The 7600 platform support x.25 and XOT features. In ios versión S764AEK9-15103SCisco 7600-RSP720 IOS ADVANCED ENTERPRISE SERVICES SSH The feature navigator display that support this features, but i'dont see these on the other newer ios version. If posible use 7600 for x.25 / xot or maybe will used de 3900 platform?
View 1 RepliesI am looking for the best QoS method for a 7600 series router. We have a 7604 edge router that has remote branch connections to it via GRE tunnels. unfortunately I cannot shape on these GRE tunnels neither can I use bandwidth or priority statements.
View 1 Replies View RelatedWe have ACS 4.2 for our existing IOS routers mainly 7600.We have just integrated Nexus switches.
What is the appropriate ACS version/appliance that will support both the existing IOS routers and new NX-OS switches?
I want to ask about cisco 7600 model is it a switch or router or layer3 switch or Multilayer switch ?
here is the sh version :
===================================
Gateway7600#sh version
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVENTERPRISEK9-M), Version 15.2(1)S, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Sun 27-Nov-11 15:27 by prod_rel_team
[code]....
I have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. URL We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
View 1 Replies View RelatedI have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. [URL] According to our baseline it should not be more than 40% at any given time. We see high CPU uptp 70% consistently.
CPU utilization for five seconds: 99%/0%; one minute: 57%; five minutes: 55%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
442 66173704 90234125 733 96.86% 46.09% 46.30% 0 BGP Router
7 509291060 26330202 19342 1.17% 3.90% 2.99% 0 Check heaps
Router has 1 eBGP session with ISP from where it downloads whole IPv4 internet routing table and two IBGP session with other two rotuer. When I look at BGP summary table I see many updates received from ISP and sent out to IBGP neighbors. Also did debug BGP updates to confirm it.
We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.
%BGP-6-BIGCHUNK: Big chunk pool request 628 for community. Replenishing with malloc
I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
We have cisco 7600 Router with 76-ES+XT-4TG3C Module connected. The Module is getting detected after upgrading the Router with SRD5 IOS.Below are the testing which we have done on the Router but we are facing the issue while configuring the Transport mode LAN and Transport Mode WAN:Brief about this is:- 2 Cisco 7606-s Router with Module 76-ES+XT-4TG3C each.- two ports on 7606-s Ten2/1 & Ten2/2 are configured as a Transport mode WAN while Ten2/3 & Ten2/4 are configured as Transport mode LAN.- We connect Fiber Cable from LAN Port to MUX and from MUX to 2nd LAN Port of the same Router. Same thing we tested by using the WAN Port-MUX-WAN Port connection.- Now on MUX end LAN port, connected Single and Multi mode fiber and on 7606 end 2/4 port which is configured as transport mode LAN, using Multimode SFP module -> XFP-10G-MM-SR, port did not came up then replaced 2/4 port with single mode SFP ->XFP-10GLR-OC192SR port came up. this is testing for LAN.- For WAN testing on MUX end used WAN port and on 7606 end checked with single mode and multimode fiber and with single XFP-10GLR-OC192SR / mulimode XFP-10G-MM-SR SFP, port did not come up.Wanted to know 1) If we have to go for Transport Mode LAN then which SFP/XSFP Module should go with along with the Single/Multimode Fiber.2) If we have to go for Transport Mode WAN then which SFP/XSFP Module should go with along with the Single/Multimode Fiber.Anything else is required while configuring the Transport Mode WAN as this is for Packet-Over_SONET/SDH? 3) MUX Side change is required while connecting both of this Modes on Cisco 7600 Router.4) Is hardware of the Router is giving any issue? Though we tested by connecting Back to Back LAN Port as well as Back to Back WAN Port. In both the situation the Ports are coming UP.
