Cisco WAN :: 7600 - High CPU Usage BGP Router Process
Sep 12, 2012
I have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. [URL] According to our baseline it should not be more than 40% at any given time. We see high CPU uptp 70% consistently.
CPU utilization for five seconds: 99%/0%; one minute: 57%; five minutes: 55%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
442 66173704 90234125 733 96.86% 46.09% 46.30% 0 BGP Router
7 509291060 26330202 19342 1.17% 3.90% 2.99% 0 Check heaps
Router has 1 eBGP session with ISP from where it downloads whole IPv4 internet routing table and two IBGP session with other two rotuer. When I look at BGP summary table I see many updates received from ISP and sent out to IBGP neighbors. Also did debug BGP updates to confirm it.
We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.
%BGP-6-BIGCHUNK: Big chunk pool request 628 for community. Replenishing with malloc
I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
I have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. URL We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
in both case some times i obtain lowing traffic on interface and highest cpu - to 100% after clear cef linicard i obtain growing traffic and cpu 0%
#sh proc cpu s CPU utilization for five seconds: 87%/83%; one minute: 91%; five minutes: 96% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 7 1711512 87883 19474 4.06% 0.84% 0.89% 0 Check heaps
We suddenly noticed high CPU utilization on one of our 7600 routers. I output of show process CPU showed high utlization for the FM core process. I looked it up but did not find information on what this process does. [code]
i have cisco 7600 router , here is show run : Gateway7600#sh run Building configuration...
Current configuration : 4787 bytes ! ! Last configuration change at 09:08:04 UTC Sat Apr 20 2013 by xxxx ! version 15.2 service timestamps debug datetime msec [Code]....
I'm thinking of purchasing a Cisco Linksys EA6500. I need a router that can one monitor bandwidth used by device. Keep exceeding our ISP's network bandwidth allocation, need to identify the devices that are causing this high usage and be able to do so from the router. Does the EA6500's standard software support this, is their router software one can obtain for the unit that does this or is there another home router option that can perform this function?
We have a Cisco 886 configured with two WAN's (ATM0 connected to a DSL line and Fa3 connected to a CMTS modem).We're running DMVPN over the Cable network and GetVPN over the DSL line. When the DSL line is down we see a lot of CPU peaks up to 90%.The CPU peaks are caused by the process "DSL state machine". As soon as the DSL line has sync and the ATM0 interface goes UP the CPU peaks disappear. What we'd like to know is if this constant extra CPU load will have an impact on other resources like normal routing & switching or more specific IPSEC handling. Is it for example possible that establishing an IPSEC tunnel will fail because of the CPU peaks?
I have in my router 2801, one link with 20 MB WAN Connection, and it is presenting high cpu utilization with 97% Interrupt Errors when start one download.
I exchanged it to another router the 2811 and it presented the same results. I read the cisco document about Router Performance.
And it speaks about the 2801 supports 46 Mbps using CEF/Fast Switching and 1.5Mbps using only Process Switching, and 2811 supports 61.44 CEF and 1.5Mbps Process Switching.
I need to know if the NAT Process is process switching or CEF Switching. Because if it was process switching the router is working in the max capacity and i will need to exchange the hardware to a better hardware.
I have a process whick take all the CPU on two differents Stack of WS-C3750G in version 12.2.53(SE2):
XFRPALSN02R#sh proc cpu sorted CPU utilization for five seconds: 97%/3%; one minute: 95%; five minutes: 95% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 307 5450059 4167397 1307 86.74% 83.63% 83.35% 0 hulc nrgyz PD di XFRPALSN02R#sh proc cpu sorted CPU utilization for five seconds: 96%/3%; one minute: 96%; five minutes: 96% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 307 7779608 5947379 1308 86.26% 85.75% 85.30% 0 hulc nrgyz PD di
Each time I enter show run on my router 2821, it takes ages to display and I have a cpu peak from the ssh process ( I am connected through SSH)
RTR-2821-01#sh proc cpu sorted CPU utilization for five seconds: 96%/21%; one minute: 34%; five minutes: 22% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 55 26948 814 33105 74.96% 16.92% 5.87% 323 SSH Process
I have a router 3845 with c3845-advsecurityk9-mz.124-24.T6.bin software . Frequently we are facing problem in logging to the device .Inorder to resolve we need to reboot the router . Yesterday fortunately i have got the console access for some time so i came to know that TPLUS process is consuming 99.9% percentage cpu.
System returned to ROM by reloadSystem restarted at 00:36:52 UTC Sat Dec 10 2011System image file is "bootflash:cat4000-i9s-mz.122-25.EWA14.bin" cisco WS-C4506 (MPC8245) processor (revision 10) with 262144K bytes of memory.MPC8245 CPU at 266Mhz, Supervisor II+Last reset from Reload1 Virtual Ethernet interface144 FastEthernet interfaces2 Gigabit Ethernet interfaces511K bytes of non-volatile configuration memory.Configuration register is 0x2102
We are experiencing with high CPU input due to ARP input between 20:30 and 22:30 every day At this time we have a lot of backup operations. When I look the netflow report, I can't see anything anormal.
