clear it, because some machines will be turned off. Currently, they will stay on on the left hand side of my host's window explorer.
View 1 Replies View RelatedCisco WAN :: Nexus 7000 (NX-M132XP-12L) And QoS Statistics?
Sep 18, 2012I have such input data:
2xN7K-C7010 - Nexus7000 C7010 (10 Slot) Chassis
2xN7K-M132XP-12 - 32x10Gbps
NX-OS version 6.1(1)
I have enable (by default) QoS feature on them:
N7k# show policy-map interface brief
Interface/VLAN [Status]:INP QOS OUT QOS INP QUE OUT QUE
================================================================================
port-channel1 [Active]: default-in-po default-out-p
port-channel2 [Active]: default-in-po default-out-p
port-channel10 [Active]: default-in-po default-out-p
Ethernet1/1 [Active]: default-in-po default-out-p
[code]....
Cisco WAN :: X.25 And Xot On Router 7600
Dec 5, 2012The 7600 platform support x.25 and XOT features. In ios versión S764AEK9-15103SCisco 7600-RSP720 IOS ADVANCED ENTERPRISE SERVICES SSH The feature navigator display that support this features, but i'dont see these on the other newer ios version. If posible use 7600 for x.25 / xot or maybe will used de 3900 platform?
View 1 Replies View RelatedHow To Clear The Cache Of A Broadband Wireless Router
Jan 13, 2011i have a wireless-g broadband router and the cache is giving me headaches as i cannot access certain of my sites on a server in USA.
View 4 Replies View RelatedNetwork Monitoring And Statistics Software?
Sep 27, 2011Are there any good freeware software for network workload performance reporting (i.e. monitoring, statistics, etc. )?
View 4 Replies View RelatedCisco Firewall :: Monitoring Threat-detection Statistics On ASA 8.3
Apr 15, 2012I am interested in gathering cumulative threat-detection statistics from an ASA running 8.3, and displaying number of attacks over time. I am already capturing traffic information via netflow, but am interested in getting threat information.
Is there a way to capture the statistics via SNMP or any other method?
Cisco :: Network User Statistics In Prime Infra 1.3
Apr 28, 2013I have recently installed prime lms 1.3 and added several switches to be managed. Is there at this moment a possibility to display port statistics and network statistics for the wired part of the network? I am used working with LMS, but features like the topology view, with bandwidth usage is not yet integrated in Prime Infra it seems. Is there anything to monitor the wired network in Prime Infra 1.3.
View 2 Replies View RelatedCisco Switching/Routing :: MLS Statistics On Cat 6500 With Sup720
Sep 11, 2012when using "show mls statistics" I see a lot packets are getting L3 Processed. Does that mean they are getting software-forwarded?
IOS is 12.2(33)SXI5.
Cat6k#show mls statistics
Statistics for Earl in Module 5
L2 Forwarding Engine
[Code]....
Cisco Routers :: RV180 Reset Port Statistics?
Feb 23, 2013how can I reset the port statitics on the RV180 router without rebooting the router? I have the latest firmware.
View 5 Replies View RelatedCisco Switching/Routing :: QoS Statistics On 2960 With Phone
Sep 19, 2012understanding of "mls qos interface stat"
I took a switch and connected it to my LAN switch is 2960 with LanBase image and PoE on it I have 3 interfaces in up state - 2 interfaces with cisco phones (6921 and 9951) nad 1 interface as uplink
here is its configuration
interface FastEthernet0/1
switchport mode access
switchport voice vlan 555
[Code].....
Cisco Application :: 3750G - Maximum TCP Connections Statistics
Mar 6, 2012I have a little problem...I want to see the maximum tcp connections that I had on my Cisco. I tried using show ip statistics but it's not working. I have a Cisco Catalyst 3750G (WS-C3750G-48TS)
IOS -> Version 12.2(52)SE, RELEASE SOFTWARE (fc3)
Cisco WAN :: QoS On 7600 Series Router
Oct 18, 2012I am looking for the best QoS method for a 7600 series router. We have a 7604 edge router that has remote branch connections to it via GRE tunnels. unfortunately I cannot shape on these GRE tunnels neither can I use bandwidth or priority statements.
View 1 Replies View RelatedSetting Up Belkin Router Wireless With Clear Modem?
May 1, 2012I have a CLEAR modem want to know how to setup my Belkin router so I surf the internet for my laptop and tablet pc. The subsection is the router.
View 1 Replies View RelatedLinksys Wired Router :: BEFSX41 Won't Allow To Clear DNS Entries?
Feb 17, 2011I am trying to configure a BEFSX41 router which sits behind a Motorola SB 5120 cable modem. Somehow it now shows DNS entries on the basic setup page. Comcast advises me to zero out all those entries. When I make the attempt a message pops up saying the entry is invalid, and when I close the warning the entry reverts. The router is set to get its IP address automatically from the SB 5120.
View 3 Replies View RelatedCisco Application :: 7341 Can't See Connection Statistics In Central Manager GUI
Aug 7, 2011I'm running v4.3.5 in our WAAS environment. At the CLI of one of our 7341 WAEs, there are several connections that show up [code] However, in the Central Manager nothing shows up - not even empty graphs - when I click on a device and go to monitor/connections statistics. After a few minutes, I do get an error message that states "Error retrieving connection stats. Please ensure that the device is online and then refresh." By the way, I get all other statics in the GUI such as Optimization Details Report, Traffic Summary Report, etc. Another thing, these WAEs are behind a router and supposedly the ports to allow access to/from the WAEs and other data is allowed through the firewall.
Is there some special port that needs to be opened on the firewall to allow for 'connection statistics' information displayed, that doesn't need to be opened for the other statistics to display? Or could this be a bug in the software?
Cisco :: EPC3825 EuroDocsis 3.0 Gateway / Cannot Get Statistics From This Modem On Snmp
Oct 11, 2012I have the Cisco EPC3825 EuroDocsis 3.0 Gateway and i cannot get statistics from this modem on snmp. Use snmpwalk. Nothing was found in settings of device.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: 7600 Router - NX-OS ACS 4.2 Version
Sep 9, 2012We have ACS 4.2 for our existing IOS routers mainly 7600.We have just integrated Nexus switches.
What is the appropriate ACS version/appliance that will support both the existing IOS routers and new NX-OS switches?
Linksys Wireless Router :: Cannot Clear Or Reset WRT120N To Re-install
Dec 28, 2011I have this router that wouldn't connect because I lost the password. I held the reset button for 90 seconds and it neverwould reset.
View 4 Replies View Related