I have a router 3845 with c3845-advsecurityk9-mz.124-24.T6.bin software . Frequently we are facing problem in logging to the device .Inorder to resolve we need to reboot the router . Yesterday fortunately i have got the console access for some time so i came to know that TPLUS process is consuming 99.9% percentage cpu.
View 1 RepliesI have a process whick take all the CPU on two differents Stack of WS-C3750G in version 12.2.53(SE2):
XFRPALSN02R#sh proc cpu sorted CPU utilization for five seconds: 97%/3%; one minute: 95%; five minutes: 95% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 307 5450059 4167397 1307 86.74% 83.63% 83.35% 0 hulc nrgyz PD di XFRPALSN02R#sh proc cpu sorted CPU utilization for five seconds: 96%/3%; one minute: 96%; five minutes: 96% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 307 7779608 5947379 1308 86.26% 85.75% 85.30% 0 hulc nrgyz PD di
i try newest ios 15.1(3)S0a and 12.2(33)SRE
in both case some times i obtain lowing traffic on interface and highest cpu - to 100%
after clear cef linicard i obtain growing traffic and cpu 0%
#sh proc cpu s
CPU utilization for five seconds: 87%/83%; one minute: 91%; five minutes: 96%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
7 1711512 87883 19474 4.06% 0.84% 0.89% 0 Check heaps
[Code].....
Our switch is very high cpu in process arp
Am debug ip arp track command the result as below
-- on this switch have interface vlan 201 ip subnet is 10.11.201.1/24
Jun 5 15:30:40.732 GMT+7: IP ARP: rcvd req src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116.73 Vlan201
Jun 5 15:30:42.150 GMT+7: IP ARP: rcvd rep src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116.4 Vlan201
Jun 5 15:30:42.150 GMT+7: IPARP_TRACK: ARP tableid(0) 10.11.201.217 Vlan201 mode(1) modified.
Jun 5 15:30:42.150 GMT+7: IP ARP: rcvd req src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116
and then am try to shutdown vlan database 201 after that the cpu process has to normal state.
How to check the root cacus?
I have a problem with cpu high.tell me if normal have this process?
CPU utilization for five seconds: 29%/0%; one minute: 29%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
29 198216576 402619350 492 15.83% 15.87% 15.68% 0 Cat4k Mgmt HiPri
30 175197296 96703435 1811 10.23% 10.10% 10.64% 0 Cat4k Mgmt LoPri
Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.2(25)EWA14, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Tue 20-May-08 18:49 by chendahImage text-base: 0x10000000, data-base: 0x114BE208
ROM: 12.2(31r)SG2Dagobah Revision 226, Swamp Revision 34
System returned to ROM by reloadSystem restarted at 00:36:52 UTC Sat Dec 10 2011System image file is "bootflash:cat4000-i9s-mz.122-25.EWA14.bin" cisco WS-C4506 (MPC8245) processor (revision 10) with 262144K bytes of memory.MPC8245 CPU at 266Mhz, Supervisor II+Last reset from Reload1 Virtual Ethernet interface144 FastEthernet interfaces2 Gigabit Ethernet interfaces511K bytes of non-volatile configuration memory.Configuration register is 0x2102
We are experiencing with high CPU input due to ARP input between 20:30 and 22:30 every day At this time we have a lot of backup operations. When I look the netflow report, I can't see anything anormal.
We are changing our backup server's NIC card from 1gig to 10Gig. The backup operation's traffic is high (approx 2Gbps level) but 6509 has to be handle this size of traffic.
We are using two 6509E in VSS mode and our image version is s72033-adventerprisek9_wan-mz.122-33.SXJ.bin
20:00
show ip arp summary
--------------
2588 IP ARP entries, with 166 of them incomplete
[Code].....
I'm facing high CPU utilization issue due to a ssh process on 3750 switch. What is the use of SSH proces in the switch? Can I disable it for troubleshooting?
will there be any impact if I disable it?
