Each time I enter show run on my router 2821, it takes ages to display and I have a cpu peak from the ssh process ( I am connected through SSH)
RTR-2821-01#sh proc cpu sorted
CPU utilization for five seconds: 96%/21%; one minute: 34%; five minutes: 22%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
55 26948 814 33105 74.96% 16.92% 5.87% 323 SSH Process
We suddenly noticed high CPU utilization on one of our 7600 routers. I output of show process CPU showed high utlization for the FM core process. I looked it up but did not find information on what this process does. [code]
View 4 Replies View Relatedwe are using Cisco 6509-E VSS mode [12.2(33)SXI] ipbase image and facing high cpu utilization. In show process cpu output it is showing some "ios-base" process consuming cpu. I attached show cpu output
View 1 Replies View RelatedWe are running a stack of 2 WS-C3750X-24S-E's with IOS version 12.2(58)SE2 and we are seeing continuous high processor utilization involving the hl3mm process. The stack is configured for PIM Sparse mode, with 2 upstream Nexus 5596'es acting as both RP candidates and as BSRs. The hl3mm process generally runs at about 19% but can spike up into the 60% range.Symptoms on the 3750X are spiking latency and sluggish CLI perfformance. I thought at first that we might be running into SDM limits, but the "show platform tcam utilization" show that we are far under the limits of the default SDM template. Performing the "show ip pim (vrf name) bsr-router" command freezes the system and takes 20-30 seconds to return results. Similiarly configured WS-C3750G-12S running 12.2(55)SE3 does not exhibit these same issues.
View 4 Replies View Relatedwhy I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedIn Cisco 7206 VXR (NPE-G2) router , the CPU utilization is at an 80-90% always , but none of the process is consuming not more than 1%. In the show stacks output we are observing network interface interrupt is called very frequently. so what does network interface interrupt is about. Logs for the reference: show process CPU sorted
CPU utilization for five seconds: 88%/88%; one minute: 89%; five minutes: 89%
PID Runtime(uS) Invoked u Secs 5Sec 1Min 5Min TTY Process
1 0 72 0 0.00% 0.00% 0.00% 0 Chunk Manager
2 20020000 17159 1166 0.00% 0.02% 0.01% 0 Load Meter
[Code]...
We have a Cisco 886 configured with two WAN's (ATM0 connected to a DSL line and Fa3 connected to a CMTS modem).We're running DMVPN over the Cable network and GetVPN over the DSL line. When the DSL line is down we see a lot of CPU peaks up to 90%.The CPU peaks are caused by the process "DSL state machine". As soon as the DSL line has sync and the ATM0 interface goes UP the CPU peaks disappear. What we'd like to know is if this constant extra CPU load will have an impact on other resources like normal routing & switching or more specific IPSEC handling. Is it for example possible that establishing an IPSEC tunnel will fail because of the CPU peaks?
View 11 Replies View RelatedI have in my router 2801, one link with 20 MB WAN Connection, and it is presenting high cpu utilization with 97% Interrupt Errors when start one download.
I exchanged it to another router the 2811 and it presented the same results. I read the cisco document about Router Performance.
And it speaks about the 2801 supports 46 Mbps using CEF/Fast Switching and 1.5Mbps using only Process Switching, and 2811 supports 61.44 CEF and 1.5Mbps Process Switching.
I need to know if the NAT Process is process switching or CEF Switching. Because if it was process switching the router is working in the max capacity and i will need to exchange the hardware to a better hardware.
I have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. URL We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
View 1 Replies View RelatedI have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. [URL] According to our baseline it should not be more than 40% at any given time. We see high CPU uptp 70% consistently.
CPU utilization for five seconds: 99%/0%; one minute: 57%; five minutes: 55%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
442 66173704 90234125 733 96.86% 46.09% 46.30% 0 BGP Router
7 509291060 26330202 19342 1.17% 3.90% 2.99% 0 Check heaps
Router has 1 eBGP session with ISP from where it downloads whole IPv4 internet routing table and two IBGP session with other two rotuer. When I look at BGP summary table I see many updates received from ISP and sent out to IBGP neighbors. Also did debug BGP updates to confirm it.
We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.