View 1 Replies View Relatedtoday i installed new router 7600 , but im facing some thing the cpu is increasing and it reached 50 % and still increasing as the bw dissipated is increasing .im applying ip policy which set next hop for many internet source my question is , how to know the cu percentage which is used by this ip policy , also , how to know the percentage by access-list ??
View 4 Replies View Relatedhow can I clear the counters of the policy-map statistics in an 7600 and the 1841 router?
View 6 Replies View Relatedwe are using 7609 router. it forwarding traffic to wards my firewall which was not allowd in my router. when ever im checking for routes in router using show ip route x.x.x.x its showing SUBNET IS NOT IN TABLE, but in workmy firewall dropped connection i can able to see that networks.
View 2 Replies View RelatedWhen mutiple Policy based routing configured on 7600 routers, did the router performace degraded with the number of policy based routing rules?Also, did 7600 running 12.x use per-flow based routing or per packet based routing?
View 1 Replies View RelatedHow can we know that 6500 and 7600 series switch and router are running in native mode or in hybrid mode.
View 2 Replies View Relatedi have a query ,we are planning to upgrade the Sup Engine from WS-SUP720-3B 2 ports Supervisor Engine 720 to
RSP720-3CXL-GE=
Cisco 7600 Route Switch Processor 720Gbps fabric,PFC3CXL, GE
Can we use the same old IOS from Sup720 to the New RSP720 without purchasing it ?
Show Version-- Cisco Router 7609
Cisco IOS Software, c7600s72033_rp Software (c7600s72033_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB3, RELEASE SOFTWARE (fc1)ROM: System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
System returned to ROM by power cycle at 08:36:39 PDT Fri Mar 30 2007 (SP by power on)
System restarted at 10:04:20 GMT Fri Nov 25 2011
System image file is "bootdisk:c7600s72033-advipservicesk9-mz.122-33.SRB3.bin"
Last reload type: Normal Reload
[code]....
what is use of haiving SPA and SIP in router hardware ? what if we dont have them in router ?
View 3 Replies View RelatedI need to know if upgrading Cisco IOS on 7600 series router is possible. From 12.2(18)SXF --> 12.2(33)SRC, i need this because SRC supports Lawfull Intercept.
specification of router is 7606
slot 1 - WS-X6708-10GE
slot 1/0 - WS-F6700-DFC3C
slot 4 - WS-X6408A-GBIC
slot 6 - WS-SUP720-3B
slot 6/0 - WS-F6K-PFC3B
slot 6/1 - WS-SUP720
If I have SIP-200 and I need to configure a feature , for eg - PPP on SIP-200 , is it something possible ? If Yes how I can do that in IOS ?
View 1 Replies View RelatedToday i want to ask is cisco 7600 support ip next-hop recusrive x.x.x.x (PBR feature).
View 1 Replies View RelatedWhy below simple PBR is not implemented in H/W knowing the Copp is not configured
NPE-1#sh ver | i image
System image file is "bootdisk:c7600rsp72043-advipservices-mz.122-33.SRE0a"
NPE-1#sh run int GigabitEthernet1/1
interface GigabitEthernet1/1
ip address 11.0.0.1 255.255.255.0
ip pim sparse-mode
[code]...
I am trying to establish a BGP session between a Cisco 7600 and Juniper MX960, but this always stucks in OpenConfirm state.