#sh processes cpu sorted 5min
CPU utilization for five seconds: 99%/0%; one minute: 66%; five minutes: 46%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
159 1896078 589986 3213 3.96% 10.76% 14.00% 0 Hulc LED Process
165 32871 591 55619 77.42% 33.40% 8.85% 3 SSH Process
which process is consuming high memory with my c6509 switch.
View 17 Replies View Relatedwe are using Cisco 6509-E VSS mode [12.2(33)SXI] ipbase image and facing high cpu utilization. In show process cpu output it is showing some "ios-base" process consuming cpu. I attached show cpu output
View 1 Replies View RelatedWe have a Cisco 3845 router configured as a voice gateway with multi SIP trunks. But when it reachs 200 calls traffic, the CPU increase to 60-70% and caused by CCSIP_SPI_CONTROL process.
CPU utilization for five seconds: 46%/30%; one minute: 54%; five minutes: 58%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
377 400729448 171017979 2343 6.31% 10.71% 12.44% 0 CCSIP_SPI_CONTRO
[Code].....
I found cpu load around 90 - 100% on cisco 3845, so I show tech-spec and show log on router and found process "Virtual Exec" use high load. I'm not sure this situation make high latency time on my network.
View 3 Replies View RelatedWe are running a stack of 2 WS-C3750X-24S-E's with IOS version 12.2(58)SE2 and we are seeing continuous high processor utilization involving the hl3mm process. The stack is configured for PIM Sparse mode, with 2 upstream Nexus 5596'es acting as both RP candidates and as BSRs. The hl3mm process generally runs at about 19% but can spike up into the 60% range.Symptoms on the 3750X are spiking latency and sluggish CLI perfformance. I thought at first that we might be running into SDM limits, but the "show platform tcam utilization" show that we are far under the limits of the default SDM template. Performing the "show ip pim (vrf name) bsr-router" command freezes the system and takes 20-30 seconds to return results. Similiarly configured WS-C3750G-12S running 12.2(55)SE3 does not exhibit these same issues.
View 4 Replies View RelatedI have in my router 2801, one link with 20 MB WAN Connection, and it is presenting high cpu utilization with 97% Interrupt Errors when start one download.
I exchanged it to another router the 2811 and it presented the same results. I read the cisco document about Router Performance.
And it speaks about the 2801 supports 46 Mbps using CEF/Fast Switching and 1.5Mbps using only Process Switching, and 2811 supports 61.44 CEF and 1.5Mbps Process Switching.
I need to know if the NAT Process is process switching or CEF Switching. Because if it was process switching the router is working in the max capacity and i will need to exchange the hardware to a better hardware.
I have two core switches - 4506E, and i noticed there are frequent cpu spikes on both of the cores switches. As its spikes intermitendly i couldnt able to anlyze the issue. I need inputs on the following,
1) Is there any Free CPU process monitoring tools to identify which process is spiking ?
2) Troubleshooting techniques to identify the issue.
We have a Cisco 886 configured with two WAN's (ATM0 connected to a DSL line and Fa3 connected to a CMTS modem).We're running DMVPN over the Cable network and GetVPN over the DSL line. When the DSL line is down we see a lot of CPU peaks up to 90%.The CPU peaks are caused by the process "DSL state machine". As soon as the DSL line has sync and the ATM0 interface goes UP the CPU peaks disappear. What we'd like to know is if this constant extra CPU load will have an impact on other resources like normal routing & switching or more specific IPSEC handling. Is it for example possible that establishing an IPSEC tunnel will fail because of the CPU peaks?
View 11 Replies View RelatedI have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. URL We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
View 1 Replies View RelatedI have an issue with 7600 router where CPU goes up to 60-70% and memory is also high. Both due to BGP Router process. [URL] According to our baseline it should not be more than 40% at any given time. We see high CPU uptp 70% consistently.
CPU utilization for five seconds: 99%/0%; one minute: 57%; five minutes: 55%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
442 66173704 90234125 733 96.86% 46.09% 46.30% 0 BGP Router
7 509291060 26330202 19342 1.17% 3.90% 2.99% 0 Check heaps
Router has 1 eBGP session with ISP from where it downloads whole IPv4 internet routing table and two IBGP session with other two rotuer. When I look at BGP summary table I see many updates received from ISP and sent out to IBGP neighbors. Also did debug BGP updates to confirm it.