%BGP-6-BIGCHUNK: Big chunk pool request 628 for community. Replenishing with malloc
I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
I have a process whick take all the CPU on two differents Stack of WS-C3750G in version 12.2.53(SE2):
XFRPALSN02R#sh proc cpu sorted CPU utilization for five seconds: 97%/3%; one minute: 95%; five minutes: 95% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 307 5450059 4167397 1307 86.74% 83.63% 83.35% 0 hulc nrgyz PD di XFRPALSN02R#sh proc cpu sorted CPU utilization for five seconds: 96%/3%; one minute: 96%; five minutes: 96% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 307 7779608 5947379 1308 86.26% 85.75% 85.30% 0 hulc nrgyz PD di
i try newest ios 15.1(3)S0a and 12.2(33)SRE
in both case some times i obtain lowing traffic on interface and highest cpu - to 100%
after clear cef linicard i obtain growing traffic and cpu 0%
#sh proc cpu s
CPU utilization for five seconds: 87%/83%; one minute: 91%; five minutes: 96%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
7 1711512 87883 19474 4.06% 0.84% 0.89% 0 Check heaps
[Code].....
Based on the stace trace, how do I determine what object is being polled??? (what is causing the high cpu for SNMP ENGINE)
From the “show stack 295” output (SNMP ENGINE)
router>show stack 295
Process 295: SNMP ENGINE
Stack segment 0x68226DC0 - 0x68229CA0
FP: 0x68229BD0, RA: 0x62A0D95C
FP: 0x68229BF8, RA: 0x628276A8
FP: 0x68229C68, RA: 0x629FBE08
FP: 0x68229C80, RA: 0x629FBDEC
Our switch is very high cpu in process arp
Am debug ip arp track command the result as below
-- on this switch have interface vlan 201 ip subnet is 10.11.201.1/24
Jun 5 15:30:40.732 GMT+7: IP ARP: rcvd req src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116.73 Vlan201
Jun 5 15:30:42.150 GMT+7: IP ARP: rcvd rep src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116.4 Vlan201
Jun 5 15:30:42.150 GMT+7: IPARP_TRACK: ARP tableid(0) 10.11.201.217 Vlan201 mode(1) modified.
Jun 5 15:30:42.150 GMT+7: IP ARP: rcvd req src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116
and then am try to shutdown vlan database 201 after that the cpu process has to normal state.
How to check the root cacus?
I have a router 3845 with c3845-advsecurityk9-mz.124-24.T6.bin software . Frequently we are facing problem in logging to the device .Inorder to resolve we need to reboot the router . Yesterday fortunately i have got the console access for some time so i came to know that TPLUS process is consuming 99.9% percentage cpu.
View 1 Replies View RelatedI have a problem with cpu high.tell me if normal have this process?
CPU utilization for five seconds: 29%/0%; one minute: 29%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
29 198216576 402619350 492 15.83% 15.87% 15.68% 0 Cat4k Mgmt HiPri
30 175197296 96703435 1811 10.23% 10.10% 10.64% 0 Cat4k Mgmt LoPri
Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.2(25)EWA14, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Tue 20-May-08 18:49 by chendahImage text-base: 0x10000000, data-base: 0x114BE208
ROM: 12.2(31r)SG2Dagobah Revision 226, Swamp Revision 34
System returned to ROM by reloadSystem restarted at 00:36:52 UTC Sat Dec 10 2011System image file is "bootflash:cat4000-i9s-mz.122-25.EWA14.bin" cisco WS-C4506 (MPC8245) processor (revision 10) with 262144K bytes of memory.MPC8245 CPU at 266Mhz, Supervisor II+Last reset from Reload1 Virtual Ethernet interface144 FastEthernet interfaces2 Gigabit Ethernet interfaces511K bytes of non-volatile configuration memory.Configuration register is 0x2102
We are experiencing with high CPU input due to ARP input between 20:30 and 22:30 every day At this time we have a lot of backup operations. When I look the netflow report, I can't see anything anormal.
We are changing our backup server's NIC card from 1gig to 10Gig. The backup operation's traffic is high (approx 2Gbps level) but 6509 has to be handle this size of traffic.
We are using two 6509E in VSS mode and our image version is s72033-adventerprisek9_wan-mz.122-33.SXJ.bin
20:00
show ip arp summary
--------------
2588 IP ARP entries, with 166 of them incomplete
[Code].....
I'm facing high CPU utilization issue due to a ssh process on 3750 switch. What is the use of SSH proces in the switch? Can I disable it for troubleshooting?
will there be any impact if I disable it?
#sh processes cpu sorted 5min
CPU utilization for five seconds: 99%/0%; one minute: 66%; five minutes: 46%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
159 1896078 589986 3213 3.96% 10.76% 14.00% 0 Hulc LED Process
165 32871 591 55619 77.42% 33.40% 8.85% 3 SSH Process
which process is consuming high memory with my c6509 switch.
