Cisco Infrastructure :: 7600 - SIP-400 Not Powering Up?
Oct 10, 2011
I have a 7606 running c7600rsp72043-advipservicesk9-mz.122-33.SRD2.bin with SIP-400 card that has suddenly stopped working, on checking the logs i see the following:
%ONLINE-SP-6-TIMER: Module 3, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 3 set off (Module Failed SCP dnld)
I have tried reseating and even moving it to a different slot but no luck.
%ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 4 set off (Module Failed SCP dnld)
sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 20 ESM20G 7600-ES20-GE3C JAE1237UT90
2 4 7600 ES+ 7600-ES+4TG3CXL JAE13157HIW
3 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAE13219CZH
5 2 Route Switch Processor 720 (Active) RSP720-3C-GE JAE1151819I
6 2 Route Switch Processor 720 (Hot) RSP720-3C-GE JAE11495POH
[code].....
View 4 Replies
ADVERTISEMENT
Jan 19, 2012
what is the use SPA and SIP...in router hardware ? What if we do not have them ?
View 1 Replies
View Related
Apr 4, 2011
I am trying to define a ubr+ service class on PVC for an ATM -SPA (4xOC3 ATM SPA ) but I cannot, I can only implement ubr. According to this link I read that ubr+ is only supported on SVCs. URL
The IOS of my 7600 device is 12.2 (33)SRE2. What I would like to know is there is any other IOS that supports ubr+ under PVCs.
View 1 Replies
View Related
Jan 6, 2013
I have ACE 30 module which is runing on SW 6500 in VSS mode, Vr. 15.0.2 with enugh power avilable ( 2550 W ) , i have insert the module at slot number 7 , the issues am facing it's desribe below :
7/0 ACE Expansion Card 1 ACEMOD-EXPN-DC 1.1 PwrDown
7/1 ACE Expansion Card 2 ACEMOD-EXPN-DC 1.1 PwrDown
And if i take out the blade and insert it again it's work for some time then goes down . here is the consle messages before it goes down :
.ACE platform with 2097152 Kbytes of main memory
.Loading disk0:c6ace-t1k9-mz.A4_1_0.bin. Please wait ....
Uncompressing Linux...
Starting the kernel...
[Code].....
View 2 Replies
View Related
Apr 16, 2012
Does following link/procedure is valid for ASR1004 chassis (STEP4) and not just ASR1013 ?
[URL]
View 6 Replies
View Related
Feb 19, 2013
I use remote Desktop access alot for work but it seems a waste of power as for it to be effective I need to keep the computer on all the time. I have an old Ipod Touch, First Generation that I never use.. I was wondering if it is possible to connect the Ipod Touch to my desktop computer via USB.. If when I finish work I put the computer in sleep mode and then if there is any way that I could access the IPOD via the wifi (which is always on in the building) and make the ipod send a signal to the computer to boot it back up..
View 1 Replies
View Related
Jun 13, 2013
According to the Belkin support tech, apparently the weather (?) may have effected my Belkin Model F5D8235-4 v3 router. My wife pressed the re-set button instead of powering down which according to the tech set my router to reading zero (0).Belkin tech refused to tell me how to re-set the router unless I paid $75 for a six month support plan because mine expired recently.
View 1 Replies
View Related
Jul 10, 2011
i went to bed last night and my router was working fine, but today when i woke up my E2000 had no power it was still plugged in, do you think i fried it? i have only had it sence march and this has never happened before.
View 1 Replies
View Related
Feb 14, 2012
i have 2 cisco 1522 series out door LAP connected to a 3560 POE switch which is not powering up, while ordering my dealer told that it will work with POE, and its go live stage, is there any way to upgrade switch with any IOS version where i can get enough power for 1522?