We are seeing this issue since ISP has upgraded their router 20 days ago. Router also seen following error.
%BGP-6-BIGCHUNK: Big chunk pool request 628 for community. Replenishing with malloc
I have not reset the BGP session with ISP yet. Is there any way I can supress BGP updates coming from ISP and see if CPU and memory USAGE reduces. IOS version 12.2(33)SRD and RSP720 with PFC 3cXL
Based on the stace trace, how do I determine what object is being polled??? (what is causing the high cpu for SNMP ENGINE)
From the “show stack 295” output (SNMP ENGINE)
router>show stack 295
Process 295: SNMP ENGINE
Stack segment 0x68226DC0 - 0x68229CA0
FP: 0x68229BD0, RA: 0x62A0D95C
FP: 0x68229BF8, RA: 0x628276A8
FP: 0x68229C68, RA: 0x629FBE08
FP: 0x68229C80, RA: 0x629FBDEC
Each time I enter show run on my router 2821, it takes ages to display and I have a cpu peak from the ssh process ( I am connected through SSH)
RTR-2821-01#sh proc cpu sorted
CPU utilization for five seconds: 96%/21%; one minute: 34%; five minutes: 22%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
55 26948 814 33105 74.96% 16.92% 5.87% 323 SSH Process
We suddenly noticed high CPU utilization on one of our 7600 routers. I output of show process CPU showed high utlization for the FM core process. I looked it up but did not find information on what this process does. [code]
View 4 Replies View RelatedI have a Catalyst Switch 6000. Inoticed that after the execution of the job inventory in LMS, and after the snmp queries reached the equipement, the cpu value reached 98-99 % due to the process : PDU DISPATCHER (what’s it ?)
I have also a script running in the switch to observe the differents logs. For exemple, when high cpu is obtained, the message bellow appear :
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
« %SNMP-3-INPUT_QFULL_ERR: Packet dropped due to input
....
We are in the process of switching our infrastructure of our routing/firewalls/vpns over to cisco. We are switching our first location and one of the issues I'm struggling with is windows authentication pass-through for internally hosted web pages. Meaning, user inside our network has the 2921 as their default gateway, they try to access a web page that is hosted on the internal network but is secured with windows authentication. In the past, because they are logged into the domain internally, the website authenticates and loads. After switching to the Cisco, it asks for a password even though they are logged in.
Because its the web server that actually authenticates I'm not sure why the router isn't allowing that to happen, but I can't think of anything else that could be causing this behavior.
My client using 3845 as a core router . 200 number of branch are connected through 6 ISP.Some of days average process shows 90 % . Max time 50 %.In the morning when Branch location are off then time also high utilization.High utilization is not continue after intervals of time or periodic time its goes to high.
have any solution for that ?. before once 3845 is crash for that. another is ready for replacee.We test another device like core switches for observation CPU rate.
I have a problem with SNMP. I using Cisco 3845 in distribution layer. >600 subinterfaces. When my managment system send response - the cpu Utilization on cisco3845 near 100%. I want to prohibited my Cisco answer on response about interface status.
View 2 Replies View RelatedI am seeing a high number of discards reported on one of my monitored WAn rtr (3845). Solarwinds Orion NPM is reporting a steady flow of error on two links, but not all links. What is the typical cause of these reported discards? I see no error or counter increases in the >sh int xx; where xx is the interface shown in the solarwinds reports Google tells me that "An interface discard is simply where the device has decided to discard a packet for some reason. The reason a device discards the packet(s) is typically hard to tell. It could be a corrupt packet, that the device is busy, buffer overflows, packet size issues, and several other things."
The Orion Network Performance Monitor pulls the discard information reported within Orion in the RFC1213:IfTable, more specifically IfInDiscards and IfOutDiscards. These are the OIDs for IfInDiscards and IfOutDiscards we use to gather this
Interface Errors and Discards:
OID = ifInDiscards 1.3.6.1.2.1.2.2.1.13.
0
OID = ifInErrors 1.3.6.1.2.1.2.2.1.14.