View 17 Replies View RelatedI have a Catalyst Switch 6000. Inoticed that after the execution of the job inventory in LMS, and after the snmp queries reached the equipement, the cpu value reached 98-99 % due to the process : PDU DISPATCHER (what’s it ?)
I have also a script running in the switch to observe the differents logs. For exemple, when high cpu is obtained, the message bellow appear :
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
....
We've just discovered it seems the 2800 series aren't getting IOS 15.2?
We're running a 2851 for our CME and specifically want some features in CME 8.8...
End of Sale has been announced, but as it stands you can still purchase this router new today.
What causes LMS 4.1 to have high memory utilization?
View 4 Replies View RelatedOur Router 7606 is in a problem with high CPU Utilization. We are using one EBGP and one IBGP session. We are also running OSPF with area 0 between two IBGP router to exchange few local networks. When bandwidth cross 100 MB than only CPU use become 100%. when bandwidth consumption is 80MB CPU use become 80% end so on.
Out put is when bandwidth consumption is 34MB
CPU utilization for five seconds: 44%/43%; one minute: 42%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
78 44 9625 4 0.39% 0.03% 0.00% 2 Virtual Exec
13 40 375 106 0.07% 0.00% 0.00% 0 ARP Input
30 116 1098 105 0.07% 0.01% 0.00% 0 IPC Seat Manager
[code]....
I have a hight CPU utilisation problem in my CISCO7609-S routers. the cpu utilisation can rise 99% et this is usually. In the moment of hight CPU the the process CPU give the following:
the show processe cpu history give: show version
I have a 2811 that is really hitting the CPU hard. Nothing shows on CPU processes. It has an IPsec VPN tunnel back to HQ which also has a 2811 that terminates the VPN. The HQ has 2-3 IPsec tunnels to other remote sites. The CPU at the HQ avg 50% utilization during business hrs, peaks at about 80%. The remote one is very high 95% peaks, avg 80%-95% during business hours with bandwidth utilization of only 10-20Mbps. I read somewhere that its possible that fragmentation could be causing this. My question is, if I set the MTU to 1450 on the remote, I am guessing I will need to do all the other routers as well, the HQ and other remote sites? Siince they use the same outside interface to my HQ, is that correct?
View 3 Replies View RelatedWe have Cisco 2811 router and facing high CPU utilisation as 70%/67%;,IOS Runing :c2800nm-advsecurityk9-mz.124-3f.bin.
View 4 Replies View RelatedHigh cpu utilization on cisco 7206 vxr router.[code]
View 2 Replies View RelatedI am observing very high CPU utilization on my Cisco 7206VXR (NPE-G1) Router. We have done all the necessary troubleshooting but not able to identify root cause. [code]
View 10 Replies View RelatedI am running Cisco Prime 4.2(UNIX version) on a VM. CPU utilization will run between 90 and 100% constantly. Reloading the server will stabilize the CPU for a short period of time, however the CPU usage will always return to 90-100% utilization. Currently I have about 130 devices added to the system.
View 1 Replies View Relatedwe have 2 Cisco C4507 Switches working As Core Layer, but the CPU Utilization is about 54% most of the time and sometimes it goes up to 70% or 80% also.
which services are causing this utilization. [code]
we have cisco 4510+R switch with Cisco IOS-XE software & we are facing high cpu utilization on core 1 (95%) & on core 0 (15%) since last 2 hours.
I have taken logg file but did not understand how to analyzed it & where is problem. log file is attached.
I am working as net admin which is i need to monitoring and manage my workplace network( education center )I got a few question about network traffic flow. Here is the issued.I got high bandwidth utilization so high after office hours which is only on night. as we know, after office hours there is no person at the office but the traffic flow on bandwidth utilization is high.what are the possibilities of this issued?
View 1 Replies View Relatedi have one cisco router 2811 now its not booting normally.
Router was working without any problems but due to power loss router restarted and goes into rommon mode
I tried to boot from flash and usbfalsh with different images but no use router is in still rommon mode.
here the output of my router:
program load complete, entry point: 0x8000f000, size: 0x3117470
Error : compressed image checksum is incorrect 0x8E095E7F
Expected a checksum of 0x8E0AE77F
*** System received a Software forced crash ***
signal= 0x17, code= 0x5, context= 0x80014e20
[Code].....