Cisco :: LMS 4.0.1 - High Memory Utilization
Oct 12, 2011What causes LMS 4.1 to have high memory utilization?
View 4 Replies
ADVERTISEMENT
Cisco WAN :: High Memory Utilization In 7206 Router
Jul 29, 2012We have a 7206 router which acts as a MPLS Hub router for around 100+ remote locations. Bandwidh at mpls hub(terminated on this router) is 50 Mbps.
We have noticed that Memory utilization in this router gradually increases and when it reaches 100% this router hangs. It happence in frequesncy of 10 days and we have to restart the router when memory is 100%.
CPU utilization is normal i.e below 20%, WAN bandwidth will never cross 30mbps.
We are running OSPF on this router
Cisco Firewall :: Very High Memory Utilization In PIX 515e?
Feb 15, 2012We had two PIXes in our environment and working as a active-failover mode. Its noted in now a days the active PIX memory utilization is 98% and for standby PIX it is 96%. And also in some times we were experiencing packet loss to the ip of active PIX and which reflects in the inside servers access also. During that time the active pix was not accessible via ssh as well as ASDM. We have tried reloading the PIX and changing failover state of the PIX, but it results only a temporary solution. Current memory installed is 128 MB (maximum upgraded), so a upgrade is also not possible. Please see the show command outputs from the PIX. Current Software version is 7.2(4)
sh memory output (PIX 1 - active)
Free memory: 4850944 bytes ( 4%)
Used memory: 129366784 bytes (96%)
[code]....
1) How we can pin point the root cause of this high memory utilization?
2) What might be the reason for the high memory utilization for the standby pix (96%), still the PIX is in idle state?
3) Is it a hardware issue or a memory leak issue, then how can we find out?
4) Is a software upgrade to new version resolves the memory issue?
Cisco Infrastructure :: 2960 - High I / O Memory Utilization
Oct 26, 2011We recently installed two 2960, both of them with this fw version:
Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
The switches see very few traffic (under 40MB on all interfaces, summed, so far), however, I/O memory utilization is about 80% as can be seen from the show memory command:
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor 2B89A18 73969000 27198964 46770036 45060368 29367536
I/O 6200000 14680064 12185292 2494772 2323116 2380896
Driver te 1A00000 1048576 44 1048532 1048532 1048532
The memory allocated is almost all Packet Data, by init, "sho memory io dead" returns zero, the memory usage seems constant, there are no errors on the log, the switches operate correctly, no packet has ever been dropped, CPU usage is about 4%.
Here I showed info for one switch, the other is in the same situation. I just want to know if this behavior is expected, I don't want to find out problems when the switches will be in production whit real traffic.
Cisco :: High Memory Utilization After Few Days - Ciscoworks LMS 4.0.1
Sep 18, 2011I have the problem that our ciscoworks server gets out of memory after few days. The memory utilization is always getting higher an higher (above 95%). Sometimes it is only after 3 days and sometimes it is after 1 week. So it happens not regularly. I have made an screenshot from the services which use a lot of memory. And at this time the memory utilization is getting higher and higher again....I think there is a problem with tomcat or dbsrv10.exe, there are also a lot of cwjava.exe running.
View 8 Replies View RelatedCisco Firewall :: High Memory Utilization On ASA 5510
Sep 13, 2012We recently added about 400 users to our network for a total of 1000. Looking at the ASDM we are holding very tight to 75% utilization and we have 256mbs. This is also running IOS 8.2(1). Our firewall recently crashed after a major download was forced through it. This was after only being booted up for about a week. We had reloaded it a week prior after having ran it for about a year without issue. We havent made any changes in the last month other than adding more users to our network.
View 3 Replies View RelatedCisco Switching/Routing :: High Memory Utilization SW 3750
Sep 6, 2012I have a Switch WS-C3750E-48PD-SF with IOS 12.2(58)SE2 which reports more than 80% in utilization of memory I don't know what is causing the high memory utilization.
View 14 Replies View RelatedCisco Switching/Routing :: 6509 High Memory Utilization?
Dec 6, 2011I've noticed that my 6509's running VSS seem to have high I/O memory utilization.