0
OID = ifOutDiscards 1.3.6.1.2.1.2.2.1.19.
[code]....
there are no error and only the outgoing direction has discards? How do i debug this more or get more info on how to track down the root cause?
We are following the ISSU process for upgading a VSS 1440, using the documentation here: URL
After copying image onto both supervisors, when the command:
issu loadversion sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI.bin is run we get the following error:
% CV [ bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXI.bin ] must be named first in BOOT [ bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI.bin ]
The advipservice image is the one running, and the adventerprise is the one we are trying to upgrade to.
document which explians normal booting sequence in a 6500 Switch running IOS. What I am looking for is in which order the image is loaded in SUP, RP, SP etc
View 1 Replies View RelatedI've been reading the documentation for the new 3750v2 switch, and I'm wondering is the IPBase license supports FULL OSPF. The product sheet notes that it supports OSPF in the IPBase license, but then further down the page it notes that for advanced routing functions (EIGRP,OSPF) you need the IPServices license. Are there any limitations to the OSPF process on a 3750v2 with the IPBase license?
View 3 Replies View RelatedWe are looking to upgrade the version of IOS on the 6500s this evening and in preparation i've dowloaded the image to sup-bootdisk. However when trying to update the boot path as follows I see the following error: [code] Why are we seeing this message when the router is not doing anything with ISSU?
View 3 Replies View RelatedThe switch 6500-E is frequently crashing whenever the pm scp process reach 100% .I got it under the command "remote command switch show proce cpu".How to solve the problem. I opened the TAC and the engineer says to upgrade the image12.2(18) sxf.Is there any other work around that would avoid to reimage the switch and reloading.
View 1 Replies View RelatedI have a hub and spoke WAN that conisits of one core location with with a 6500 and nine other buildings using 4006 Catalyst that conenct back to the core via dual gig fiber. We are using EIGRP at each location as well as the core. I was tesing something at one of our buildings decided to hang a 3750 off the 4006 and enable the same eigrp process on the 3750 that is enabled on the 4006 and 6500 (EIGRP 1).
1. All the routes that the 6500 knows about are advertised out to each of the nine locations.
2. The 4006's are all advertising thier directly conencted routes to the 6500.
Onto the location I was testing at:
The 4006 where I was testing at has four vlan interfaces enabled and they are in an UP/UP state. The ip routes from the 4006's directly conencted vlan interfaces propogate to the 6500 at our core location and the 6500 sucsefully propgates these learned routes to all the other 4006's.
This past Friday I configured a 3750x with two /22 vlan interfces and one physical gi port with an IP address and also configured on Ethernet port on the 4006 with an IP address in the same network block as the 3750x gi interface (a /30 netowrk block). I saw both interfaces come up and EIGRP sucesfully established a neighbor adjecency between the 3750x and the 4006.
I noticed that the 3750 advertised out all of it's directly conencted routes to the 4006 and the 4006 advertised it's directly conencted routes to the 3750. However, the 4006 did not advertise any of the routes it had learned from the 3750x to the 6500 and nor did the 4006 advertise any of the routes it had learned from the 6500 to the 4006. My suspicion is that the "eigrp stub connected summary" statement is enabled on both the 4006 and 3750 thus prevenintg them form advertising out any routes other than thier directly conencted routes. Can any of you verify that I'm either correct or inccorect about this?
here are the eigrp statemnets from the 6500 and 4006:
6500:
router eigrp 1
redistribute static
network 10.0.0.0
network 172.16.0.0
network 172.17.0.0(code)
we observe that the process platform causes about 50% cpu load of our Nexus 7010.Could not find any information for what this process is responsible to find out the root cause of the high cpu load.
View 1 Replies View RelatedWe are cutting over from 6500 IOS to Nexus 7000 and have hit "Maximum ospf feature instance limit reached." as we configured up the 7 existing ospf processes - the limit is 4. These existing processes are for various vrf contexts we have. I see you can run multiple vrf contexts under one process - but how does that work in a mixed environment where the ospf neighbours are still ios 6500s? They still expect to see different ospf process id per vrf.
View 2 Replies View Related