access-4#show ip bgp v v VRF1 neighbors 166.63.168.197BGP neighbor is 166.63.168.197, vrf VRF1, remote AS 5555, local AS 65533, external link BGP version 4, remote router ID 195.2.1.21 BGP state = OpenConfirm Last read 00:02:27, last write 00:02:27, hold time is 180, keepalive interval is 60 seconds Message statistics: InQ depth is 0 OutQ depth is 0 Sent Rcvd Opens: 4 4 Notifications: 2 1 Updates: 0 0 Keepalives: 4
May 12 13:58:07.531 bst: TCP src=54912, dst=179, seq=1766275951, ack=1681278050, win=17520 ACK PSHMay 12 13:58:07.535 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:53.883 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:59.359 bst: IP: s=166.63.168.197 (Vlan20), d=166.63.168.198, len 61, rcvd 2May 12 13:58:59.359 bst: TCP src=54912, dst=179, seq=1766276010, ack=1681278050, win=17520 ACK PSH FINMay 12 13:58:59.359 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:59.359 bst: %BGP-3-NOTIFICATION: received from neighbor 166.63.168.197 4/0 (hold time expired) 0 bytes
ICMP works fine. It is same on JUniper end. Sending keepalives but cannot receive
###interface configinterface Vlan20 ip vrf forwarding VRF1 ip address 166.63.168.198 255.255.255.252 no ip redirects no ip proxy-arp load-interval 30end
###bgp config
neighbor 166.63.168.197 remote-as 5555 neighbor 166.63.168.197 local-as 65533 neighbor 166.63.168.197 ebgp-multihop 5 neighbor 166.63.168.197 update-source Vlan20 neighbor 166.63.168.197 activate neighbor 166.63.168.197 soft-reconfiguration inbound
I am pretty far out of my comfort zone here but these VS-S720-10G-3C cards were purchased to upgrade our 7609/7606 routers, the spec sheet says they are compatable but I can't find an IOS that "likes" them. I had no problem finding an IOS and using the vss cards in our 6506...
[URL]
what is the use SPA and SIP...in router hardware ? What if we do not have them ?
View 1 Replies View RelatedI have a strange QoS problem with one Cisco7600 (sup7203BXL, IOS 12.2(33)SRE6).
This is layer 2 traffic,and all ports are L2 dot1q trunks:
1) Packet comes with DSCP 46 on Gigabit port (WS6728-SFP) with "mls qos trust dscp" configured. It goes out the port of the same card/slot with DSCP 0.
2) packet comes with DSCP 46 on different Gigabit port on the same card/slot with "mls qos trust dscp" and also "mls qos vlan-based" configured. It qoes out out the port with DSCP 46.
Why the switch behave differently if "mls qos vlan-based" is configured on port (or to say it works correct since it doesn't override DSCP)?
I have global command "mls qos rewrite ip dscp" since this 7600 is also MPLS PE router and I found in documentation that "mls qos rewite ip dscp" is mandatory for QoS on MPLS (EXP bits). So I can't turn off "rewrite ip dscp". Again the problem that I presents is L2 problem not MPLS (MPLS is used for different traffic).
Also mls qos mappings are ok COS to DSCp are 5 to 46 and vice versa.
Furthermore, as far as I know if I have configured "mls qos trust dscp" on Gigabit ethernet port, switch (7600) should work in this order:
- make internal DSCP from packet DSCP
- since I don't have configured DSCP mutation DSCP should stay the same (46)
- using map DSCP - COS ( 46 -5 ) switch will choose queue on outgoing interface in regards to mapped COS
I'm looking for iformation if CFM Local Maintenance End Point configured on Cisco 7606 router is able to respond to the Y.1731 Performance Monitoring (DMM/DMR ).I know I can use IP SLA to configure Y.1731 PM measurements, but I just need a reflector that will answer for incoming DMM messages with DMRs.
View 0 Replies View RelatedYou can configure EoMPLS on a port of the WS-X6724SFP card found in a Cisco 7600 with Supervisor 720.
View 1 Replies View Relatedif the 7600-SIP-200 supported in VSS mode or not ?
I have configured to Cisco Catalyst 6513 as VSS, both of them have the 7600-SIP-200 module, before converting them to VSS I was able to work with the 7600-SIP-200 module, but after I did convert them to VSS, both modules didn't work.
here is the show module output, after VSS conversion:
VSS1#show module Mod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 0 4-subslot SPA Interface Processor-200 7600-SIP-200 JAE14500GMT 7 5 Supervisor Engine 720 10GE
[Code].....