I/O memory: Sw/Mod Bytes: Total Used %Used
1/1 8126344 7886544 97%
1/2 11796240 11442472 97%
1/5 RP 12058384 10715832 89%
1/5 SP 8388608 8104304 97%
1/7 8126344 7886544 97%
[code]....
Cisco Switching/Routing :: 2960 High Memory Utilization
May 2, 2013I noticed on the 2960 switches we have deployed that are running the latest IOS, 12.2(58)SE2, memory utilization is really high (almost 80 percent). I have not noticed any side effects but I wanted to verify this is acceptable. My question is does the high memory utilization matter? I see this may be related to bug CSCtw83946 but no resolution is mentioned.
I did some testing various IOS revisions and below is what I have found using a WS-C2960-48TC-L with default configuration and only my laptop connected to a switchport in vlan1. You will notice memory utilization will grows with each version but jumps drastically with 58. One difference with 58 I needed to use a different command to retrieve memory utilization. The output was gathered by pasting the output of the show command into the Cisco Output Interpreter on their website.
IOS
Show Command
Output
c2960-lanbasek9-mz.122-35.SE5.bin
show memory
[Code]....
Cisco Switching/Routing :: High Memory Utilization In WS-C2960-48TT-L
Nov 9, 2012I am facing high memory utilization in Cisco 2960 switch having IOS version 12.2(55)SE3.
The error we are getting is:
A "LiveHealthAlarm" event has occurred, from SwCiscoIOS device, named Switch2960. eHealth Alarm Start Time - Fri 09 Nov,2012 - 03:02:48 eHealth. Switch2960-RH-MemoryPool-Processor-Processor-1.Memory utilization high-Threshold set at 70%SPECTRUM ALARM ID|22233284 I have attached the logs also.
Cisco Switching/Routing :: 3750 Stack - High Memory Utilization?
Jan 21, 2012I have a new cisco 3750 stack comprised of 8 members (6 x 3750G-48PS and 2 x 3750V2-48PS) running 'c3750-ipservicesk9-mz.122-58.SE2.bin'. I am seeing high memory utilisation, it seems to sit fairly stable and I do not see an increase but this has only been running a few days. No errors or performance issues. Should this be a cause for concern?
View 3 Replies View RelatedCisco Switching/Routing :: 3750g And 3750x High Memory Utilization?
Jun 11, 2013We had a stack of 4 qty 3750g running IP base on ver 12.2.32, then installed a 3750x to the stack and upgraded the whole stack to 15.0.2 SE3. In doing so, we noticed that the memory utilization jumped from 60-70% to 83-84%.
We had the same issue occur when upgrading to 15.0.2 SE3 on another stack that was 6 qty 3750g running ip-services, but this one jumped to 90%. On the 6 qty stack, we downgraded to 12.2.55 and the memory util went back down to 60-70%.
On the mixed stack, we replaced the 3750x with another 3750g and downgraded the whole stack to 12.2.55, however, the memory utilization did not drop down. As far as I can tell, no config changes have changed from the original IOS.
Cisco Switching/Routing :: C2960-24-TT-L - Switch Memory Utilization High After Upgrading IOS
Nov 8, 2011I upgraded the newest IOS 15.0(1)SE for our SW C2960-24-TT-L, the process was succeseful. However, we found SW memory utilization raised to 82% this morning in normal situation. (Momery: Total 21341260, Used17471692) Did you guys meet the same problem after upgrading to 15.0(1)SE? I also would like to know what the normal memory utilization is? and what is the impact of memory utilization highly?
View 8 Replies View RelatedCisco Switching/Routing :: High Memory Utilization Of 3560 Switch After Upgrade IOS
Mar 5, 2013I upgrade the IOS of my switch 3560 from C3560-IPBASE-M), Version 12.2(25)SEB4, To C3560-IPBASEK9-M), Version 12.2(55)SE5 after that the utilizatio of the memory increase to 80% I attached the output of show memory statistics history
View 5 Replies View RelatedCisco Switching/Routing :: High Memory Utilization On Line Card 6748 And 6724?
Apr 15, 2012I am writing with regard to a high memory utilization that we have on a pair of line card WS-X6748-GE-TX and WS-X6724-SFP for a VSS 6500. I am enclosing a little part of the "show tech"of this VSS 6500 where is possible to see the high memory utilization of the line cards 1/1, 1/2, 2/1, and 2/2, in despite of having some ports in state connected. In addition of this, the IOS installed on VSS 6500 is s72033-ipservicesk9_wan-vz.122-33.SXI6.bin for checking if there are some bugs affecting the behaviour of the Switch for this case.