View 4 Replies
View Related
Apr 9, 2012
We are experiencing two of our layer 3 switches (3560 PoE and 3750 PoE) switches giving us problems with giving power to IP phones. These switches have an embedded PoE module and would previously give power to all IP phones on all its ports. Now all of a sudden over the past few months 6 of these ports have stopped powering phones. The phones are the same ie. 7911 and they take less than 15.4 W. We believe that the PoE module has started malfunctioning and has stopped giving power to all the ports. The port 'grants' power and then removes it. Below is a link showing all the messaged we receive on the terminal session. It is NOT a hardware fault with the PoE: [code]
View 2 Replies
View Related
Dec 16, 2012
it is normal for the WISM2 time to be resetted to default of 1 Jan 2000 after rebooting the 6506E if no NTP is configured?I had to configure it back to the correct time. If not, the APs will not come up.Also, does the ap or wlc keep track of the ap group the ap is provisioned to?
View 3 Replies
View Related
Nov 4, 2011
Which smaller POE switch is capable of powering a 9971 IP phone with a cam and a think client attached?
View 3 Replies
View Related
Jan 31, 2013
i have a query ,we are planning to upgrade the Sup Engine from WS-SUP720-3B 2 ports Supervisor Engine 720 to
RSP720-3CXL-GE=
Cisco 7600 Route Switch Processor 720Gbps fabric,PFC3CXL, GE
Can we use the same old IOS from Sup720 to the New RSP720 without purchasing it ?
Show Version-- Cisco Router 7609
Cisco IOS Software, c7600s72033_rp Software (c7600s72033_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB3, RELEASE SOFTWARE (fc1)ROM: System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
System returned to ROM by power cycle at 08:36:39 PDT Fri Mar 30 2007 (SP by power on)
System restarted at 10:04:20 GMT Fri Nov 25 2011
System image file is "bootdisk:c7600s72033-advipservicesk9-mz.122-33.SRB3.bin"
Last reload type: Normal Reload
[code]....
View 3 Replies
View Related
Jan 19, 2012
what is use of haiving SPA and SIP in router hardware ? what if we dont have them in router ?
View 3 Replies
View Related
Mar 6, 2011
I need to know if upgrading Cisco IOS on 7600 series router is possible. From 12.2(18)SXF --> 12.2(33)SRC, i need this because SRC supports Lawfull Intercept.
specification of router is 7606
slot 1 - WS-X6708-10GE
slot 1/0 - WS-F6700-DFC3C
slot 4 - WS-X6408A-GBIC
slot 6 - WS-SUP720-3B
slot 6/0 - WS-F6K-PFC3B
slot 6/1 - WS-SUP720
View 1 Replies
View Related
Dec 5, 2012
The 7600 platform support x.25 and XOT features. In ios versión S764AEK9-15103SCisco 7600-RSP720 IOS ADVANCED ENTERPRISE SERVICES SSH The feature navigator display that support this features, but i'dont see these on the other newer ios version. If posible use 7600 for x.25 / xot or maybe will used de 3900 platform?
View 1 Replies
View Related
Jan 19, 2012
If I have SIP-200 and I need to configure a feature , for eg - PPP on SIP-200 , is it something possible ? If Yes how I can do that in IOS ?
View 1 Replies
View Related
May 16, 2012
Today i want to ask is cisco 7600 support ip next-hop recusrive x.x.x.x (PBR feature).
View 1 Replies
View Related
Nov 19, 2011
Why below simple PBR is not implemented in H/W knowing the Copp is not configured
NPE-1#sh ver | i image
System image file is "bootdisk:c7600rsp72043-advipservices-mz.122-33.SRE0a"
NPE-1#sh run int GigabitEthernet1/1
interface GigabitEthernet1/1
ip address 11.0.0.1 255.255.255.0
ip pim sparse-mode
[code]...