Need to clarify this log message:
*Oct 23 06:20:07 UTC: %FPD_MGMT-3-INCOMP_IMG_VER: Incompatible ROMMON (FPD ID=5) image version detected for 7600-SIP-200 card in slot Detected version = 1.3, minimum required version = 1.4. Current HW version = 2.303.
I would like more information of performance to 7600 router with the SP-720, how many sessions full bgp routing it supports? I have 4 links 1 GB and a throughput of 900 MB.
View 4 Replies View RelatedI have cisco 7600 core router in ISP , i want to put the bandwidth limit on it for outgoing traffic (for internet) on a subnet because i am using Bluecoat and i want to test my bluecoat.On this subnet i have no limit for bluecoat but after the bluecoat i want to limit it. On 7600 cisco router i have not rate limit command so how it can be possible for a perticular subnet ?
View 1 Replies View RelatedI have a 7606 running c7600rsp72043-advipservicesk9-mz.122-33.SRD2.bin with SIP-400 card that has suddenly stopped working, on checking the logs i see the following:
%ONLINE-SP-6-TIMER: Module 3, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 3 set off (Module Failed SCP dnld)
I have tried reseating and even moving it to a different slot but no luck.
%ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 4 set off (Module Failed SCP dnld)
sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 20 ESM20G 7600-ES20-GE3C JAE1237UT90
2 4 7600 ES+ 7600-ES+4TG3CXL JAE13157HIW
3 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAE13219CZH
5 2 Route Switch Processor 720 (Active) RSP720-3C-GE JAE1151819I
6 2 Route Switch Processor 720 (Hot) RSP720-3C-GE JAE11495POH
[code].....
im having lms 4.2.2 and monitoring a cisco 7600 router interface ten gigabit ethernet x/x under dfm. When ever the interface is down due to any media issue i am not getting any alerts in dfm., the interface used to go down for more than 10 minutes. I am able to do an snmpwalk to this interface when the interface was down and getting the value as 2(for down). I am getting other information and configuration mode alerts in dfm for this device.
View 1 Replies View RelatedI posted also under Service Providers for my problem with MPLS/VPN. I just noticed I have the same issue with plain IPV4 BGP. [URL] I have two 7600 running on SRC3 and SRD6. Both acting as RRs.
I noticed that RR1 is reflecting the route to this other 7600 iBGP peer but not installing/importing the route. Other iBGP speakers are able to install and import the route. Is there any issue with 7600 SRC/SRD IOS for Route-reflection?
iBGP policy is similar to all but only the 7600 is unable to install the route. Other 7200 ibgp peers are successful.
Router with 2 RSP RSP720-3C-GE & Image: c7600rsp72043-advipservicesk9-mz.122-33.SRE2.bin We are getting the message as
------------------ show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRE2, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code]....
Show log is attached & we are getting %DHCPD-4-DECLINE_CONFLICT: messages constantly.
I'm trying to find a single device that can both handle Q-in-Q VLAN trunk termination and also TDM cross connects between DS0's on a multi-channel T1 card and DS0's on a multi-channel DS-3 card. I'm looking at a Cisco 7606-S with SUP720's. If I install a 7600-SIP-200 or 7600-SIP-400 with both a SPA-2XCT3/DS0 (channelized T3 card) and a SPA-8XCHT1/E1 (channelized T1 card) will I be able to TDM cross connect the DS0's between the cards? Is there a limit on the number of TDM cross connects? Also, I noticed the CMM cards are EOL. Ideally we'd like to terminate PRI's into the 7606 and run H.323. We'd like to pass voice calls to CUCM and TDM switch FAX calls (via H.323 dial-peer) to a given CAS DS0 on the SPA-2XCT3/DS0. Is this doable with any of the current cards? If not, then we'll stick to the configuration in the first paragraph and only have the 7606 handle the TDM cross connects.
View 3 Replies View Related