System Resources
PFC operating mode: PFC3C
Supervisor redundancy mode: administratively sso, operationally sso
Switching resources: Sw/Mod Part number Series CEF mode
1/1 WS-X6748-GE-TX CEF720 CEF
1/2 WS-X6724-SFP CEF720 CEF
[code]....
Cisco Firewall :: PIX 501 - Memory Utilization?
Jul 6, 2011I've deployed many Cisco PIX 501 v6.3.3 either as normal firewalling feature and/or with VPN features enabled. I noticed in all my deployments, regardless if it's during peak hours or after office hours, the memory utilization is always consistent 11MB utilized over the total of 16MB(memory default size).
View 3 Replies View RelatedCisco WAN :: 3845 Memory Utilization Increases
Jun 1, 2011Cisco 3845 router (256RAM / 64Flash), increases the cpu utilization upto 70~80 percent, during the time of high utilization, I am unable to run show command on router.The configuration is simple, this is connected with two internet links (24Mbps and 8Mbps) and its about 600~700 users are using internet.show version, show memory and show process cpu outputs are attached here.
View 7 Replies View RelatedCisco Firewall :: ASA 5520 Memory Utilization Over 799%
May 2, 2013I was looking at my CISCO ASA 5520 and i found something really strange
ciscoasa/VPN-context# sh mem detail
Used memory: 4259249568 bytes (793%)
------------- ----------------
Total memory: 536870912 bytes (100%)
but when I look at the system context this is what I see
ciscoasa# sh mem
Free memory: 170829000 bytes (32%)
Used memory: 366041912 bytes (68%)
------------- ----------------
Total memory: 536870912 bytes (100%)
As far as I know the ASA is working good.
Info of the device
Hardware: ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Cisco Firewall :: Memory Utilization On 5510?
Nov 21, 2012Just want to check with you about memory utilization on the Asa 5510 ..
Free memory: 19%
Used Memory: 81%
Is this normal? Because we hade a problem this morning and the memory was at 100%..
Device Manager version 6.1(5) 57
Hardware: ASA5510-K8, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Cisco Routers :: SA520 Memory Utilization
Aug 7, 2011We have a Cisco SA520 Router (Firmware 2.1.18)We are only using this for about 1 month now. Router seems ok its justI am worried about the Memory utilization which reach to 62% (144/234 MB)Is this something to worry about?How can I utilize this by lowering down the usage?
View 3 Replies View RelatedCisco :: Memory Utilization OID For Catalyst 6506 Switch
Dec 26, 2012We have one Catalyst 6506 ( with WS-SUP720-3B, IOS is 12.2(18)SXF14 ) and one Catalyst 6509 ( with WS-SUP720-3B, IOS is 12.2(18)SXF17a ). We used WhatsUP to collect I/O & process memory utilization for both switches. The memory utilization for Catalyst 6509 was ok, but it seems not correct for Catalyst 6506 ( show proc memory displayed the total memory is 512MB, but the WhatsUP displayed only 64MB only )
View 1 Replies View RelatedCisco AAA/Identity/Nac :: ACS Memory Utilization Limit With CSACS 1121
Aug 21, 2012We have 2 CSACS 1121 with Cisco ACS 5.2.0.26.10 The primary server manages 20000+ authentications per day. Its memory utilization increases everyday. It is now at 83% , there a limit?,What will happen when memory utilization reach this limit?,What can we do to purge memory utilization? (reboot, service restart.
View 11 Replies View RelatedCisco WAN :: 5540 - Memory Utilization Getting Higher When Adding Tunnel
Jul 21, 2011We terminated about 25 site-to-site VPN tunnels on the Cisco ASA 5540 (2 GB RAM). It appears that the memory utilization is getting higher when adding the tunnel. We are planing to remove those 25 VPN tunnels out 5540, and soon we will add additional 40 VPN tunnels on it. So it will be total around 65 tunnels, and maybe add couple tunnels per year for the future grow, but about 25 VPN tunnels are using at all the time, the others are just backup purpose, standby only. We are looking for the new network device (router or ASA) to accommodate the needs. Which network device is better to handle VPN tunnel for this infrastructure?