We are changing our backup server's NIC card from 1gig to 10Gig. The backup operation's traffic is high (approx 2Gbps level) but 6509 has to be handle this size of traffic.
We are using two 6509E in VSS mode and our image version is s72033-adventerprisek9_wan-mz.122-33.SXJ.bin
20:00 show ip arp summary -------------- 2588 IP ARP entries, with 166 of them incomplete
I'm facing high CPU utilization issue due to a ssh process on 3750 switch. What is the use of SSH proces in the switch? Can I disable it for troubleshooting?
will there be any impact if I disable it?
#sh processes cpu sorted 5min
CPU utilization for five seconds: 99%/0%; one minute: 66%; five minutes: 46%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 159 1896078 589986 3213 3.96% 10.76% 14.00% 0 Hulc LED Process 165 32871 591 55619 77.42% 33.40% 8.85% 3 SSH Process
we are using Cisco 6509-E VSS mode [12.2(33)SXI] ipbase image and facing high cpu utilization. In show process cpu output it is showing some "ios-base" process consuming cpu. I attached show cpu output
I have a Catalyst Switch 6000. Inoticed that after the execution of the job inventory in LMS, and after the snmp queries reached the equipement, the cpu value reached 98-99 % due to the process : PDU DISPATCHER (what’s it ?)
I have also a script running in the switch to observe the differents logs. For exemple, when high cpu is obtained, the message bellow appear :
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
When a physical switchport/routed port has high usage, you can move the link to a higher capacity port, upgrade the port, bond links, etc. What exactly do you do when an SVI has high usage? I guess you could remove some servers from the VLAN, but that doesn't seem like a reasonable solution. What dictates the capacity of an SVI? The backplane of the switch?
I have a 1841 router plugged into a 100M Comcast ethernet connection. My router cpu is really high and users download speed isn't as high as before. Can a 1841 handle 100M circuit with 100 users on it? What would cause the router's cpu to be high? I don't think there are any viruses or malware on the lan.
#sh proc cpu his r2.leaguecity-toy-startoy 06:06:26 PM Wednesday May 30 2012 PST 111 1 1 1 111 24 1 1 1 1 400369232222544222330359645223283294332688334452308404382236
I have a lot of cisco 7206 vxr deviceses. I have a high cpu problem.I have a 7206 vxr g2. I used to use ebgp for three upstream carrier. I used to bgp full route table method. I have about 800 Mbps active traffics and behing the router about 1600 active customers.
How can I trouble shoot this high cpu problem?
#sh int gigabitEthernet 0/1 GigabitEthernet0/1 is up, line protocol is up Hardware is MV64460 Internal MAC, address is 000c.cf1d.d01b (bia 000c.cf1d.d01b) Description: ***** GW Interface ***** [Code]....
I have a Cisco 1921 router and it uses 99% of CPU and i cant seem to spot wich process that is taking up the cpu. I have an interface with several sub-interfaces and i am moving data between two of those subnets, i tried the "ip route-cache same-interface"-command on giga bit ethernet 0/1 with all the sub-interfaces like gigabitethernet 0/1.18 and so on. That did not work.
Received this notice from ISP. Does this make sense:We have noticed we are getting a huge number of queries from X.X.X.X and it is showing to be about 98% of the DNS traffic hitting our name servers. It appears that the data consists of reverse lookups to 10.1.0.0 network. It needs to be remediated as soon as possible because it could cause a service interruption.It almost seems as if my router is acting as a DNS server. The isp data consists of reverse lookups to 10.1.0.0 network which would be the internal.
I am a little stuck trying to troubleshoot unusually high cpu on 7600 Platform.This has been going on for many hours and not been causing a problem, but this doesn't seem replicated in our network and I am concerned about the cause.I have attached some output below, and disabled netflow on interfaces to free some switching CPU. How to track the cause of this? We only have routing protocols and 5 static routes to Null 0, so I cant see how this can be a route loop, but willing to stand corrected. Routes are learned from BGP with OSPF/MPLS internally on the network. This switch also connects to access switches on RIP and EIGRP.
No change has been made to this device when this problem started to occur so I am suspecting something about the traffic has changed or there is a rougue user? [code]
I've got a problem with a core 6509E and the multicast.A client has a system with cams for the physical security and they are connected to a vlan with this config:
interface VlanXip address 172.20.167.1 255.255.255.128ip helper-address 172.20.32.7ip pim version 1ip pim sparse-modeendThe thing is that we know that one server that shows the cams at the security office is flooding the network and the CPU CORE is over 95% always:
CPU utilization for five seconds: 99%/39%; one minute: 99%; five minutes: 99% 263 644650276 567873287 1135 51.99% 55.06% 55.35% 0 IP Input [Code] ....
i keep getting messages from AVG saying they have detected a very high internet usage, first it was with google and then with firefox..they recommended to shut down and restart..anyone could explain what's going on? I'm not downloadin anything..just checking my mail!