View 4 Replies
View Related
May 11, 2011
I am trying to establish a BGP session between a Cisco 7600 and Juniper MX960, but this always stucks in OpenConfirm state.
access-4#show ip bgp v v VRF1 neighbors 166.63.168.197BGP neighbor is 166.63.168.197, vrf VRF1, remote AS 5555, local AS 65533, external link BGP version 4, remote router ID 195.2.1.21 BGP state = OpenConfirm Last read 00:02:27, last write 00:02:27, hold time is 180, keepalive interval is 60 seconds Message statistics: InQ depth is 0 OutQ depth is 0 Sent Rcvd Opens: 4 4 Notifications: 2 1 Updates: 0 0 Keepalives: 4
May 12 13:58:07.531 bst: TCP src=54912, dst=179, seq=1766275951, ack=1681278050, win=17520 ACK PSHMay 12 13:58:07.535 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:53.883 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:59.359 bst: IP: s=166.63.168.197 (Vlan20), d=166.63.168.198, len 61, rcvd 2May 12 13:58:59.359 bst: TCP src=54912, dst=179, seq=1766276010, ack=1681278050, win=17520 ACK PSH FINMay 12 13:58:59.359 bst: IP: tableid=2, s=166.63.168.198 (local), d=166.63.168.197 (Vlan20), routed via FIBMay 12 13:58:59.359 bst: %BGP-3-NOTIFICATION: received from neighbor 166.63.168.197 4/0 (hold time expired) 0 bytes
ICMP works fine. It is same on JUniper end. Sending keepalives but cannot receive
###interface configinterface Vlan20 ip vrf forwarding VRF1 ip address 166.63.168.198 255.255.255.252 no ip redirects no ip proxy-arp load-interval 30end
###bgp config
neighbor 166.63.168.197 remote-as 5555 neighbor 166.63.168.197 local-as 65533 neighbor 166.63.168.197 ebgp-multihop 5 neighbor 166.63.168.197 update-source Vlan20 neighbor 166.63.168.197 activate neighbor 166.63.168.197 soft-reconfiguration inbound
View 1 Replies
View Related
Nov 5, 2012
I am pretty far out of my comfort zone here but these VS-S720-10G-3C cards were purchased to upgrade our 7609/7606 routers, the spec sheet says they are compatable but I can't find an IOS that "likes" them. I had no problem finding an IOS and using the vss cards in our 6506...
[URL]
View 3 Replies
View Related
Oct 16, 2012
I have a strange QoS problem with one Cisco7600 (sup7203BXL, IOS 12.2(33)SRE6).
This is layer 2 traffic,and all ports are L2 dot1q trunks:
1) Packet comes with DSCP 46 on Gigabit port (WS6728-SFP) with "mls qos trust dscp" configured. It goes out the port of the same card/slot with DSCP 0.
2) packet comes with DSCP 46 on different Gigabit port on the same card/slot with "mls qos trust dscp" and also "mls qos vlan-based" configured. It qoes out out the port with DSCP 46.
Why the switch behave differently if "mls qos vlan-based" is configured on port (or to say it works correct since it doesn't override DSCP)?
I have global command "mls qos rewrite ip dscp" since this 7600 is also MPLS PE router and I found in documentation that "mls qos rewite ip dscp" is mandatory for QoS on MPLS (EXP bits). So I can't turn off "rewrite ip dscp". Again the problem that I presents is L2 problem not MPLS (MPLS is used for different traffic).
Also mls qos mappings are ok COS to DSCp are 5 to 46 and vice versa.
Furthermore, as far as I know if I have configured "mls qos trust dscp" on Gigabit ethernet port, switch (7600) should work in this order:
- make internal DSCP from packet DSCP
- since I don't have configured DSCP mutation DSCP should stay the same (46)
- using map DSCP - COS ( 46 -5 ) switch will choose queue on outgoing interface in regards to mapped COS
View 0 Replies
View Related
Jan 14, 2013
I'm looking for iformation if CFM Local Maintenance End Point configured on Cisco 7606 router is able to respond to the Y.1731 Performance Monitoring (DMM/DMR ).I know I can use IP SLA to configure Y.1731 PM measurements, but I just need a reflector that will answer for incoming DMM messages with DMRs.
View 0 Replies
View Related
Mar 20, 2012
You can configure EoMPLS on a port of the WS-X6724SFP card found in a Cisco 7600 with Supervisor 720.
View 1 Replies
View Related
Mar 26, 2011
if the 7600-SIP-200 supported in VSS mode or not ?