View 5 Replies View RelatedCisco Firewall :: CSCsg43844 Standby Pix With High Memory
Jul 3, 2012Come across pix 525 with 7.2.4 , 256 MB RAM, experienceing high memory utilization ?.show memory was giving used memory = 97%.All I had done was, i did a reboot of the firewall since we were not able to take the control of the f/w.I wonder why only the standby f/w had this issue and not the primary does not have, just to rule out that it was not due to Traffic.I have searched in bugtool kits and support forums and did not find anything relevant except for a similar issue for ASA CSCsg43844.
View 3 Replies View RelatedCisco Switching/Routing :: 2960-S High Memory Use In 15.0 (2) SE
Dec 9, 2012I am noticing high memory used on my 2960-S I am running 15.0(2)SE. I am concerned that there is a problem with this model and IOS.
View 2 Replies View RelatedCisco WAN :: High CPU Utilization On 7606?
Sep 28, 2012Our Router 7606 is in a problem with high CPU Utilization. We are using one EBGP and one IBGP session. We are also running OSPF with area 0 between two IBGP router to exchange few local networks. When bandwidth cross 100 MB than only CPU use become 100%. when bandwidth consumption is 80MB CPU use become 80% end so on.
Out put is when bandwidth consumption is 34MB
CPU utilization for five seconds: 44%/43%; one minute: 42%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
78 44 9625 4 0.39% 0.03% 0.00% 2 Virtual Exec
13 40 375 106 0.07% 0.00% 0.00% 0 ARP Input
30 116 1098 105 0.07% 0.01% 0.00% 0 IPC Seat Manager
[code]....
Cisco :: High CPU Utilization On 7609-S?
Aug 10, 2011I have a hight CPU utilisation problem in my CISCO7609-S routers. the cpu utilisation can rise 99% et this is usually. In the moment of hight CPU the the process CPU give the following:
the show processe cpu history give: show version
Cisco WAN :: 2811 High Cpu Utilization
Apr 29, 2013I have a 2811 that is really hitting the CPU hard. Nothing shows on CPU processes. It has an IPsec VPN tunnel back to HQ which also has a 2811 that terminates the VPN. The HQ has 2-3 IPsec tunnels to other remote sites. The CPU at the HQ avg 50% utilization during business hrs, peaks at about 80%. The remote one is very high 95% peaks, avg 80%-95% during business hours with bandwidth utilization of only 10-20Mbps. I read somewhere that its possible that fragmentation could be causing this. My question is, if I set the MTU to 1450 on the remote, I am guessing I will need to do all the other routers as well, the HQ and other remote sites? Siince they use the same outside interface to my HQ, is that correct?
View 3 Replies View RelatedCisco WAN :: CPU Utilization High In 2811
Jun 23, 2011We have Cisco 2811 router and facing high CPU utilisation as 70%/67%;,IOS Runing :c2800nm-advsecurityk9-mz.124-3f.bin.
View 4 Replies View RelatedCisco WAN :: High CPU Utilization On 7206VXR
Jan 7, 2013High cpu utilization on cisco 7206 vxr router.[code]
View 2 Replies View RelatedCisco WAN :: High CPU Utilization On 7206VXR (NPE-G1)
Jun 20, 2012I am observing very high CPU utilization on my Cisco 7206VXR (NPE-G1) Router. We have done all the necessary troubleshooting but not able to identify root cause. [code]
View 10 Replies View RelatedCisco :: Prime 4.2 - High CPU Utilization
Dec 4, 2012I am running Cisco Prime 4.2(UNIX version) on a VM. CPU utilization will run between 90 and 100% constantly. Reloading the server will stabilize the CPU for a short period of time, however the CPU usage will always return to 90-100% utilization. Currently I have about 130 devices added to the system.
View 1 Replies View RelatedCisco WAN :: C4507R High CPU Utilization
Jun 12, 2013we have 2 Cisco C4507 Switches working As Core Layer, but the CPU Utilization is about 54% most of the time and sometimes it goes up to 70% or 80% also.
which services are causing this utilization. [code]