I have configured to Cisco Catalyst 6513 as VSS, both of them have the 7600-SIP-200 module, before converting them to VSS I was able to work with the 7600-SIP-200 module, but after I did convert them to VSS, both modules didn't work.
here is the show module output, after VSS conversion:
VSS1#show module Mod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 0 4-subslot SPA Interface Processor-200 7600-SIP-200 JAE14500GMT 7 5 Supervisor Engine 720 10GE
[Code].....
View 1 Replies
View Related
Oct 22, 2012
Need to clarify this log message:
*Oct 23 06:20:07 UTC: %FPD_MGMT-3-INCOMP_IMG_VER: Incompatible ROMMON (FPD ID=5) image version detected for 7600-SIP-200 card in slot Detected version = 1.3, minimum required version = 1.4. Current HW version = 2.303.
View 1 Replies
View Related
Dec 7, 2010
I would like more information of performance to 7600 router with the SP-720, how many sessions full bgp routing it supports? I have 4 links 1 GB and a throughput of 900 MB.
View 4 Replies
View Related
Apr 29, 2012
I have cisco 7600 core router in ISP , i want to put the bandwidth limit on it for outgoing traffic (for internet) on a subnet because i am using Bluecoat and i want to test my bluecoat.On this subnet i have no limit for bluecoat but after the bluecoat i want to limit it. On 7600 cisco router i have not rate limit command so how it can be possible for a perticular subnet ?
View 1 Replies
View Related
Nov 2, 2012
im having lms 4.2.2 and monitoring a cisco 7600 router interface ten gigabit ethernet x/x under dfm. When ever the interface is down due to any media issue i am not getting any alerts in dfm., the interface used to go down for more than 10 minutes. I am able to do an snmpwalk to this interface when the interface was down and getting the value as 2(for down). I am getting other information and configuration mode alerts in dfm for this device.
View 1 Replies
View Related
Oct 14, 2011
I posted also under Service Providers for my problem with MPLS/VPN. I just noticed I have the same issue with plain IPV4 BGP. [URL] I have two 7600 running on SRC3 and SRD6. Both acting as RRs.
I noticed that RR1 is reflecting the route to this other 7600 iBGP peer but not installing/importing the route. Other iBGP speakers are able to install and import the route. Is there any issue with 7600 SRC/SRD IOS for Route-reflection?
iBGP policy is similar to all but only the 7600 is unable to install the route. Other 7200 ibgp peers are successful.
View 1 Replies
View Related
Jan 14, 2011
Router with 2 RSP RSP720-3C-GE & Image: c7600rsp72043-advipservicesk9-mz.122-33.SRE2.bin We are getting the message as
------------------ show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRE2, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code]....
Show log is attached & we are getting %DHCPD-4-DECLINE_CONFLICT: messages constantly.
View 6 Replies
View Related
Oct 11, 2011
I'm trying to find a single device that can both handle Q-in-Q VLAN trunk termination and also TDM cross connects between DS0's on a multi-channel T1 card and DS0's on a multi-channel DS-3 card. I'm looking at a Cisco 7606-S with SUP720's. If I install a 7600-SIP-200 or 7600-SIP-400 with both a SPA-2XCT3/DS0 (channelized T3 card) and a SPA-8XCHT1/E1 (channelized T1 card) will I be able to TDM cross connect the DS0's between the cards? Is there a limit on the number of TDM cross connects? Also, I noticed the CMM cards are EOL. Ideally we'd like to terminate PRI's into the 7606 and run H.323. We'd like to pass voice calls to CUCM and TDM switch FAX calls (via H.323 dial-peer) to a given CAS DS0 on the SPA-2XCT3/DS0. Is this doable with any of the current cards? If not, then we'll stick to the configuration in the first paragraph and only have the 7606 handle the TDM cross connects.
View 3 Replies
View Related
Oct 18, 2012
I am looking for the best QoS method for a 7600 series router. We have a 7604 edge router that has remote branch connections to it via GRE tunnels. unfortunately I cannot shape on these GRE tunnels neither can I use bandwidth or priority statements.
View 1 Replies
View Related
